PnPduino Mitsubishi EVO3 is a PnPduino programmable engine-management ECU. Manufacturer product information.

Application and identification
Manufacturer identifies the application by a three-plug, 64-position Mitsubishi harness for 4G63T and 4G92/4G93 applications. The product is named EVO3, but the engine and three-plug connection must be checked against the specific vehicle rather than assuming all EVO variants are compatible.
System and wiring
The original trigger can be used; the supplier encourages the supplied 24+1 trigger disc. The original MAF is not used: the ECU’s onboard MAP sensor must be connected. Both high- and low-impedance injectors are listed, and the original resistor box may be removed according to the product instructions. OEM idle servo support and an alternative two-wire idle valve are described.
Connector identification
| Connector | Manufacturer description | Scope |
|---|---|---|
| Vehicle ECU connectors | 3 plugs, 64 positions total | Confirm exact mating loom and pinout; the manufacturer’s numbered schedule is transcribed below. |
The manufacturer’s model-specific connector schedule is transcribed below. Confirm the specific vehicle, connector orientation and hardware revision.
Software and calibration
Uses Speeduino firmware and TunerStudio. A separate wideband controller and a final tune are required.
See the PnPduino manufacturer index.
Model-specific wiring document
The supplier publishes its own model-specific three-connector pinout with OEM and controller functions, wiring notes and colour-coded changed and unused signals. Check the exact engine and loom before using it. Open the PnPduino pinout document. The separate connector-identification table above is a summary; the manufacturer schedule follows below.
EVO3 manufacturer connector schedule
Transcribed from the PnPduino EVO3 pinout, pages 1–4. The original numbers three connectors 1–26, 31–46 and 51–72, for 64 positions total; numbers 27–30 and 47–50 are not part of the depicted connector numbering. Follow the source diagram, which does not specify whether the view is from the ECU face or wire side. Arduino pin numbers are configuration references rather than connector cavity numbers. Blank source cells are shown as a dash, not assumed unused.
26-way connector
| ECU pin | OEM function | PnPduino function | Arduino pin | Manufacturer notes |
|---|---|---|---|---|
| 1 | Injector 1 | Injector 1 | 8 | Wired in Firing order 1-3-4-2 |
| 2 | Injector 3 | Injector 2 | 7 | Wired in Firing order 1-3-4-2 |
| 3 | Radiator Fan | Low Current 1 | 26 | Spare Low Current 1 |
| 4 | Idle Servo 1 | Stepper A1 | — | Stepper Idle Control A |
| 5 | Idle Servo 4 | Stepper B1 | — | Stepper Idle Control B |
| 6 | Sec Air Sol | Low Current 2 | 27 | Spare Low Current 2 |
| 7 | — | Ignition 4 | 34 | Wire this to COP2 for sequential COP |
| 8 | Fuel Pump Relay | Fuel Pump | 23 | Fuel Pump |
| 9 | Alarm Warning Light | — | — | Not used |
| 10 | IGN Amplifier A | Ignition 1 | 35 | Ignition 1 in Wasted Spark |
| 11 | Fan Relay | — | — | Not used |
| 12 | 12V SW Supply | 12V | — | 12V Supply from Main Relay |
| 13 | Ground | Ground | — | Power Ground (Not Chassis) |
| 14 | Injector 2 | Injector 4 | 5 | Wired in Firing order 1-3-4-2 |
| 15 | Injector 4 | Injector 3 | 6 | Wired in Firing order 1-3-4-2 |
| 16 | Radiator Fan | Fan | 24 | Radiator Fan Output |
