Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Edelbrock standalone and retrofit EFI systems
Applies to
Edelbrock standalone and retrofit EFI systems
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

Edelbrock E-Street EFI: The first E-Street system is a carburettor-replacement throttle-body fuel-injection kit with an external ECU, harness and tablet interface. Edelbrock’s original installation manual covers 3600, 3601, 3602 and 3606 packages. These package numbers should be distinguished from E-Street 2 and EZ-Street, whose hardware and software differ.

E-Street installation-manual cover; reproduced with permission from Edelbrock. Edelbrock source; reproduced with permission.

Selection and system layout

Identify the exact ECU, engine and kit part number, intake and throttle, sensor and ignition arrangement. The phone or tablet app is the calibration and monitoring interface, not the ECU. Fuel delivery, return plumbing and auxiliary components depend on the package. Consult the manufacturer documentation for the specific configuration.

Wiring documentation

Use the model-specific Edelbrock source for hardware and wiring. The main harness schedule below is for the original E-Street packages covered by the cited manual; do not substitute another Pro-Flo or E-Street generation.Original E-Street main harness and ECU connectorEdelbrock’s E-Street installation instructions 63-3600, revision 1, printed page 22 (PDF page 23), show the E1 34-way connector from the harness side for kits 3600, 3601, 3602 and 3606. The manufacturer’s N/C marks refer to the illustrated harness; they do not establish the function or electrical state of a different ECU or harness revision. Wire abbreviations and signal labels follow the drawing.E1 positionSignalIllustrated harness wire1INJ ABLK/GRN212V SW.ORANGE3CURRENT LOOP TXD — N/C—4LAMBDA CR1DK BLU5COOLANT TEMPYEL/BLK6AIR TTAN7AC SWITCH INPUT — N/C—8FUEL PRESSUREBRWN/YEL9MAPGRN10INJ BBLK/GREY11LAMBDA VS+BLK/ORG12LAMBDA IP+BLK/RED13LAMBDA IP−BLK/YEL14RS232 TXD (EFI)RED/BLU15RS232 RXD (EFI)GRN/WHT16TPSDK BLU17RPM SIGNAL (MAG or HALL)WHT/BLK18INJ CBLK/WHT19IAC (COIL 1A)WHT/VLT20IAC (COIL 1B)WHT/RED21IAC (COIL 2A)WHT/YEL22IAC (COIL 2B)WHT/BLU23GNDBLK/WHT/OR24GNDBLK25VREFGREY26INJ DBLK/BLU27RPM SIGNAL (COIL NEG)TAN/YEL28MSD OUTPUT — N/C—29FAN 1 OUTPUT — N/C—30FAN 2 OUTPUT — N/C—31LAMBDA VH−VLT32FUEL PUMP 12V PWM OUTRED/WHT33GNDBLK/WHT34BLUETOOTH ANTENNA — N/C—E5 PC communications connectorSeparate nine-position communications connector from the same drawing, not the 34-way ECU connector. Crossed-out positions are represented as shown in the illustrated harness.E5 positionDrawing label1No connect2TXD (PC)3RXD (PC)4No connect5PWR GND6SW +12V — crossed out / not connected on drawing7PWR GND — crossed out / not connected on drawing8No connect9No connectUse the model-specific Edelbrock source for hardware and wiring. A complete numbered ECU connector table has not yet been verified for this page; do not substitute the assignment of another Pro-Flo or E-Street system.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Edelbrock E-Street EFI

Edelbrock E-Street EFI: The first E-Street system is a carburettor-replacement throttle-body fuel-injection kit with an external ECU, harness and tablet interface. Edelbrock’s original installation manual covers 3600, 3601, 3602 and 3606 packages. These package numbers should be distinguished from E-Street 2 and EZ-Street, whose hardware and software differ.

Edelbrock E-Street EFI manufacturer illustration
E-Street installation-manual cover; reproduced with permission from Edelbrock. Edelbrock source; reproduced with permission.

