Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Holley EFI standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
Sniper 2 EFI throttle body with integrated ECU
Sniper 2 EFI throttle body with integrated ECU. Image from the Holley manufacturer manual, cover; reproduced with permission.

Sniper 2 is the second generation of Holley's integrated throttle-body EFI system; the ECU and throttle body are a package rather than a generic HP or Terminator module. The 550-511 product information describes updated ECU electronics and a main harness with HyperSpark distributor support.

Wiring and ignition

Holley's system installation diagrams identify a 16-pin main connector, separate CAN and six-pin optional I/O harness for the documented 550-511 arrangement. Its ignition options guide distinguishes a coil-minus RPM-only input from supported timing-control configurations. Verify the specific throttle body, harness, ignition and sensor setup.

See the Holley EFI manufacturer index. Sources reviewed 17 November 2026.

Six-way I/O harness connector

From the Holley Sniper 2 EFI QuickStart guide, for the optional 558-497 I/O harness. Outputs are ground-side relay triggers; consult the guide for current limits and configuration. This table does not document the separate 16-way main connector.

Six-way I/O harness

PinWire colourFunction
AOrangeTPS output, 0–5 V
BBlack/yellowOutput 1, ground-switched relay trigger; default fan 1
CLight blueInput 2, programmable ground input
DLight greenInput 1, programmable ground input; default IAC kick
EGreyTachometer output
FGreen/whiteOutput 2, ground-switched relay trigger; default fan 2

Sixteen-way main connector

Holley’s Sniper 2 QuickStart guide, page 6, identifies all 16 lettered positions of the main harness connection. This connector is separate from the optional six-way I/O harness above. Refer to the source for the connector orientation and the correct ignition wiring. The ECU’s ground outputs are rated at 2 A or less and are relay triggers; do not infer that the pump itself is driven directly by pin R.

PinWire colourHolley functionApplication / note
ARedBattery positive (+)Connects directly to battery positive
BPinkSwitched ignition +12 VMust remain powered during cranking
CYellowCoil negative RPM inputEngine-speed input; ignition-type dependent
DGreenCrank signal negativeEngine-speed signal ground
EGreen/whiteOutput 2 (−)Optional ground-side relay trigger
FOrangeTPS outputOptional transmission-controller TPS signal
GLight greenInput 1 (−)Optional programmable ground input
HBrownCAN 2 highFuture expansion
JOrangeCAN 2 lowFuture expansion
KGreyTach outputAftermarket tachometer
LLight blueInput 2 (−)Optional programmable ground input
MBlack/yellowOutput 1 (−)Optional ground-side relay trigger
NPurpleCrank signal inputEngine-speed signal input
PWhitePoints outputTriggers a CDI ignition box
RBlueFuel pump output (−)Fuel-pump ground output / relay trigger
SBlackBattery negative (−)Connects directly to battery negative

Holley identifies two distinct main harnesses: 558-190 is for an external relay or PDM, while 558-191 incorporates a fuel-pump relay and larger power wire. The downstream pump connection therefore depends on the harness; match the part number and current manufacturer guide.

Optional Sniper EFI power distribution module terminals

These are the 18 terminals of the optional Holley 554-200 power distribution module, not ECU connector pins. Holley’s Sniper 2 QuickStart guide, PDF page 20, diagram 2, labels the following example connections for a Sniper 2 system with PDM and 558-190 main harness. The PDM also has separate battery-positive and battery-negative studs, shown with 10 AWG red and black battery cables. Follow the PDM drawing for orientation and the applicable harness and ignition configuration.

PDM terminalExample wireDiagram connection
114 AWG redFuel pump positive
214 AWG blackFuel pump negative
320 AWG blueFuel pump trigger, ground input
420 AWG pinkSniper switched 12 V positive
512 AWG redSniper main power positive
620 AWG whiteSniper points
720 AWG black/yellowFan trigger, ground
812 AWG blackSniper main ground
9—Optional 2 A positive accessory relay trigger
10—Optional 2 A positive accessory relay trigger
11—Ground for accessory relays on 9 and 10
1212 AWG blackIgnition box main ground
1320 AWG whiteIgnition box points input
1412 AWG redIgnition box main power positive
1520 AWG redIgnition box switched 12 V
1620 AWG pinkSwitched 12 V from ignition switch
1712 AWG blackFan negative
1812 AWG redFan positive