Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
PnPduino standalone ECUs
Applies to
PnPduino standalone ECUs
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

PnPduino Mitsubishi EVO3 is a PnPduino programmable engine-management ECU. Manufacturer product information.

PnPduino Mitsubishi EVO3. PnPduino manufacturer product photograph, reproduced with permission.

Application and identification

Manufacturer identifies the application by a three-plug, 64-position Mitsubishi harness for 4G63T and 4G92/4G93 applications. The product is named EVO3, but the engine and three-plug connection must be checked against the specific vehicle rather than assuming all EVO variants are compatible.

System and wiring

The original trigger can be used; the supplier encourages the supplied 24+1 trigger disc. The original MAF is not used: the ECU’s onboard MAP sensor must be connected. Both high- and low-impedance injectors are listed, and the original resistor box may be removed according to the product instructions. OEM idle servo support and an alternative two-wire idle valve are described.

Connector identification

ConnectorManufacturer descriptionScopeVehicle ECU connectors3 plugs, 64 positions totalConfirm exact mating loom and pinout; the manufacturer’s numbered schedule is transcribed below.

The manufacturer’s model-specific connector schedule is transcribed below. Confirm the specific vehicle, connector orientation and hardware revision.

Software and calibration

Uses Speeduino firmware and TunerStudio. A separate wideband controller and a final tune are required.

See the PnPduino manufacturer index.

Model-specific wiring document

The supplier publishes its own model-specific three-connector pinout with OEM and controller functions, wiring notes and colour-coded changed and unused signals. Check the exact engine and loom before using it. Open the PnPduino pinout document. The separate connector-identification table above is a summary; the manufacturer schedule follows below.

EVO3 manufacturer connector schedule

Transcribed from the PnPduino EVO3 pinout, pages 1–4. The original numbers three connectors 1–26, 31–46 and 51–72, for 64 positions total; numbers 27–30 and 47–50 are not part of the depicted connector numbering. Follow the source diagram, which does not specify whether the view is from the ECU face or wire side. Arduino pin numbers are configuration references rather than connector cavity numbers. Blank source cells are shown as a dash, not assumed unused.

26-way connector

ECU pinOEM functionPnPduino functionArduino pinManufacturer notes1Injector 1Injector 18Wired in Firing order 1-3-4-22Injector 3Injector 27Wired in Firing order 1-3-4-23Radiator FanLow Current 126Spare Low Current 14Idle Servo 1Stepper A1—Stepper Idle Control A5Idle Servo 4Stepper B1—Stepper Idle Control B6Sec Air SolLow Current 227Spare Low Current 27—Ignition 434Wire this to COP2 for sequential COP8Fuel Pump RelayFuel Pump23Fuel Pump9Alarm Warning Light——Not used10IGN Amplifier AIgnition 135Ignition 1 in Wasted Spark11Fan Relay——Not used1212V SW Supply12V—12V Supply from Main Relay13GroundGround—Power Ground (Not Chassis)14Injector 2Injector 45Wired in Firing order 1-3-4-215Injector 4Injector 36Wired in Firing order 1-3-4-216Radiator FanFan24Radiator Fan Output17Idle Servo 3Stepper A2—Stepper Idle Control A18Idle Servo 6Stepper B2—Stepper Idle Control B19Air Flow ResetInput 3A10Spare Analog Input 320—Input 4A11Spare Analog Input 421—Input 2A9Spare Analog Input 222AC Comp RelayFan225Spare Low Current Fan223IGN Amplifier BIgnition 236Ignition 2 in Wasted Spark24Rear Screen OnIgnition 333Wire this to COP4 for sequential COP2512V SW Supply12V—12V Supply from Main Relay26GroundGround—Power Ground (Not Chassis)

16-way connector

ECU pinOEM functionPnPduino functionArduino pinManufacturer notes31TachoTacho Out22Tachometer Output 12V32—CANH—CAN Hi33Fuel Press SolLow Current 328Spare Low Current 334Octane AdjustIdle 210IDLE2 or Spare Hi Current Output35—Idle 19IDLE1 or Spare Hi Current Output36ECU Warning LightLow Current 429Spare Low Current 437PAS Switch——Not used38ECU Relay——ECU to activate Main Relay by IG SW39—VVT11VVT or Spare Hi Current Output40Waste Gate SolBoost12Boost Solenoid41—CANL—CAN Lo42DiagnosticsClutch Switch37Clutch/Launch Switch43DiagnosticsSensor Ground—Sensor Ground44—12V Fused Supply—12V Fused Supply to Sensors45AC SwitchInput 1A8Spare Analog Input 146—12V Fused Supply—12V Fused Supply to Sensors

