Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
FiTech standalone and throttle-body EFI systems
Applies to
FiTech standalone and throttle-body EFI systems
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

FiTech 30021 Go EFI Classic Black 650HP System is a self-learning carburettor-replacement throttle-body fuel-injection system. FiTech identifies the ECU as a separate, remotely mounted unit; the throttle body has a classic carburettor appearance. The product listing says timing control and forced-induction support are not included.

FiTech’s product image for 30021; kit contents and finish should be checked against the exact part number. Source: FiTech product listing; reproduced with permission.

Identification and fitment

Use the part number to select the correct throttle body, harness, fuel-delivery package and installation instructions. The flange is specified as a four-barrel square bore; some spread-bore manifolds need an adaptor. The product listing identifies the pump as separate from this listed base kit; master kits can differ. FiTech 30021 specifications.

ItemManufacturer listingFiTech model30021Manufacturer maximum power650 HPMounting flange4-barrel square boreECU includedYesThrottle-body finishSatin blackFuel pump included in listed base kitNoTiming control, manufacturer listingNoPower-adder compatible, manufacturer listingNo

Control and installation

FiTech describes self-learning fuel adjustment after initial setup, using an oxygen-sensor input. A correctly specified high-pressure EFI fuel system, sensors and ignition reference are required; verify the fuel-system and distributor configuration against the model manual. A carburettor-replacement throttle body does not automatically provide every ignition or transmission-control function.

Wiring documentation

Use the FiTech installation documentation for the exact system and revision. A complete numbered ECU connector schedule has not yet been verified for this page; do not substitute the wiring of a visually similar kit.

Harness A: customer connections

FiTech’s 30021 installation manual, page 5, figure 15, identifies these four customer-wired leads by colour. This is the full set in that wire chart, not a numbered ECU cavity pinout; the manufacturer does not assign ECU connector positions in the chart. The system also has separately labelled connectors for its sensors, injector sub-harness and handheld controller.

Harness leadManufacturer-described connectionRedFuel-pump circuit: the supplied lead provides +12 V to the pump positive terminal; FiTech says no additional relay is required for this harness.OrangeMain power on/off input: switched +12 V present during both key-on and cranking and absent when off.TanTachometer/RPM input. Connect as specified for the selected coil, HEI distributor or CDI tach output in the model’s wiring diagram.GreyFan 1 control, to the ground-trigger terminal of the fan relay.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: FiTech 30021 Go EFI Classic Black 650HP System

FiTech 30021 Go EFI Classic Black 650HP System is a self-learning carburettor-replacement throttle-body fuel-injection system. FiTech identifies the ECU as a separate, remotely mounted unit; the throttle body has a classic carburettor appearance. The product listing says timing control and forced-induction support are not included.

FiTech 30021 throttle-body EFI
FiTech’s product image for 30021; kit contents and finish should be checked against the exact part number. Source: FiTech product listing; reproduced with permission.

Identification and fitment

Use the part number to select the correct throttle body, harness, fuel-delivery package and installation instructions. The flange is specified as a four-barrel square bore; some spread-bore manifolds need an adaptor. The product listing identifies the pump as separate from this listed base kit; master kits can differ. FiTech 30021 specifications.

ItemManufacturer listing
FiTech model30021
Manufacturer maximum power650 HP
Mounting flange4-barrel square bore
ECU includedYes
Throttle-body finishSatin black
Fuel pump included in listed base kitNo
Timing control, manufacturer listingNo
Power-adder compatible, manufacturer listingNo

Control and installation

FiTech describes self-learning fuel adjustment after initial setup, using an oxygen-sensor input. A correctly specified high-pressure EFI fuel system, sensors and ignition reference are required; verify the fuel-system and distributor configuration against the model manual. A carburettor-replacement throttle body does not automatically provide every ignition or transmission-control function.

Wiring documentation

Use the FiTech installation documentation for the exact system and revision. A complete numbered ECU connector schedule has not yet been verified for this page; do not substitute the wiring of a visually similar kit.

Harness A: customer connections

FiTech’s 30021 installation manual, page 5, figure 15, identifies these four customer-wired leads by colour. This is the full set in that wire chart, not a numbered ECU cavity pinout; the manufacturer does not assign ECU connector positions in the chart. The system also has separately labelled connectors for its sensors, injector sub-harness and handheld controller.

Harness leadManufacturer-described connection
RedFuel-pump circuit: the supplied lead provides +12 V to the pump positive terminal; FiTech says no additional relay is required for this harness.
OrangeMain power on/off input: switched +12 V present during both key-on and cranking and absent when off.
TanTachometer/RPM input. Connect as specified for the selected coil, HEI distributor or CDI tach output in the model’s wiring diagram.
GreyFan 1 control, to the ground-trigger terminal of the fan relay.
Revision 2: FiTech 30021 Go EFI Classic Black 650HP System

FiTech 30021 Go EFI Classic Black 650HP System is a self-learning carburettor-replacement throttle-body fuel-injection system. FiTech identifies the ECU as a separate, remotely mounted unit; the throttle body has a classic carburettor appearance. The product listing says timing control and forced-induction support are not included.

FiTech 30021 throttle-body EFI
FiTech’s product image for 30021; kit contents and finish should be checked against the exact part number. Source: FiTech product listing; reproduced with permission.

Identification and fitment

Use the part number to select the correct throttle body, harness, fuel-delivery package and installation instructions. The flange is specified as a four-barrel square bore; some spread-bore manifolds need an adaptor. The product listing identifies the pump as separate from this listed base kit; master kits can differ. FiTech 30021 specifications.

ItemManufacturer listing
FiTech model30021
Manufacturer maximum power650 HP
Mounting flange4-barrel square bore
ECU includedYes
Throttle-body finishSatin black
Fuel pump included in listed base kitNo
Timing control, manufacturer listingNo
Power-adder compatible, manufacturer listingNo

Control and installation

FiTech describes self-learning fuel adjustment after initial setup, using an oxygen-sensor input. A correctly specified high-pressure EFI fuel system, sensors and ignition reference are required; verify the fuel-system and distributor configuration against the model manual. A carburettor-replacement throttle body does not automatically provide every ignition or transmission-control function.

Wiring documentation

Use the FiTech installation documentation for the exact system and revision. A complete numbered ECU connector schedule has not yet been verified for this page; do not substitute the wiring of a visually similar kit.

Harness A: customer connections

FiTech’s 30021 installation manual, page 5, figure 15, identifies these four customer-wired leads by colour. This is the full set in that wire chart, not a numbered ECU cavity pinout; the manufacturer does not assign ECU connector positions in the chart. The system also has separately labelled connectors for its sensors, injector sub-harness and handheld controller.

Harness leadManufacturer-described connection
RedFuel-pump circuit: the supplied lead provides +12 V to the pump positive terminal; FiTech says no additional relay is required for this harness.
OrangeMain power on/off input: switched +12 V present during both key-on and cranking and absent when off.
TanTachometer/RPM input. Connect as specified for the selected coil, HEI distributor or CDI tach output in the model’s wiring diagram.
GreyFan 1 control, to the ground-trigger terminal of the fan relay.