Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 4 to revision 4

Removed text is struck through; added text is highlighted.

Volvo Trucks I-Shift is a family of electronically controlled automated manual transmissions for commercial vehicles. Volvo describes the original I-Shift as based on a non-synchronised manual-type gearbox; the family later acquired other versions, including an I-Shift Dual Clutch. The single-clutch examples below are not a universal procedure for the dual-clutch model, every generation or another Volvo vehicle. Identify the truck and market, transmission model, TECU hardware and software, clutch and service history. Volvo Trucks: I-Shift generations.

System and diagnostic starting point

In the North American Volvo service example described below, the I-Shift/mDRIVE automated manual uses a push-type clutch rather than the torque converter of a conventional automatic. The controller coordinates the clutch, gearbox and engine. Pneumatic supply and electronic communications can both affect operation. Match the truck, transmission variant and software before interpreting a warning or selecting a procedure. Volvo: clutch protection message; Volvo: clutch control actuator service program.

Volvo's 2022 I-Shift diagnostic advice calls for an interview, reproducing the complaint under the relevant conditions and recording all active and inactive faults and occurrence counts. It warns against programming the transmission ECU early in the diagnosis unless directed, since useful fault information and diagnostic or calibration access can be lost. If the problem persists without codes, it points to the applicable symptom-based diagnostic plan. This is a diagnostic sequence, not a blanket instruction to clear fault memory. Volvo: do not program the TECU unless instructed.

Fault and symptom examples

Documented exampleWhat the source saysDiagnostic boundary Clutch protection message; P1060 74 / PPID 50 FMI 11Volvo's North American service note describes a warning associated with prolonged clutch slip while the vehicle moves very little, such as holding on a gradient with the clutch slipping. In that note, the message alone is intended to discourage the operating condition; it asks for workshop investigation when associated with other clutch-control codes.Do not assume every clutch warning means worn friction material, or that the absence of another code proves a different symptom harmless. Use the exact current instructions and applicable fault context. Volvo clutch-protection note. Clutch actuator air-loss warning on early VN/VTVolvo service program SP 413-001 describes software for specified I-Shift-equipped vehicles before 15 December 2009. Its yellow warning denotes an air leak the documented TECU strategy can compensate for, with idle driving and Eco-Roll inhibited; a larger leak can cause a red warning and buzzer with neutral selection or engine shutdown when stopped.This is a historical programme and its described software behaviour, not a diagnosis or recall applicability for all I-Shift trucks. Confirm VIN, software, warnings and current repair data. Volvo SP 413-001. Speed-sensor related MID 130 PID 160 FMI 1/2 after parts workVolvo describes a version-C transmission example where mixing generation-C and generation-D TECU, harness/speed-sensor and sensor-wheel hardware may lead to these faults. Its service note points to a specific mixed-components bulletin.These codes can require the manufacturer fault tree and component identification; they are not proof that every sensor itself is defective or that a conversion kit fits every unit. Volvo: mixed I-Shift components. Hill-start assist holds on level ground after TECU programming or replacementVolvo describes reset or missing inclination-sensor calibration as a possible cause on listed AMT-C, AMT-D and AMT-F trucks; its calibration sequences differ by transmission.Do not apply one generation's sequence to another or assume every unwanted brake hold is this issue. Volvo: inclination-sensor calibration. Clutch/transmission calibration fails immediately after clutch replacement or programmingVolvo has a service note for AMT-D/F involving a missing or invalid X1 value and P1052-54 or other errors during calibration.The note's vehicle, equipment and diagnostic circumstances must be matched. The failure alone does not establish that the clutch or TECU needs replacing; use the current guided support process. Volvo: X1 and failed calibration.

Brake signal and calibration cases

The US NHTSA investigation PE13-002 closure report describes Volvo Trucks North America recall 13V268 / RVXX1303 for a defined population of model-year 2007–2014 VAH, VHD, VNL, VNM and VT trucks with the specified automated transmission. In the documented circumstances, loss of a primary brake-applied signal without the redundant switch could prevent the clutch from disengaging at low speed, with a risk of extended stopping or unintended movement. Check the actual VIN and current recall status with Volvo and use the current brake-signal and transmission diagnostic plan; this history does not establish the cause of every clutch-drag complaint.

Separately, Volvo's 2018 AMT-F Tech Tool note documents a calibration routine that could stop at 33% because the historical tool attempted to calibrate a crawler section that was not installed. It identifies a tool-version correction and different procedures according to what had been replaced. Match the truck, tool version and exact error before treating an aborted calibration as evidence of a defective gearbox; consult current Volvo service information.

