Removed text is struck through; added text is highlighted.
Edelbrock E-Street EFI: The first E-Street system is a carburettor-replacement throttle-body fuel-injection kit with an external ECU, harness and tablet interface. Edelbrock’s original installation manual covers 3600, 3601, 3602 and 3606 packages. These package numbers should be distinguished from E-Street 2 and EZ-Street, whose hardware and software differ.
E-Street installation-manual cover; reproduced with permission from Edelbrock. Edelbrock source; reproduced with permission.
Selection and system layout
Identify the exact ECU, engine and kit part number, intake and throttle, sensor and ignition arrangement. The phone or tablet app is the calibration and monitoring interface, not the ECU. Fuel delivery, return plumbing and auxiliary components depend on the package. Consult the manufacturer documentation for the specific configuration.
Wiring documentation
Use the model-specific Edelbrock source for hardware and wiring. The main harness schedule below is for the original E-Street packages covered by the cited manual; do not substitute another Pro-Flo or E-Street generation.
Original E-Street main harness and ECU connector
Edelbrock’s E-Street installation instructions 63-3600, revision 1, printed page 22 (PDF page 23), show the E1 34-way connector from the harness side for kits 3600, 3601, 3602 and 3606. The manufacturer’s N/C marks refer to the illustrated harness; they do not establish the function or electrical state of a different ECU or harness revision. Wire abbreviations and signal labels follow the drawing.
Separate nine-position communications connector from the same drawing, not the 34-way ECU connector. Crossed-out positions are represented as shown in the illustrated harness.
E5 positionDrawing label1No connect2TXD (PC)3RXD (PC)4No connect5PWR GND6SW +12V — crossed out / not connected on drawing7PWR GND — crossed out / not connected on drawing8No connect9No connect
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Edelbrock E-Street EFI
Edelbrock E-Street EFI: The first E-Street system is a carburettor-replacement throttle-body fuel-injection kit with an external ECU, harness and tablet interface. Edelbrock’s original installation manual covers 3600, 3601, 3602 and 3606 packages. These package numbers should be distinguished from E-Street 2 and EZ-Street, whose hardware and software differ.
E-Street installation-manual cover; reproduced with permission from Edelbrock. Edelbrock source; reproduced with permission.
Selection and system layout
Identify the exact ECU, engine and kit part number, intake and throttle, sensor and ignition arrangement. The phone or tablet app is the calibration and monitoring interface, not the ECU. Fuel delivery, return plumbing and auxiliary components depend on the package. Consult the manufacturer documentation for the specific configuration.
Wiring documentation
Use the model-specific Edelbrock source for hardware and wiring. The main harness schedule below is for the original E-Street packages covered by the cited manual; do not substitute another Pro-Flo or E-Street generation.
Original E-Street main harness and ECU connector
Edelbrock’s E-Street installation instructions 63-3600, revision 1, printed page 22 (PDF page 23), show the E1 34-way connector from the harness side for kits 3600, 3601, 3602 and 3606. The manufacturer’s N/C marks refer to the illustrated harness; they do not establish the function or electrical state of a different ECU or harness revision. Wire abbreviations and signal labels follow the drawing.
E1 position
Signal
Illustrated harness wire
1
INJ A
BLK/GRN
2
12V SW.
ORANGE
3
CURRENT LOOP TXD — N/C
—
4
LAMBDA CR1
DK BLU
5
COOLANT TEMP
YEL/BLK
6
AIR T
TAN
7
AC SWITCH INPUT — N/C
—
8
FUEL PRESSURE
BRWN/YEL
9
MAP
GRN
10
INJ B
BLK/GREY
11
LAMBDA VS+
BLK/ORG
12
LAMBDA IP+
BLK/RED
13
LAMBDA IP−
BLK/YEL
14
RS232 TXD (EFI)
RED/BLU
15
RS232 RXD (EFI)
GRN/WHT
16
TPS
DK BLU
17
RPM SIGNAL (MAG or HALL)
WHT/BLK
18
INJ C
BLK/WHT
19
IAC (COIL 1A)
WHT/VLT
20
IAC (COIL 1B)
WHT/RED
21
IAC (COIL 2A)
WHT/YEL
22
IAC (COIL 2B)
WHT/BLU
23
GND
BLK/WHT/OR
24
GND
BLK
25
VREF
GREY
26
INJ D
BLK/BLU
27
RPM SIGNAL (COIL NEG)
TAN/YEL
28
MSD OUTPUT — N/C
—
29
FAN 1 OUTPUT — N/C
—
30
FAN 2 OUTPUT — N/C
—
31
LAMBDA VH−
VLT
32
FUEL PUMP 12V PWM OUT
RED/WHT
33
GND
BLK/WHT
34
BLUETOOTH ANTENNA — N/C
—
E5 PC communications connector
Separate nine-position communications connector from the same drawing, not the 34-way ECU connector. Crossed-out positions are represented as shown in the illustrated harness.
