Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Simos
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 6

Removed text is struck through; added text is highlighted.

Simos 16 is a Continental petrol engine-management family used on some supercharged 3.0 V6 TFSI applications. Audi's published technical data identifies Simos 16 on the 245 kW Q7 3.0 TFSI quattro described there. Exact ECU, hardware and software identifiers are needed to establish the variant and calibration in a particular vehicle.

Applications and identification

The Audi Q7 technical specification describes a mechanically supercharged 3.0 V6 with combined direct and manifold injection, two intercoolers and Simos 16 engine management. It does not identify a Simos 16 suffix on the cited sheet. It also describes cylinder-selective adaptive knock control and lambda control. The entry is an example, not a complete fitment list.

APR's 2017 product announcement lists Simos 16 on selected supercharged 3.0 TFSI applications; it describes its own products and hardware combinations, not all vehicle and software combinations. Some earlier 3.0 TFSI installations use Simos 8.4 or 8.5. Record the ECU part number, hardware, software and calibration before selecting a file or procedure.

ProcessorThe AutoTuner compatibility list (tool compatibility listing, 28 October 2026) gives the Infineon TC1791 (TriCore) as the microcontroller its tool addresses for Simos 16.11 and Simos 16.21; it is the same device the list gives for the Simos 18 family. This is a tool vendor's statement, not Continental documentation, and it does not identify the flash or EEPROM devices.

Related engine design: EA837 evo

Audi Self-Study Programme 624 describes the fourth-generation EA837 evo using engine code CREA as its example. It calls that engine's management “Simos” without stating the ECU generation. The following is engine-system context; the programme alone does not prove that every CREA or EA837 evo has a Simos 16.

The documented engine combines FSI direct injection and MPI manifold injection, and uses a belt-driven Roots supercharger with an electromagnetic clutch. At low and medium engine speeds and low load, the clutch can release the drive; it engages when required. A control flap and throttle participate in managing air and the transition. Audi describes a supercharger speed sensor G688 used in clutch engagement control and monitoring. A calculated stress factor, rather than a dedicated clutch temperature sensor, provides a basis for protecting the clutch against repeated switching. These descriptions are specific to SSP 624's system.

On the documented EA837 evo, direct and port injection can be used in different combinations as operating conditions change. The presence of both systems and their control should be checked on the actual engine and calibration. The earlier Simos 8 overview describes a different 3.0 TFSI example; do not transfer its component or map assumptions automatically.

For the documented magnetic-clutch and G688 control system, log review and a scoped Q7 bulletin example, see EA837 evo supercharger clutch diagnosis.

See EA837 evo dual injection and fuel pressure diagnosis for the CREA system example, mode-sensitive logs and a separately scoped CREC service bulletin.Charge cooling and pressure sensors on the EA837 evo exampleAudi SSP 624, pages 23 and 29–33, describes the CREA engine's two charge-air coolers and a separate charge-air cooling circuit. Its V188 pump receives a pulse-width-modulated request from the engine control unit and varies delivery according to cooling conditions. The pump self-tests when supplied and waits for the control signal before entering controlled operation; the programme says its diagnostic events are stored in the engine ECU. Its electrical pin assignments differ from the third-generation example. Do not transfer wiring or judge a pump from its behaviour at one temperature or with supply voltage alone; use the actual vehicle's current guided test and wiring information.The same programme identifies the example's G447 charge-pressure and G71 manifold-pressure sensors as digital SENT devices. A third-generation sensor's analogue-voltage test or scaling should not be assumed to apply. Check the exact sender, circuit, data protocol, diagnostic definition and units before interpreting a pressure trace. If charge temperatures or performance vary between runs, compare ambient and intake temperatures, load, charge pressure, coolant-circuit state and relevant faults at repeatable conditions. A temperature rise alone does not prove a failed pump: coolant flow, trapped air, heat exchange and other operating conditions also need vehicle-specific diagnosis. The source identifies the CREA ECU as Simos without a generation suffix, so these details are related engine context rather than proof of identical equipment on all Simos 16 installations.

Tuning and logging considerations

Identify the fitted supercharger, pulley sizes, cooling and fuel system before selecting a calibration. APR's product announcement distinguishes its stock-hardware calibration from single- and dual-pulley packages; those requirements apply to its own offerings, not to every product or vehicle. Do not assume a quoted stage or power figure establishes the correct hardware or fuel for another calibration.

After establishing a fault-free baseline, log supported channels for requested and actual charge pressure, throttle and bypass behaviour, intake and coolant temperatures, lambda target and actual, fuel pressures, ignition and knock correction. Where available and correctly defined, examine supercharger speed, clutch command or status, and injection-mode information. The availability, units and whether values are measured or modelled depend on software and diagnostic equipment. An unexpected transition or lack of boost needs diagnosis of the control, drive and mechanical system; it is not proof that a torque limit should be raised.