After TECU programming: P1061-54. Volvo’s AMT-F I-Shift/mDRIVE calibration note describes a clutch-cylinder slip-point calibration fault and transmission-check message that may appear after programming. In the documented AMT-F situation, valid existing clutch-position and shifter calibrations can be transferred by the diagnostic tool, while the slip point is handled separately. A blank replacement TECU has different requirements; older AMT-C/D procedures also differ. Record the full code and programming history and follow the current generation-specific Volvo/Mack procedure before assuming a failed clutch or controller. The note describes a specific post-programming state, not an explanation for every P1061-54 in service.

Practical evidence and service

Record the exact complaint, warning text, gear, load, gradient, temperature and whether it occurs when starting, engaging drive, taking up the clutch or changing a particular gear. Preserve fault data and prior work before clearing or programming. Check air supply, electrical supply, relevant communications and clutch/gear feedback using the model's current guided test, and distinguish a driver-information message from a verified system fault. Do not bypass protection or assume that a pressure, speed or actuator fault identifies a single failed part. Where a power take-off is fitted, establish its command and engagement state. In Volvo's documented transmission-mounted PTO example, engaging drive releases and then re-engages the clutch; shifting is restricted while that PTO is active. This behaviour is configuration-specific. Volvo Trucks: I-Shift PTO FAQs. Perform programming, clutch/gear learning and sensor calibration only when the current procedure calls for them, with the specified diagnostic equipment and safety conditions. Follow the model-specific recovery and verification procedures; actuators can move and air systems can remain pressurised.

See Mack mDRIVE faults and diagnosis for related commercial-vehicle cases with their own applicability, Eaton UltraShift PLUS diagnosis for a different commercial-vehicle architecture and the electronic gearbox index.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 4: Volvo Trucks I-Shift automated manual operation and diagnosis

Volvo Trucks I-Shift is a family of electronically controlled automated manual transmissions for commercial vehicles. Volvo describes the original I-Shift as based on a non-synchronised manual-type gearbox; the family later acquired other versions, including an I-Shift Dual Clutch. The single-clutch examples below are not a universal procedure for the dual-clutch model, every generation or another Volvo vehicle. Identify the truck and market, transmission model, TECU hardware and software, clutch and service history. Volvo Trucks: I-Shift generations.

System and diagnostic starting point

In the North American Volvo service example described below, the I-Shift/mDRIVE automated manual uses a push-type clutch rather than the torque converter of a conventional automatic. The controller coordinates the clutch, gearbox and engine. Pneumatic supply and electronic communications can both affect operation. Match the truck, transmission variant and software before interpreting a warning or selecting a procedure. Volvo: clutch protection message; Volvo: clutch control actuator service program.

Volvo's 2022 I-Shift diagnostic advice calls for an interview, reproducing the complaint under the relevant conditions and recording all active and inactive faults and occurrence counts. It warns against programming the transmission ECU early in the diagnosis unless directed, since useful fault information and diagnostic or calibration access can be lost. If the problem persists without codes, it points to the applicable symptom-based diagnostic plan. This is a diagnostic sequence, not a blanket instruction to clear fault memory. Volvo: do not program the TECU unless instructed.

Fault and symptom examples

Documented exampleWhat the source saysDiagnostic boundary
Clutch protection message; P1060 74 / PPID 50 FMI 11Volvo's North American service note describes a warning associated with prolonged clutch slip while the vehicle moves very little, such as holding on a gradient with the clutch slipping. In that note, the message alone is intended to discourage the operating condition; it asks for workshop investigation when associated with other clutch-control codes.Do not assume every clutch warning means worn friction material, or that the absence of another code proves a different symptom harmless. Use the exact current instructions and applicable fault context. Volvo clutch-protection note.
Clutch actuator air-loss warning on early VN/VTVolvo service program SP 413-001 describes software for specified I-Shift-equipped vehicles before 15 December 2009. Its yellow warning denotes an air leak the documented TECU strategy can compensate for, with idle driving and Eco-Roll inhibited; a larger leak can cause a red warning and buzzer with neutral selection or engine shutdown when stopped.This is a historical programme and its described software behaviour, not a diagnosis or recall applicability for all I-Shift trucks. Confirm VIN, software, warnings and current repair data. Volvo SP 413-001.
Speed-sensor related MID 130 PID 160 FMI 1/2 after parts workVolvo describes a version-C transmission example where mixing generation-C and generation-D TECU, harness/speed-sensor and sensor-wheel hardware may lead to these faults. Its service note points to a specific mixed-components bulletin.These codes can require the manufacturer fault tree and component identification; they are not proof that every sensor itself is defective or that a conversion kit fits every unit. Volvo: mixed I-Shift components.
Hill-start assist holds on level ground after TECU programming or replacementVolvo describes reset or missing inclination-sensor calibration as a possible cause on listed AMT-C, AMT-D and AMT-F trucks; its calibration sequences differ by transmission.Do not apply one generation's sequence to another or assume every unwanted brake hold is this issue. Volvo: inclination-sensor calibration.
Clutch/transmission calibration fails immediately after clutch replacement or programmingVolvo has a service note for AMT-D/F involving a missing or invalid X1 value and P1052-54 or other errors during calibration.The note's vehicle, equipment and diagnostic circumstances must be matched. The failure alone does not establish that the clutch or TECU needs replacing; use the current guided support process. Volvo: X1 and failed calibration.