22-way connector

ECU pinOEM functionPnPduino functionArduino pinManufacturer notes51Start——Not used52Air TempIntake Air TempA5Intake Air Temperature53—Flex Sensor22Ethanol Flex Sensor54Exhaust Temp+Input 5A6Spare Analog Input 555—Input 6A12Spare Analog Input 656LambdaO2A1O2 from Wideband57Exhaust Temp-——Not used58Knock SensorKnock Sensor21Knock Sensor or Digital Hall Input59—Input 7A13Spare Analog Input 760Backup Supply——Not used61Vref 5V5V output—5V output from ECU62IGN Switch Supply12V Ignition Switch—IG Switch to activate Main Relay63Water TempCoolant TempA4Engine Coolant Temperature64TPSThrottle Position SensorA3Throttle Position Sensor65Baro Press——Not used66Road SpeedVehicle Speed Sensor20Vehicle Speed Sensor67Idle Switch———68Cam SensorVR2+18Hall Sensor 2 Input69Crank SensorVR1+19Hall Sensor 1 Input70Air Flow SensorMAP SensorA0MAP sensor input71Ground——Ground72Sensor Ground——Sensor Ground

In this source, CAN high and low are available only with an STM32 processor; ignition and injector assignments depend on the wiring and firing order stated in the table. The source notes an onboard MAP sensor but labels pin 70 as an external MAP input; confirm the actual installed MAP configuration with PnPduino. Position 67 has an OEM idle-switch label but no PnPduino assignment in the table.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: PnPduino Mitsubishi EVO3

PnPduino Mitsubishi EVO3 is a PnPduino programmable engine-management ECU. Manufacturer product information.

PnPduino Mitsubishi EVO3
PnPduino Mitsubishi EVO3. PnPduino manufacturer product photograph, reproduced with permission.

Application and identification

Manufacturer identifies the application by a three-plug, 64-position Mitsubishi harness for 4G63T and 4G92/4G93 applications. The product is named EVO3, but the engine and three-plug connection must be checked against the specific vehicle rather than assuming all EVO variants are compatible.

System and wiring

The original trigger can be used; the supplier encourages the supplied 24+1 trigger disc. The original MAF is not used: the ECU’s onboard MAP sensor must be connected. Both high- and low-impedance injectors are listed, and the original resistor box may be removed according to the product instructions. OEM idle servo support and an alternative two-wire idle valve are described.

Connector identification

ConnectorManufacturer descriptionScope
Vehicle ECU connectors3 plugs, 64 positions totalConfirm exact mating loom and pinout; the manufacturer’s numbered schedule is transcribed below.

The manufacturer’s model-specific connector schedule is transcribed below. Confirm the specific vehicle, connector orientation and hardware revision.

Software and calibration

Uses Speeduino firmware and TunerStudio. A separate wideband controller and a final tune are required.

See the PnPduino manufacturer index.

Model-specific wiring document

The supplier publishes its own model-specific three-connector pinout with OEM and controller functions, wiring notes and colour-coded changed and unused signals. Check the exact engine and loom before using it. Open the PnPduino pinout document. The separate connector-identification table above is a summary; the manufacturer schedule follows below.

EVO3 manufacturer connector schedule

Transcribed from the PnPduino EVO3 pinout, pages 1–4. The original numbers three connectors 1–26, 31–46 and 51–72, for 64 positions total; numbers 27–30 and 47–50 are not part of the depicted connector numbering. Follow the source diagram, which does not specify whether the view is from the ECU face or wire side. Arduino pin numbers are configuration references rather than connector cavity numbers. Blank source cells are shown as a dash, not assumed unused.

26-way connector

ECU pinOEM functionPnPduino functionArduino pinManufacturer notes
1Injector 1Injector 18Wired in Firing order 1-3-4-2
2Injector 3Injector 27Wired in Firing order 1-3-4-2
3Radiator FanLow Current 126Spare Low Current 1
4Idle Servo 1Stepper A1—Stepper Idle Control A
5Idle Servo 4Stepper B1—Stepper Idle Control B
6Sec Air SolLow Current 227Spare Low Current 2
7—Ignition 434Wire this to COP2 for sequential COP
8Fuel Pump RelayFuel Pump23Fuel Pump
9Alarm Warning Light——Not used
10IGN Amplifier AIgnition 135Ignition 1 in Wasted Spark
11Fan Relay——Not used
1212V SW Supply12V—12V Supply from Main Relay
13GroundGround—Power Ground (Not Chassis)
14Injector 2Injector 45Wired in Firing order 1-3-4-2
15Injector 4Injector 36Wired in Firing order 1-3-4-2
16Radiator FanFan24Radiator Fan Output
17Idle Servo 3Stepper A2—Stepper Idle Control A
18Idle Servo 6Stepper B2—Stepper Idle Control B
19Air Flow ResetInput 3A10Spare Analog Input 3
20—Input 4A11Spare Analog Input 4
21—Input 2A9Spare Analog Input 2
22AC Comp RelayFan225Spare Low Current Fan2
23IGN Amplifier BIgnition 236Ignition 2 in Wasted Spark
24Rear Screen OnIgnition 333Wire this to COP4 for sequential COP
2512V SW Supply12V—12V Supply from Main Relay
26GroundGround—Power Ground (Not Chassis)

