Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
ABS / DSC
Parent
WABCO ABS units
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
WABCO

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

ABS and traction systems directory · WABCO ABS units

WABCO's identification literature distinguishes D version pneumatic ABS from the E version, and shows Basic, cab-mounted and frame-mounted D ECUs. The system is documented for trucks, tractors and buses. The pneumatic designation matters: a separately documented D version hydraulic ABS also exists.

Documented applications

WABCO directs technicians to maintenance manual 30 for D pneumatic ABS. Identify ECU part number, sensor/modulator configuration and the vehicle's brake type before selecting documentation.

Identification and service

Record the full supplier and vehicle-manufacturer part numbers, vehicle VIN and fitted equipment, software version and coding where available. Use the vehicle-specific service information to confirm diagnostic capabilities, component compatibility, bleeding and any setup or calibration. A family designation alone is not a replacement-part specification.

Configurations and identification

WABCO maintenance manual MM30 identifies the D ECU version, part number and sensor/modulator configuration on the ECU identification label. Its three common D-version configurations are 4S/4M (four wheel-speed sensors and four modulator valves), 6S/4M (six sensors and four modulators), and 6S/6M (six of each). D Basic uses 4S/4M only. These describe installed system architecture, not interchangeable ECU part numbers.

Source: WABCO maintenance manual MM30, section 1.

Sources

WABCO D and E ABS identification

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: WABCO D version pneumatic ABS

ABS and traction systems directory · WABCO ABS units

WABCO's identification literature distinguishes D version pneumatic ABS from the E version, and shows Basic, cab-mounted and frame-mounted D ECUs. The system is documented for trucks, tractors and buses. The pneumatic designation matters: a separately documented D version hydraulic ABS also exists.

Documented applications

WABCO directs technicians to maintenance manual 30 for D pneumatic ABS. Identify ECU part number, sensor/modulator configuration and the vehicle's brake type before selecting documentation.

Identification and service

Record the full supplier and vehicle-manufacturer part numbers, vehicle VIN and fitted equipment, software version and coding where available. Use the vehicle-specific service information to confirm diagnostic capabilities, component compatibility, bleeding and any setup or calibration. A family designation alone is not a replacement-part specification.

Configurations and identification

WABCO maintenance manual MM30 identifies the D ECU version, part number and sensor/modulator configuration on the ECU identification label. Its three common D-version configurations are 4S/4M (four wheel-speed sensors and four modulator valves), 6S/4M (six sensors and four modulators), and 6S/6M (six of each). D Basic uses 4S/4M only. These describe installed system architecture, not interchangeable ECU part numbers.

Source: WABCO maintenance manual MM30, section 1.

Sources

Revision 3: WABCO D version pneumatic ABS

ABS and traction systems directory · WABCO ABS units

WABCO's identification literature distinguishes D version pneumatic ABS from the E version, and shows Basic, cab-mounted and frame-mounted D ECUs. The system is documented for trucks, tractors and buses. The pneumatic designation matters: a separately documented D version hydraulic ABS also exists.

Documented applications

WABCO directs technicians to maintenance manual 30 for D pneumatic ABS. Identify ECU part number, sensor/modulator configuration and the vehicle's brake type before selecting documentation.

Identification and service

Record the full supplier and vehicle-manufacturer part numbers, vehicle VIN and fitted equipment, software version and coding where available. Use the vehicle-specific service information to confirm diagnostic capabilities, component compatibility, bleeding and any setup or calibration. A family designation alone is not a replacement-part specification.

Configurations and identification

WABCO maintenance manual MM30 identifies the D ECU version, part number and sensor/modulator configuration on the ECU identification label. Its three common D-version configurations are 4S/4M (four wheel-speed sensors and four modulator valves), 6S/4M (six sensors and four modulators), and 6S/6M (six of each). D Basic uses 4S/4M only. These describe installed system architecture, not interchangeable ECU part numbers.

Source: WABCO maintenance manual MM30, section 1.

Sources