Page organisation in this revision
- Page type
- Technical article
- Subject
- ABS / DSC
- Parent
- Hondata Traction Control module
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Hondata
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
This reference reproduces the wire-side connector layouts and harness colours in the Hondata traction control connector guide. The maker shows the connector from the wire side in two rows of ten positions, but does not label physical cavity numbers in this diagram: the rows below preserve its left-to-right order and should not be treated as manufacturer pin numbering. Confirm connector keying and orientation against the original guide.
Wire-side layout, left to right
RowFunctions in manufacturer diagram orderTopGND+12 VOut1Out2Out3Out4LF+RF+LR+RR+BottomGND+12 VSerial OutCAN LCAN HECULF−RF−LR−RR−
LF/RF/LR/RR mean left-front/right-front/left-rear/right-rear wheel-speed inputs. The ECU connection is an analogue over-slip signal to a compatible engine ECU. Out1–Out4 are 3.3 V pulse outputs with 5 mA maximum load; the maker says not to connect them to power or ground. The serial output is 0 V idle, 3.3 V active. The labelled GND and +12 V positions appear twice in the source diagram; wire colours are given there for one of each, so do not assume the other has the same harness colour.
Documented harness-colour revisions
FunctionMarch–October 2012 diagramOctober 2012 onward diagramGNDBlackBlack+12 VRedRedECUOrangeOrangeLF+BlueBlueLF−Light blueYellowRF+GreenGreenRF−Light greenWhiteLR+BrownBrownLR−TanGreyRR+VioletPurpleRR−PinkPink
Hondata labels both date ranges with October 2012 as a boundary, so identify the actual harness rather than relying on the date alone. Switching ground and ECU output can damage the module. The connector guide specifies ECU ground close to the ECU, not chassis or ECU case; consult the separate Hondata quickstart for its stated ECU-master-ground alternative and current installation instructions.
Supplier-documented application examples
Hondata's sensor-wiring examples include 1996–2000 Civic, 2002–2006 Acura RSX, 2000–2005 and 2006–2009 S2000, and 2006–2011 Civic Si. These identify integration examples, not a guarantee for every market or ABS variant. Hondata identifies the 2006–2011 Civic Si example as active-sensor ABS and warns that incorrect wiring can disable ABS. Its guide notes similar colours occur more than once and requires the exact vehicle wiring information. See the manufacturer connector and application guide and sensor-type-specific installation notes.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Hondata traction control module wire-side connector layout
This reference reproduces the wire-side connector layouts and harness colours in the Hondata traction control connector guide. The maker shows the connector from the wire side in two rows of ten positions, but does not label physical cavity numbers in this diagram: the rows below preserve its left-to-right order and should not be treated as manufacturer pin numbering. Confirm connector keying and orientation against the original guide.
Wire-side layout, left to right
| Row | Functions in manufacturer diagram order |
|---|
| Top | GND | +12 V | Out1 | Out2 | Out3 | Out4 | LF+ | RF+ | LR+ | RR+ |
|---|
| Bottom | GND | +12 V | Serial Out | CAN L | CAN H | ECU | LF− | RF− | LR− | RR− |
|---|
LF/RF/LR/RR mean left-front/right-front/left-rear/right-rear wheel-speed inputs. The ECU connection is an analogue over-slip signal to a compatible engine ECU. Out1–Out4 are 3.3 V pulse outputs with 5 mA maximum load; the maker says not to connect them to power or ground. The serial output is 0 V idle, 3.3 V active. The labelled GND and +12 V positions appear twice in the source diagram; wire colours are given there for one of each, so do not assume the other has the same harness colour.
Documented harness-colour revisions
| Function | March–October 2012 diagram | October 2012 onward diagram |
|---|
| GND | Black | Black |
| +12 V | Red | Red |
| ECU | Orange | Orange |
| LF+ | Blue | Blue |
| LF− | Light blue | Yellow |
| RF+ | Green | Green |
| RF− | Light green | White |
| LR+ | Brown | Brown |
| LR− | Tan | Grey |
| RR+ | Violet | Purple |
| RR− | Pink | Pink |
Hondata labels both date ranges with October 2012 as a boundary, so identify the actual harness rather than relying on the date alone. Switching ground and ECU output can damage the module. The connector guide specifies ECU ground close to the ECU, not chassis or ECU case; consult the separate Hondata quickstart for its stated ECU-master-ground alternative and current installation instructions.
Supplier-documented application examples
Hondata's sensor-wiring examples include 1996–2000 Civic, 2002–2006 Acura RSX, 2000–2005 and 2006–2009 S2000, and 2006–2011 Civic Si. These identify integration examples, not a guarantee for every market or ABS variant. Hondata identifies the 2006–2011 Civic Si example as active-sensor ABS and warns that incorrect wiring can disable ABS. Its guide notes similar colours occur more than once and requires the exact vehicle wiring information. See the manufacturer connector and application guide and sensor-type-specific installation notes.
Revision 1: Hondata traction control module wire-side connector layout
This reference reproduces the wire-side connector layouts and harness colours in the Hondata traction control connector guide. The maker shows the connector from the wire side in two rows of ten positions, but does not label physical cavity numbers in this diagram: the rows below preserve its left-to-right order and should not be treated as manufacturer pin numbering. Confirm connector keying and orientation against the original guide.
Wire-side layout, left to right
| Row | Functions in manufacturer diagram order |
|---|
| Top | GND | +12 V | Out1 | Out2 | Out3 | Out4 | LF+ | RF+ | LR+ | RR+ |
|---|
| Bottom | GND | +12 V | Serial Out | CAN L | CAN H | ECU | LF− | RF− | LR− | RR− |
|---|
LF/RF/LR/RR mean left-front/right-front/left-rear/right-rear wheel-speed inputs. The ECU connection is an analogue over-slip signal to a compatible engine ECU. Out1–Out4 are 3.3 V pulse outputs with 5 mA maximum load; the maker says not to connect them to power or ground. The serial output is 0 V idle, 3.3 V active. The labelled GND and +12 V positions appear twice in the source diagram; wire colours are given there for one of each, so do not assume the other has the same harness colour.
Documented harness-colour revisions
| Function | March–October 2012 diagram | October 2012 onward diagram |
|---|
| GND | Black | Black |
| +12 V | Red | Red |
| ECU | Orange | Orange |
| LF+ | Blue | Blue |
| LF− | Light blue | Yellow |
| RF+ | Green | Green |
| RF− | Light green | White |
| LR+ | Brown | Brown |
| LR− | Tan | Grey |
| RR+ | Violet | Purple |
| RR− | Pink | Pink |
Hondata labels both date ranges with October 2012 as a boundary, so identify the actual harness rather than relying on the date alone. Switching ground and ECU output can damage the module. The connector guide specifies ECU ground close to the ECU, not chassis or ECU case; consult the separate Hondata quickstart for its stated ECU-master-ground alternative and current installation instructions.
Supplier-documented application examples
Hondata's sensor-wiring examples include 1996–2000 Civic, 2002–2006 Acura RSX, 2000–2005 and 2006–2009 S2000, and 2006–2011 Civic Si. These identify integration examples, not a guarantee for every market or ABS variant. Hondata identifies the 2006–2011 Civic Si example as active-sensor ABS and warns that incorrect wiring can disable ABS. Its guide notes similar colours occur more than once and requires the exact vehicle wiring information. See the manufacturer connector and application guide and sensor-type-specific installation notes.