Match definitions and checksums to the exact software. The sources here do not establish universal map addresses, safe boost or ignition targets, or an interchangeable programming method. Confirm the chosen tool's read/write support, stable supply and a verified recovery path before programming.

For a file-specific Q7 torque/load map example and the limits of the commercial definitions, see Simos 16.21 Q7 torque and air calibration reference.

Sources

Audi Q7 3.0 TFSI quattro 245 kW technical specification. Simos 16, charge system and combined injection for that vehicle. Accessed 17 November 2026. Audi Self-Study Programme 624, EA837 evo 3.0 V6 TFSI, French edition; English text rendering. CREA engine system, clutch and fuel strategies; names Simos but not its generation. Accessed 17 November 2026. APR: 3.0 TFSI Simos 16 tuning suite, 2017. Vendor applications and product-specific hardware requirements. Accessed 17 November 2026. AutoTuner compatibility list, export dated 28 October 2026. MCU column for Simos 16.11 and 16.21 (TC1791). Accessed 19 November 2026.Audi Q7 3.0 TFSI quattro 245 kW technical specification. Simos 16, charge system and combined injection for that vehicle. Accessed 17 November 2026. Audi Self-Study Programme 624, EA837 evo 3.0 V6 TFSI, French edition; English text rendering. CREA engine system, clutch and fuel strategies; names Simos but not its generation. Accessed 17 November 2026. APR: 3.0 TFSI Simos 16 tuning suite, 2017. Vendor applications and product-specific hardware requirements. Accessed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Simos 16

Simos 16 is a Continental petrol engine-management family used on some supercharged 3.0 V6 TFSI applications. Audi's published technical data identifies Simos 16 on the 245 kW Q7 3.0 TFSI quattro described there. Exact ECU, hardware and software identifiers are needed to establish the variant and calibration in a particular vehicle.

Applications and identification

The Audi Q7 technical specification describes a mechanically supercharged 3.0 V6 with combined direct and manifold injection, two intercoolers and Simos 16 engine management. It does not identify a Simos 16 suffix on the cited sheet. It also describes cylinder-selective adaptive knock control and lambda control. The entry is an example, not a complete fitment list.

APR's 2017 product announcement lists Simos 16 on selected supercharged 3.0 TFSI applications; it describes its own products and hardware combinations, not all vehicle and software combinations. Some earlier 3.0 TFSI installations use Simos 8.4 or 8.5. Record the ECU part number, hardware, software and calibration before selecting a file or procedure.

Related engine design: EA837 evo

Audi Self-Study Programme 624 describes the fourth-generation EA837 evo using engine code CREA as its example. It calls that engine's management “Simos” without stating the ECU generation. The following is engine-system context; the programme alone does not prove that every CREA or EA837 evo has a Simos 16.

The documented engine combines FSI direct injection and MPI manifold injection, and uses a belt-driven Roots supercharger with an electromagnetic clutch. At low and medium engine speeds and low load, the clutch can release the drive; it engages when required. A control flap and throttle participate in managing air and the transition. Audi describes a supercharger speed sensor G688 used in clutch engagement control and monitoring. A calculated stress factor, rather than a dedicated clutch temperature sensor, provides a basis for protecting the clutch against repeated switching. These descriptions are specific to SSP 624's system.

On the documented EA837 evo, direct and port injection can be used in different combinations as operating conditions change. The presence of both systems and their control should be checked on the actual engine and calibration. The earlier Simos 8 overview describes a different 3.0 TFSI example; do not transfer its component or map assumptions automatically.

For the documented magnetic-clutch and G688 control system, log review and a scoped Q7 bulletin example, see EA837 evo supercharger clutch diagnosis.

Tuning and logging considerations

Identify the fitted supercharger, pulley sizes, cooling and fuel system before selecting a calibration. APR's product announcement distinguishes its stock-hardware calibration from single- and dual-pulley packages; those requirements apply to its own offerings, not to every product or vehicle. Do not assume a quoted stage or power figure establishes the correct hardware or fuel for another calibration.

After establishing a fault-free baseline, log supported channels for requested and actual charge pressure, throttle and bypass behaviour, intake and coolant temperatures, lambda target and actual, fuel pressures, ignition and knock correction. Where available and correctly defined, examine supercharger speed, clutch command or status, and injection-mode information. The availability, units and whether values are measured or modelled depend on software and diagnostic equipment. An unexpected transition or lack of boost needs diagnosis of the control, drive and mechanical system; it is not proof that a torque limit should be raised.

Match definitions and checksums to the exact software. The sources here do not establish universal map addresses, safe boost or ignition targets, or an interchangeable programming method. Confirm the chosen tool's read/write support, stable supply and a verified recovery path before programming.

Sources

Revision 6: Simos 16

Simos 16 is a Continental petrol engine-management family used on some supercharged 3.0 V6 TFSI applications. Audi's published technical data identifies Simos 16 on the 245 kW Q7 3.0 TFSI quattro described there. Exact ECU, hardware and software identifiers are needed to establish the variant and calibration in a particular vehicle.

