Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Haltech standalone ECUs
Applies to
Haltech standalone ECUs
Tool groups
None
Manufacturers
None

Haltech Nexus Plug-in Honda EP3 2001–2005 and DC5 2002–2004 is a vehicle-specific, direct plug-in programmable ECU, Haltech part HT-231001, that replaces the original engine ECU. Haltech product listing.

Haltech Nexus Honda plug-in ECU
Haltech Nexus Honda plug-in ECU. The same manufacturer photograph appears on the EP3 and DC5 product listings; confirm the part number and connector application. Haltech product photograph, reproduced with permission.

Applications and identification

The HT-231001 is listed by Haltech for the 2001–2005 Honda Civic EP3 and 2002–2004 Honda Integra / Acura RSX DC5, manual transmission only. The manufacturer says a K24A swap is supported when the original vehicle engine harness is retained for the correct pin assignments.

Haltech says the original four-wire wideband sensor is not supported and calls for an LSU 4.9 or NTK sensor via the auxiliary connector. The ECU has an onboard 4-bar MAP sensor; its vacuum connection must be connected if used. Manufacturer details are in the Honda Nexus installation guide.

Vehicle connector assignments

These 86 assignments reproduce the Haltech 231001 quick-start guide, PDF page 7, manufacturer document hosted by a retailer. View is the ECU pin side; Haltech marks vehicle connectors C and D unused. Use the chart for this exact part number; calibratable outputs depend on setup.

The manufacturer schedule lists both E1 and E10 as DPO 11 fuel-pump relay output; verify the vehicle harness and the current manufacturer documentation if using these circuits.

Vehicle connector A

PinECU connectionManufacturer function
A1UnusedNo connection
A2+12V ECU powerECU switched power supply
A3+12V ECU powerECU switched power supply
A4Power groundBattery ground
A5Power groundBattery ground
A6UnusedNo connection
A7TriggerCrank sensor
A8AVI 12Dual intake runner position input
A9Knock 1Knock sensor
A10Sensor groundSensor ground
A11Sensor groundSensor ground
A12DPO 6Idle control
A13UnusedNo connection
A14UnusedNo connection
A15AVI 10Throttle position sensor
A16UnusedNo connection
A17UnusedNo connection
A18SPI 5Vehicle speed sensor
A19AVI 9MAP sensor
A20+5V DC+5V sensor supply
A21+5V DC+5V sensor supply
A22UnusedNo connection
A23Power groundBattery ground
A24Power groundBattery ground
A25SPI 6Intake cam sensor
A26HomeExhaust cam sensor
A27Ignition 4Ignition output for cylinder 4
A28Ignition 3Ignition output for cylinder 3
A29Ignition 2Ignition output for cylinder 2
A30Ignition 1Ignition output for cylinder 1
A31UnusedNo connection

Vehicle connector B

PinECU connectionManufacturer function
B1HBO 3Intake VTC solenoid control
B2Injector 4Injector output for cylinder 4
B3Injector 3Injector output for cylinder 3
B4Injector 2Injector output for cylinder 2
B5Injector 1Injector output for cylinder 1
B6DPO 10Thermofan relay output
B7DPO 8Reverse lockout solenoid
B8AVI 8Coolant temperature sensor
B9AVI 13Oil pressure switch (VTEC)
B10AVI 16Alternator L
B11UnusedNo connection
B12UnusedNo connection
B13AVI 17Alternator FR
B14UnusedNo connection
B15HBO 4VTEC solenoid
B16UnusedNo connection
B17AVI 7Intake air temperature sensor
B18DPO 17Alternator control output
B19UnusedNo connection
B20UnusedNo connection
B21DPO 12Evap purge valve solenoid
B22DPO 5Dual intake runner system (IMRC)
B23Power groundBattery ground
B24UnusedNo connection

Vehicle connector E

PinECU connectionManufacturer function
E1DPO 11Fuel pump relay output
E2AVI 6Narrowband O2 sensor input
E3Power groundImmobilizer ground
E4Sensor groundSensor ground
E5+5V DC+5V sensor supply
E6DPO 7O2 sensor heater output
E7ECREngine control relay output
E8UnusedNo connection
E9Ign SW InputIgnition switch
E10DPO 11Fuel pump relay output
E11UnusedNo connection
E12UnusedNo connection
E13UnusedNo connection
E14AVI 14Fuel tank pressure sensor
E15AVI 15Electrical load detector input
E16AVI 11Power steering switch input
E17UnusedNo connection
E18DPO 14A/C relay output
E19UnusedNo connection
E20DPO 16Evap bypass solenoid
E21DPO 13Evap vent shut valve
E22AVI 5Brake pedal switch input
E23UnusedNo connection
E24Multiplex serial commsMultiplex serial communications
E25UnusedNo connection
E26DPO 15Tachometer output
E27Immobilizer commsImmobilizer serial communications
E28UnusedNo connection
E29UnusedNo connection
E30UnusedNo connection
E31DPO 9Check engine light

26-pin auxiliary connector

The following table is the ECU auxiliary connector, pin-side view, from the same manufacturer guide, page 8. It is distinct from the vehicle ECU connectors above. Haltech states switched 12 V from the onboard CAN and auxiliary connectors is limited to 8 A total across the three pins.

PinHaltech connectionHarness colour
1DPO 1Violet / Blue
2DPO 3Violet / Red
3Aux power (12V switched)Red
4Sensor groundBlack / White
5SPI 1Gray / Brown
6SPI 3Gray / Orange
7HBO 1Brown / Black
8AVI 1White
9AVI 3White / Gray
10Sensor groundBlack / White
11WBI 1 Heater +Gray
12WBI 1 InputYellow
13WBI 1 PumpRed
14DPO 2Violet / Brown
15DPO 4Violet / Orange
16Aux power (12V switched)Red
17Sensor +5V DCOrange
18SPI 2Gray / Red
19SPI 4Gray / Yellow
20HBO 2Brown / Red
21AVI 2White / Yellow
22AVI 4White / Violet
23Sensor +5V DCOrange
24WBI 1 NernstBlack
25WBI 1 Heater -White
26WBI 1 CalGreen

Software

Nexus Software Programmer (NSP) configures and tunes the ECU; USB-C and optional Wi-Fi communication are described in Haltech’s installation guide. The setup wizard provides a starting configuration and the engine requires appropriate tuning.