16-way connector

ECU pinOEM functionPnPduino functionArduino pinManufacturer notes
31TachoTacho Out22Tachometer Output 12V
32—CANH—CAN Hi
33Fuel Press SolLow Current 328Spare Low Current 3
34Octane AdjustIdle 210IDLE2 or Spare Hi Current Output
35—Idle 19IDLE1 or Spare Hi Current Output
36ECU Warning LightLow Current 429Spare Low Current 4
37PAS Switch——Not used
38ECU Relay——ECU to activate Main Relay by IG SW
39—VVT11VVT or Spare Hi Current Output
40Waste Gate SolBoost12Boost Solenoid
41—CANL—CAN Lo
42DiagnosticsClutch Switch37Clutch/Launch Switch
43DiagnosticsSensor Ground—Sensor Ground
44—12V Fused Supply—12V Fused Supply to Sensors
45AC SwitchInput 1A8Spare Analog Input 1
46—12V Fused Supply—12V Fused Supply to Sensors

22-way connector

ECU pinOEM functionPnPduino functionArduino pinManufacturer notes
51Start——Not used
52Air TempIntake Air TempA5Intake Air Temperature
53—Flex Sensor22Ethanol Flex Sensor
54Exhaust Temp+Input 5A6Spare Analog Input 5
55—Input 6A12Spare Analog Input 6
56LambdaO2A1O2 from Wideband
57Exhaust Temp-——Not used
58Knock SensorKnock Sensor21Knock Sensor or Digital Hall Input
59—Input 7A13Spare Analog Input 7
60Backup Supply——Not used
61Vref 5V5V output—5V output from ECU
62IGN Switch Supply12V Ignition Switch—IG Switch to activate Main Relay
63Water TempCoolant TempA4Engine Coolant Temperature
64TPSThrottle Position SensorA3Throttle Position Sensor
65Baro Press——Not used
66Road SpeedVehicle Speed Sensor20Vehicle Speed Sensor
67Idle Switch———
68Cam SensorVR2+18Hall Sensor 2 Input
69Crank SensorVR1+19Hall Sensor 1 Input
70Air Flow SensorMAP SensorA0MAP sensor input
71Ground——Ground
72Sensor Ground——Sensor Ground

In this source, CAN high and low are available only with an STM32 processor; ignition and injector assignments depend on the wiring and firing order stated in the table. The source notes an onboard MAP sensor but labels pin 70 as an external MAP input; confirm the actual installed MAP configuration with PnPduino. Position 67 has an OEM idle-switch label but no PnPduino assignment in the table.

Revision 3: PnPduino Mitsubishi EVO3

PnPduino Mitsubishi EVO3 is a PnPduino programmable engine-management ECU. Manufacturer product information.

PnPduino Mitsubishi EVO3
PnPduino Mitsubishi EVO3. PnPduino manufacturer product photograph, reproduced with permission.

Application and identification

Manufacturer identifies the application by a three-plug, 64-position Mitsubishi harness for 4G63T and 4G92/4G93 applications. The product is named EVO3, but the engine and three-plug connection must be checked against the specific vehicle rather than assuming all EVO variants are compatible.

System and wiring

The original trigger can be used; the supplier encourages the supplied 24+1 trigger disc. The original MAF is not used: the ECU’s onboard MAP sensor must be connected. Both high- and low-impedance injectors are listed, and the original resistor box may be removed according to the product instructions. OEM idle servo support and an alternative two-wire idle valve are described.

Connector identification

ConnectorManufacturer descriptionScope
Vehicle ECU connectors3 plugs, 64 positions totalConfirm exact mating loom and pinout; the manufacturer’s numbered schedule is transcribed below.

The manufacturer’s model-specific connector schedule is transcribed below. Confirm the specific vehicle, connector orientation and hardware revision.

Software and calibration

Uses Speeduino firmware and TunerStudio. A separate wideband controller and a final tune are required.

See the PnPduino manufacturer index.

Model-specific wiring document

The supplier publishes its own model-specific three-connector pinout with OEM and controller functions, wiring notes and colour-coded changed and unused signals. Check the exact engine and loom before using it. Open the PnPduino pinout document. The separate connector-identification table above is a summary; the manufacturer schedule follows below.