| 17 | Idle Servo 3 | Stepper A2 | — | Stepper Idle Control A |
| 18 | Idle Servo 6 | Stepper B2 | — | Stepper Idle Control B |
| 19 | Air Flow Reset | Input 3 | A10 | Spare Analog Input 3 |
| 20 | — | Input 4 | A11 | Spare Analog Input 4 |
| 21 | — | Input 2 | A9 | Spare Analog Input 2 |
| 22 | AC Comp Relay | Fan2 | 25 | Spare Low Current Fan2 |
| 23 | IGN Amplifier B | Ignition 2 | 36 | Ignition 2 in Wasted Spark |
| 24 | Rear Screen On | Ignition 3 | 33 | Wire this to COP4 for sequential COP |
| 25 | 12V SW Supply | 12V | — | 12V Supply from Main Relay |
| 26 | Ground | Ground | — | Power Ground (Not Chassis) |
16-way connector
| ECU pin | OEM function | PnPduino function | Arduino pin | Manufacturer notes |
|---|---|---|---|---|
| 31 | Tacho | Tacho Out | 22 | Tachometer Output 12V |
| 32 | — | CANH | — | CAN Hi |
| 33 | Fuel Press Sol | Low Current 3 | 28 | Spare Low Current 3 |
| 34 | Octane Adjust | Idle 2 | 10 | IDLE2 or Spare Hi Current Output |
| 35 | — | Idle 1 | 9 | IDLE1 or Spare Hi Current Output |
| 36 | ECU Warning Light | Low Current 4 | 29 | Spare Low Current 4 |
| 37 | PAS Switch | — | — | Not used |
| 38 | ECU Relay | — | — | ECU to activate Main Relay by IG SW |
| 39 | — | VVT | 11 | VVT or Spare Hi Current Output |
| 40 | Waste Gate Sol | Boost | 12 | Boost Solenoid |
| 41 | — | CANL | — | CAN Lo |
| 42 | Diagnostics | Clutch Switch | 37 | Clutch/Launch Switch |
| 43 | Diagnostics | Sensor Ground | — | Sensor Ground |
| 44 | — | 12V Fused Supply | — | 12V Fused Supply to Sensors |
| 45 | AC Switch | Input 1 | A8 | Spare Analog Input 1 |
| 46 | — | 12V Fused Supply | — | 12V Fused Supply to Sensors |
22-way connector
| ECU pin | OEM function | PnPduino function | Arduino pin | Manufacturer notes |
|---|---|---|---|---|
| 51 | Start | — | — | Not used |
| 52 | Air Temp | Intake Air Temp | A5 | Intake Air Temperature |
| 53 | — | Flex Sensor | 22 | Ethanol Flex Sensor |
| 54 | Exhaust Temp+ | Input 5 | A6 | Spare Analog Input 5 |
| 55 | — | Input 6 | A12 | Spare Analog Input 6 |
| 56 | Lambda | O2 | A1 | O2 from Wideband |
| 57 | Exhaust Temp- | — | — | Not used |
| 58 | Knock Sensor | Knock Sensor | 21 | Knock Sensor or Digital Hall Input |
| 59 | — | Input 7 | A13 | Spare Analog Input 7 |
| 60 | Backup Supply | — | — | Not used |
| 61 | Vref 5V | 5V output | — | 5V output from ECU |
| 62 | IGN Switch Supply | 12V Ignition Switch | — | IG Switch to activate Main Relay |
| 63 | Water Temp | Coolant Temp | A4 | Engine Coolant Temperature |
| 64 | TPS | Throttle Position Sensor | A3 | Throttle Position Sensor |
| 65 | Baro Press | — | — | Not used |
| 66 | Road Speed | Vehicle Speed Sensor | 20 | Vehicle Speed Sensor |
| 67 | Idle Switch | — | — | — |
| 68 | Cam Sensor | VR2+ | 18 | Hall Sensor 2 Input |
| 69 | Crank Sensor | VR1+ | 19 | Hall Sensor 1 Input |
| 70 | Air Flow Sensor | MAP Sensor | A0 | MAP sensor input |
| 71 | Ground | — | — | Ground |
| 72 | Sensor Ground | — | — | Sensor Ground |
In this source, CAN high and low are available only with an STM32 processor; ignition and injector assignments depend on the wiring and firing order stated in the table. The source notes an onboard MAP sensor but labels pin 70 as an external MAP input; confirm the actual installed MAP configuration with PnPduino. Position 67 has an OEM idle-switch label but no PnPduino assignment in the table.