Brake signal and calibration cases

The US NHTSA investigation PE13-002 closure report describes Volvo Trucks North America recall 13V268 / RVXX1303 for a defined population of model-year 2007–2014 VAH, VHD, VNL, VNM and VT trucks with the specified automated transmission. In the documented circumstances, loss of a primary brake-applied signal without the redundant switch could prevent the clutch from disengaging at low speed, with a risk of extended stopping or unintended movement. Check the actual VIN and current recall status with Volvo and use the current brake-signal and transmission diagnostic plan; this history does not establish the cause of every clutch-drag complaint.

Separately, Volvo's 2018 AMT-F Tech Tool note documents a calibration routine that could stop at 33% because the historical tool attempted to calibrate a crawler section that was not installed. It identifies a tool-version correction and different procedures according to what had been replaced. Match the truck, tool version and exact error before treating an aborted calibration as evidence of a defective gearbox; consult current Volvo service information.

After TECU programming: P1061-54. Volvo’s AMT-F I-Shift/mDRIVE calibration note describes a clutch-cylinder slip-point calibration fault and transmission-check message that may appear after programming. In the documented AMT-F situation, valid existing clutch-position and shifter calibrations can be transferred by the diagnostic tool, while the slip point is handled separately. A blank replacement TECU has different requirements; older AMT-C/D procedures also differ. Record the full code and programming history and follow the current generation-specific Volvo/Mack procedure before assuming a failed clutch or controller. The note describes a specific post-programming state, not an explanation for every P1061-54 in service.

Practical evidence and service

  1. Record the exact complaint, warning text, gear, load, gradient, temperature and whether it occurs when starting, engaging drive, taking up the clutch or changing a particular gear. Preserve fault data and prior work before clearing or programming.
  2. Check air supply, electrical supply, relevant communications and clutch/gear feedback using the model's current guided test, and distinguish a driver-information message from a verified system fault. Do not bypass protection or assume that a pressure, speed or actuator fault identifies a single failed part.
  3. Where a power take-off is fitted, establish its command and engagement state. In Volvo's documented transmission-mounted PTO example, engaging drive releases and then re-engages the clutch; shifting is restricted while that PTO is active. This behaviour is configuration-specific. Volvo Trucks: I-Shift PTO FAQs.
  4. Perform programming, clutch/gear learning and sensor calibration only when the current procedure calls for them, with the specified diagnostic equipment and safety conditions. Follow the model-specific recovery and verification procedures; actuators can move and air systems can remain pressurised.

See Mack mDRIVE faults and diagnosis for related commercial-vehicle cases with their own applicability, Eaton UltraShift PLUS diagnosis for a different commercial-vehicle architecture and the electronic gearbox index.

Revision 4: Volvo Trucks I-Shift automated manual operation and diagnosis

Volvo Trucks I-Shift is a family of electronically controlled automated manual transmissions for commercial vehicles. Volvo describes the original I-Shift as based on a non-synchronised manual-type gearbox; the family later acquired other versions, including an I-Shift Dual Clutch. The single-clutch examples below are not a universal procedure for the dual-clutch model, every generation or another Volvo vehicle. Identify the truck and market, transmission model, TECU hardware and software, clutch and service history. Volvo Trucks: I-Shift generations.

System and diagnostic starting point

In the North American Volvo service example described below, the I-Shift/mDRIVE automated manual uses a push-type clutch rather than the torque converter of a conventional automatic. The controller coordinates the clutch, gearbox and engine. Pneumatic supply and electronic communications can both affect operation. Match the truck, transmission variant and software before interpreting a warning or selecting a procedure. Volvo: clutch protection message; Volvo: clutch control actuator service program.

Volvo's 2022 I-Shift diagnostic advice calls for an interview, reproducing the complaint under the relevant conditions and recording all active and inactive faults and occurrence counts. It warns against programming the transmission ECU early in the diagnosis unless directed, since useful fault information and diagnostic or calibration access can be lost. If the problem persists without codes, it points to the applicable symptom-based diagnostic plan. This is a diagnostic sequence, not a blanket instruction to clear fault memory. Volvo: do not program the TECU unless instructed.