E5 position
Drawing label
1
No connect
2
TXD (PC)
3
RXD (PC)
4
No connect
5
PWR GND
6
SW +12V — crossed out / not connected on drawing
7
PWR GND — crossed out / not connected on drawing
8
No connect
9
No connect
Revision 2: Edelbrock E-Street EFI
Edelbrock E-Street EFI: The first E-Street system is a carburettor-replacement throttle-body fuel-injection kit with an external ECU, harness and tablet interface. Edelbrock’s original installation manual covers 3600, 3601, 3602 and 3606 packages. These package numbers should be distinguished from E-Street 2 and EZ-Street, whose hardware and software differ.
E-Street installation-manual cover; reproduced with permission from Edelbrock. Edelbrock source; reproduced with permission.
Selection and system layout
Identify the exact ECU, engine and kit part number, intake and throttle, sensor and ignition arrangement. The phone or tablet app is the calibration and monitoring interface, not the ECU. Fuel delivery, return plumbing and auxiliary components depend on the package. Consult the manufacturer documentation for the specific configuration.
Wiring documentation
Use the model-specific Edelbrock source for hardware and wiring. The main harness schedule below is for the original E-Street packages covered by the cited manual; do not substitute another Pro-Flo or E-Street generation.
Original E-Street main harness and ECU connector
Edelbrock’s E-Street installation instructions 63-3600, revision 1, printed page 22 (PDF page 23), show the E1 34-way connector from the harness side for kits 3600, 3601, 3602 and 3606. The manufacturer’s N/C marks refer to the illustrated harness; they do not establish the function or electrical state of a different ECU or harness revision. Wire abbreviations and signal labels follow the drawing.
E1 position
Signal
Illustrated harness wire
1
INJ A
BLK/GRN
2
12V SW.
ORANGE
3
CURRENT LOOP TXD — N/C
—
4
LAMBDA CR1
DK BLU
5
COOLANT TEMP
YEL/BLK
6
AIR T
TAN
7
AC SWITCH INPUT — N/C
—
8
FUEL PRESSURE
BRWN/YEL
9
MAP
GRN
10
INJ B
BLK/GREY
11
LAMBDA VS+
BLK/ORG
12
LAMBDA IP+
BLK/RED
13
LAMBDA IP−
BLK/YEL
14
RS232 TXD (EFI)
RED/BLU
15
RS232 RXD (EFI)
GRN/WHT
16
TPS
DK BLU
17
RPM SIGNAL (MAG or HALL)
WHT/BLK
18
INJ C
BLK/WHT
19
IAC (COIL 1A)
WHT/VLT
20
IAC (COIL 1B)
WHT/RED
21
IAC (COIL 2A)
WHT/YEL
22
IAC (COIL 2B)
WHT/BLU
23
GND
BLK/WHT/OR
24
GND
BLK
25
VREF
GREY
26
INJ D
BLK/BLU
27
RPM SIGNAL (COIL NEG)
TAN/YEL
28
MSD OUTPUT — N/C
—
29
FAN 1 OUTPUT — N/C
—
30
FAN 2 OUTPUT — N/C
—
31
LAMBDA VH−
VLT
32
FUEL PUMP 12V PWM OUT
RED/WHT
33
GND
BLK/WHT
34
BLUETOOTH ANTENNA — N/C
—
E5 PC communications connector
Separate nine-position communications connector from the same drawing, not the 34-way ECU connector. Crossed-out positions are represented as shown in the illustrated harness.