Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Edelbrock Pro-Flo 4 Plus EFI
Applies to
Edelbrock Pro-Flo 4 Plus EFI
Tool groups
None
Manufacturers
None

Edelbrock Pro-Flo 4 Plus 36160 2015–2017 Ford Coyote: Pro-Flo 4+ 36160 is the manufacturer’s engine-management kit listed for 2015–2017 Ford Coyote. It uses a separate, weather-resistant ECU, a matching terminated harness and an application-specific base calibration; it controls an appropriate modern EFI engine and does not by itself replace a carburettor. Verify the engine generation, reluctor or trigger, sensors, throttle body, pedal, variable-cam and auxiliary harnesses against the exact kit. Edelbrock’s selection guide identifies this engine and kit number.

Edelbrock Pro-Flo 4 Plus 36160 2015–2017 Ford Coyote manufacturer illustration
Edelbrock installation manual cover for the Coyote family; applications and harnesses differ. Edelbrock source; reproduced with permission.

Selection and system layout

Identify the exact ECU, engine and kit part number, intake and throttle, sensor and ignition arrangement. The phone or tablet app is the calibration and monitoring interface, not the ECU. Fuel delivery, return plumbing and auxiliary components depend on the package. Consult the manufacturer documentation for the specific configuration.

Wiring documentation

Use the model-specific Edelbrock source for hardware and wiring. A complete numbered ECU connector table has not yet been verified for this page; do not substitute the assignment of another Pro-Flo or E-Street system.

Manufacturer harness connector references

Edelbrock’s kit 36160 installation manual, PDF pages 19–20, depicts main engine harness 37-1024 and chassis harness 37-1026. These tables identify the labelled branches and customer-wired leads, not the individual cavities of the ECU connectors. Confirm the actual kit, engine-specific extensions and connector orientation before wiring.

Main engine harness 37-1024

Harness labelManufacturer identification
ECUEngine harness connector to the ECU; exact ECU cavity numbering is not supplied
BRIDGEConnection to chassis harness bridge
INJ. R1–R4Four right-bank injector branches, individually labelled R1, R2, R3 and R4
INJ. L1–L4Four left-bank injector branches, individually labelled L1, L2, L3 and L4
KNOCK SENSORConnection to the applicable knock sensor harness
THROTTLEConnection to the application throttle harness
IGNITIONConnection to the application ignition/coil harness
ENGINE POSITIONConnection to the application engine-position harness
SENS/OUTConnection to the application sensors/outputs harness

Chassis harness 37-1026

Harness labelManufacturer identification
ECUChassis harness ECU connection
BRIDGEConnection to main engine harness bridge
CANCAN communication connector
APPAccelerator pedal harness connection
O2 #1Primary oxygen sensor; manufacturer specifies this sensor
O2 #2Optional second oxygen sensor
FUEL PUMPGrey two-way connector; source specifies maximum 10 A, with relay if the pump exceeds this
FANSLow-current ground outputs to fan relay triggers, not direct fan power
MAIN RELAY / FUSE BOXPower distribution and protection
Battery positive / negativeBattery connections; follow the manufacturer’s power and grounding instructions

Chassis flying leads

Wire colourFunctionManufacturer notes
Pink/blackIgnition switch +12 VSupply present in both ON and CRANK per manufacturer
Yellow/blueBrake light switchBrake input senses +12 V with brake pressed; part of drive-by-wire safety
Light blue/pinkTachometer output12 V square-wave output according to the manual

CAN harness connector — documented positions

The manual identifies a Deutsch DT04-4P mating connector and lists the following CAN positions. It does not establish functions for positions 3 and 4 in that description or give an explicit viewing orientation; do not infer them.

Connector positionFunction
1CAN high
2CAN low
3Not specified in cited pin description
4Not specified in cited pin description

Source inconsistency: section 2.2 calls the large ECU connector a chassis-harness connector, while section 3.1 separately calls the chassis-harness connector the smaller one. The drawings label the engine and chassis harnesses separately. Confirm the exact connector identification against the actual harness and Edelbrock before connecting.

Engine-specific harness selection

The manual’s PDF page 7 parts list specifies sub-engine harness 37-1022 and pedal harness 37-1033. Its year range for kit 36160 is 2016–2017, while Edelbrock’s 2023 product brochure lists 2015–2017. Confirm the 2015 engine generation and correct kit with Edelbrock before selecting the harness. Kit manual; Edelbrock 2023 product brochure.