EVO3 manufacturer connector schedule

Transcribed from the PnPduino EVO3 pinout, pages 1–4. The original numbers three connectors 1–26, 31–46 and 51–72, for 64 positions total; numbers 27–30 and 47–50 are not part of the depicted connector numbering. Follow the source diagram, which does not specify whether the view is from the ECU face or wire side. Arduino pin numbers are configuration references rather than connector cavity numbers. Blank source cells are shown as a dash, not assumed unused.

26-way connector

ECU pinOEM functionPnPduino functionArduino pinManufacturer notes
1Injector 1Injector 18Wired in Firing order 1-3-4-2
2Injector 3Injector 27Wired in Firing order 1-3-4-2
3Radiator FanLow Current 126Spare Low Current 1
4Idle Servo 1Stepper A1—Stepper Idle Control A
5Idle Servo 4Stepper B1—Stepper Idle Control B
6Sec Air SolLow Current 227Spare Low Current 2
7—Ignition 434Wire this to COP2 for sequential COP
8Fuel Pump RelayFuel Pump23Fuel Pump
9Alarm Warning Light——Not used
10IGN Amplifier AIgnition 135Ignition 1 in Wasted Spark
11Fan Relay——Not used
1212V SW Supply12V—12V Supply from Main Relay
13GroundGround—Power Ground (Not Chassis)
14Injector 2Injector 45Wired in Firing order 1-3-4-2
15Injector 4Injector 36Wired in Firing order 1-3-4-2
16Radiator FanFan24Radiator Fan Output
17Idle Servo 3Stepper A2—Stepper Idle Control A
18Idle Servo 6Stepper B2—Stepper Idle Control B
19Air Flow ResetInput 3A10Spare Analog Input 3
20—Input 4A11Spare Analog Input 4
21—Input 2A9Spare Analog Input 2
22AC Comp RelayFan225Spare Low Current Fan2
23IGN Amplifier BIgnition 236Ignition 2 in Wasted Spark
24Rear Screen OnIgnition 333Wire this to COP4 for sequential COP
2512V SW Supply12V—12V Supply from Main Relay
26GroundGround—Power Ground (Not Chassis)

16-way connector

ECU pinOEM functionPnPduino functionArduino pinManufacturer notes
31TachoTacho Out22Tachometer Output 12V
32—CANH—CAN Hi
33Fuel Press SolLow Current 328Spare Low Current 3
34Octane AdjustIdle 210IDLE2 or Spare Hi Current Output
35—Idle 19IDLE1 or Spare Hi Current Output
36ECU Warning LightLow Current 429Spare Low Current 4
37PAS Switch——Not used
38ECU Relay——ECU to activate Main Relay by IG SW
39—VVT11VVT or Spare Hi Current Output
40Waste Gate SolBoost12Boost Solenoid
41—CANL—CAN Lo
42DiagnosticsClutch Switch37Clutch/Launch Switch
43DiagnosticsSensor Ground—Sensor Ground
44—12V Fused Supply—12V Fused Supply to Sensors
45AC SwitchInput 1A8Spare Analog Input 1
46—12V Fused Supply—12V Fused Supply to Sensors

22-way connector

ECU pinOEM functionPnPduino functionArduino pinManufacturer notes
51Start——Not used
52Air TempIntake Air TempA5Intake Air Temperature
53—Flex Sensor22Ethanol Flex Sensor
54Exhaust Temp+Input 5A6Spare Analog Input 5
55—Input 6A12Spare Analog Input 6
56LambdaO2A1O2 from Wideband
57Exhaust Temp-——Not used
58Knock SensorKnock Sensor21Knock Sensor or Digital Hall Input
59—Input 7A13Spare Analog Input 7
60Backup Supply——Not used
61Vref 5V5V output—5V output from ECU
62IGN Switch Supply12V Ignition Switch—IG Switch to activate Main Relay
63Water TempCoolant TempA4Engine Coolant Temperature
64TPSThrottle Position SensorA3Throttle Position Sensor
65Baro Press——Not used
66Road SpeedVehicle Speed Sensor20Vehicle Speed Sensor
67Idle Switch———
68Cam SensorVR2+18Hall Sensor 2 Input
69Crank SensorVR1+19Hall Sensor 1 Input
70Air Flow SensorMAP SensorA0MAP sensor input
71Ground——Ground
72Sensor Ground——Sensor Ground

In this source, CAN high and low are available only with an STM32 processor; ignition and injector assignments depend on the wiring and firing order stated in the table. The source notes an onboard MAP sensor but labels pin 70 as an external MAP input; confirm the actual installed MAP configuration with PnPduino. Position 67 has an OEM idle-switch label but no PnPduino assignment in the table.