Selection and system layout

Identify the exact ECU, engine and kit part number, intake and throttle, sensor and ignition arrangement. The phone or tablet app is the calibration and monitoring interface, not the ECU. Fuel delivery, return plumbing and auxiliary components depend on the package. Consult the manufacturer documentation for the specific configuration.

Wiring documentation

Use the model-specific Edelbrock source for hardware and wiring. A complete numbered ECU connector table has not yet been verified for this page; do not substitute the assignment of another Pro-Flo or E-Street system.

Revision 2: Edelbrock E-Street EFI

Edelbrock E-Street EFI: The first E-Street system is a carburettor-replacement throttle-body fuel-injection kit with an external ECU, harness and tablet interface. Edelbrock’s original installation manual covers 3600, 3601, 3602 and 3606 packages. These package numbers should be distinguished from E-Street 2 and EZ-Street, whose hardware and software differ.

Edelbrock E-Street EFI manufacturer illustration
E-Street installation-manual cover; reproduced with permission from Edelbrock. Edelbrock source; reproduced with permission.

Selection and system layout

Identify the exact ECU, engine and kit part number, intake and throttle, sensor and ignition arrangement. The phone or tablet app is the calibration and monitoring interface, not the ECU. Fuel delivery, return plumbing and auxiliary components depend on the package. Consult the manufacturer documentation for the specific configuration.

Wiring documentation

Use the model-specific Edelbrock source for hardware and wiring. The main harness schedule below is for the original E-Street packages covered by the cited manual; do not substitute another Pro-Flo or E-Street generation.

Original E-Street main harness and ECU connector

Edelbrock’s E-Street installation instructions 63-3600, revision 1, printed page 22 (PDF page 23), show the E1 34-way connector from the harness side for kits 3600, 3601, 3602 and 3606. The manufacturer’s N/C marks refer to the illustrated harness; they do not establish the function or electrical state of a different ECU or harness revision. Wire abbreviations and signal labels follow the drawing.

E1 positionSignalIllustrated harness wire
1INJ ABLK/GRN
212V SW.ORANGE
3CURRENT LOOP TXD — N/C—
4LAMBDA CR1DK BLU
5COOLANT TEMPYEL/BLK
6AIR TTAN
7AC SWITCH INPUT — N/C—
8FUEL PRESSUREBRWN/YEL
9MAPGRN
10INJ BBLK/GREY
11LAMBDA VS+BLK/ORG
12LAMBDA IP+BLK/RED
13LAMBDA IP−BLK/YEL
14RS232 TXD (EFI)RED/BLU
15RS232 RXD (EFI)GRN/WHT
16TPSDK BLU
17RPM SIGNAL (MAG or HALL)WHT/BLK
18INJ CBLK/WHT
19IAC (COIL 1A)WHT/VLT
20IAC (COIL 1B)WHT/RED
21IAC (COIL 2A)WHT/YEL
22IAC (COIL 2B)WHT/BLU
23GNDBLK/WHT/OR
24GNDBLK
25VREFGREY
26INJ DBLK/BLU
27RPM SIGNAL (COIL NEG)TAN/YEL
28MSD OUTPUT — N/C—
29FAN 1 OUTPUT — N/C—
30FAN 2 OUTPUT — N/C—
31LAMBDA VH−VLT
32FUEL PUMP 12V PWM OUTRED/WHT
33GNDBLK/WHT
34BLUETOOTH ANTENNA — N/C—

E5 PC communications connector

Separate nine-position communications connector from the same drawing, not the 34-way ECU connector. Crossed-out positions are represented as shown in the illustrated harness.

E5 positionDrawing label
1No connect
2TXD (PC)
3RXD (PC)
4No connect
5PWR GND
6SW +12V — crossed out / not connected on drawing
7PWR GND — crossed out / not connected on drawing
8No connect
9No connect