Applications and identification

The Audi Q7 technical specification describes a mechanically supercharged 3.0 V6 with combined direct and manifold injection, two intercoolers and Simos 16 engine management. It does not identify a Simos 16 suffix on the cited sheet. It also describes cylinder-selective adaptive knock control and lambda control. The entry is an example, not a complete fitment list.

APR's 2017 product announcement lists Simos 16 on selected supercharged 3.0 TFSI applications; it describes its own products and hardware combinations, not all vehicle and software combinations. Some earlier 3.0 TFSI installations use Simos 8.4 or 8.5. Record the ECU part number, hardware, software and calibration before selecting a file or procedure.

Processor

The AutoTuner compatibility list (tool compatibility listing, 28 October 2026) gives the Infineon TC1791 (TriCore) as the microcontroller its tool addresses for Simos 16.11 and Simos 16.21; it is the same device the list gives for the Simos 18 family. This is a tool vendor's statement, not Continental documentation, and it does not identify the flash or EEPROM devices.

Related engine design: EA837 evo

Audi Self-Study Programme 624 describes the fourth-generation EA837 evo using engine code CREA as its example. It calls that engine's management “Simos” without stating the ECU generation. The following is engine-system context; the programme alone does not prove that every CREA or EA837 evo has a Simos 16.

The documented engine combines FSI direct injection and MPI manifold injection, and uses a belt-driven Roots supercharger with an electromagnetic clutch. At low and medium engine speeds and low load, the clutch can release the drive; it engages when required. A control flap and throttle participate in managing air and the transition. Audi describes a supercharger speed sensor G688 used in clutch engagement control and monitoring. A calculated stress factor, rather than a dedicated clutch temperature sensor, provides a basis for protecting the clutch against repeated switching. These descriptions are specific to SSP 624's system.

On the documented EA837 evo, direct and port injection can be used in different combinations as operating conditions change. The presence of both systems and their control should be checked on the actual engine and calibration. The earlier Simos 8 overview describes a different 3.0 TFSI example; do not transfer its component or map assumptions automatically.

For the documented magnetic-clutch and G688 control system, log review and a scoped Q7 bulletin example, see EA837 evo supercharger clutch diagnosis.

See EA837 evo dual injection and fuel pressure diagnosis for the CREA system example, mode-sensitive logs and a separately scoped CREC service bulletin.

Charge cooling and pressure sensors on the EA837 evo example

Audi SSP 624, pages 23 and 29–33, describes the CREA engine's two charge-air coolers and a separate charge-air cooling circuit. Its V188 pump receives a pulse-width-modulated request from the engine control unit and varies delivery according to cooling conditions. The pump self-tests when supplied and waits for the control signal before entering controlled operation; the programme says its diagnostic events are stored in the engine ECU. Its electrical pin assignments differ from the third-generation example. Do not transfer wiring or judge a pump from its behaviour at one temperature or with supply voltage alone; use the actual vehicle's current guided test and wiring information.

The same programme identifies the example's G447 charge-pressure and G71 manifold-pressure sensors as digital SENT devices. A third-generation sensor's analogue-voltage test or scaling should not be assumed to apply. Check the exact sender, circuit, data protocol, diagnostic definition and units before interpreting a pressure trace. If charge temperatures or performance vary between runs, compare ambient and intake temperatures, load, charge pressure, coolant-circuit state and relevant faults at repeatable conditions. A temperature rise alone does not prove a failed pump: coolant flow, trapped air, heat exchange and other operating conditions also need vehicle-specific diagnosis. The source identifies the CREA ECU as Simos without a generation suffix, so these details are related engine context rather than proof of identical equipment on all Simos 16 installations.

Tuning and logging considerations

Identify the fitted supercharger, pulley sizes, cooling and fuel system before selecting a calibration. APR's product announcement distinguishes its stock-hardware calibration from single- and dual-pulley packages; those requirements apply to its own offerings, not to every product or vehicle. Do not assume a quoted stage or power figure establishes the correct hardware or fuel for another calibration.

After establishing a fault-free baseline, log supported channels for requested and actual charge pressure, throttle and bypass behaviour, intake and coolant temperatures, lambda target and actual, fuel pressures, ignition and knock correction. Where available and correctly defined, examine supercharger speed, clutch command or status, and injection-mode information. The availability, units and whether values are measured or modelled depend on software and diagnostic equipment. An unexpected transition or lack of boost needs diagnosis of the control, drive and mechanical system; it is not proof that a torque limit should be raised.

Match definitions and checksums to the exact software. The sources here do not establish universal map addresses, safe boost or ignition targets, or an interchangeable programming method. Confirm the chosen tool's read/write support, stable supply and a verified recovery path before programming.

For a file-specific Q7 torque/load map example and the limits of the commercial definitions, see Simos 16.21 Q7 torque and air calibration reference.

Sources