Fault and symptom examples

Documented exampleWhat the source saysDiagnostic boundary
Clutch protection message; P1060 74 / PPID 50 FMI 11Volvo's North American service note describes a warning associated with prolonged clutch slip while the vehicle moves very little, such as holding on a gradient with the clutch slipping. In that note, the message alone is intended to discourage the operating condition; it asks for workshop investigation when associated with other clutch-control codes.Do not assume every clutch warning means worn friction material, or that the absence of another code proves a different symptom harmless. Use the exact current instructions and applicable fault context. Volvo clutch-protection note.
Clutch actuator air-loss warning on early VN/VTVolvo service program SP 413-001 describes software for specified I-Shift-equipped vehicles before 15 December 2009. Its yellow warning denotes an air leak the documented TECU strategy can compensate for, with idle driving and Eco-Roll inhibited; a larger leak can cause a red warning and buzzer with neutral selection or engine shutdown when stopped.This is a historical programme and its described software behaviour, not a diagnosis or recall applicability for all I-Shift trucks. Confirm VIN, software, warnings and current repair data. Volvo SP 413-001.
Speed-sensor related MID 130 PID 160 FMI 1/2 after parts workVolvo describes a version-C transmission example where mixing generation-C and generation-D TECU, harness/speed-sensor and sensor-wheel hardware may lead to these faults. Its service note points to a specific mixed-components bulletin.These codes can require the manufacturer fault tree and component identification; they are not proof that every sensor itself is defective or that a conversion kit fits every unit. Volvo: mixed I-Shift components.
Hill-start assist holds on level ground after TECU programming or replacementVolvo describes reset or missing inclination-sensor calibration as a possible cause on listed AMT-C, AMT-D and AMT-F trucks; its calibration sequences differ by transmission.Do not apply one generation's sequence to another or assume every unwanted brake hold is this issue. Volvo: inclination-sensor calibration.
Clutch/transmission calibration fails immediately after clutch replacement or programmingVolvo has a service note for AMT-D/F involving a missing or invalid X1 value and P1052-54 or other errors during calibration.The note's vehicle, equipment and diagnostic circumstances must be matched. The failure alone does not establish that the clutch or TECU needs replacing; use the current guided support process. Volvo: X1 and failed calibration.

Brake signal and calibration cases

The US NHTSA investigation PE13-002 closure report describes Volvo Trucks North America recall 13V268 / RVXX1303 for a defined population of model-year 2007–2014 VAH, VHD, VNL, VNM and VT trucks with the specified automated transmission. In the documented circumstances, loss of a primary brake-applied signal without the redundant switch could prevent the clutch from disengaging at low speed, with a risk of extended stopping or unintended movement. Check the actual VIN and current recall status with Volvo and use the current brake-signal and transmission diagnostic plan; this history does not establish the cause of every clutch-drag complaint.

Separately, Volvo's 2018 AMT-F Tech Tool note documents a calibration routine that could stop at 33% because the historical tool attempted to calibrate a crawler section that was not installed. It identifies a tool-version correction and different procedures according to what had been replaced. Match the truck, tool version and exact error before treating an aborted calibration as evidence of a defective gearbox; consult current Volvo service information.

After TECU programming: P1061-54. Volvo’s AMT-F I-Shift/mDRIVE calibration note describes a clutch-cylinder slip-point calibration fault and transmission-check message that may appear after programming. In the documented AMT-F situation, valid existing clutch-position and shifter calibrations can be transferred by the diagnostic tool, while the slip point is handled separately. A blank replacement TECU has different requirements; older AMT-C/D procedures also differ. Record the full code and programming history and follow the current generation-specific Volvo/Mack procedure before assuming a failed clutch or controller. The note describes a specific post-programming state, not an explanation for every P1061-54 in service.

Practical evidence and service

  1. Record the exact complaint, warning text, gear, load, gradient, temperature and whether it occurs when starting, engaging drive, taking up the clutch or changing a particular gear. Preserve fault data and prior work before clearing or programming.
  2. Check air supply, electrical supply, relevant communications and clutch/gear feedback using the model's current guided test, and distinguish a driver-information message from a verified system fault. Do not bypass protection or assume that a pressure, speed or actuator fault identifies a single failed part.
  3. Where a power take-off is fitted, establish its command and engagement state. In Volvo's documented transmission-mounted PTO example, engaging drive releases and then re-engages the clutch; shifting is restricted while that PTO is active. This behaviour is configuration-specific. Volvo Trucks: I-Shift PTO FAQs.
  4. Perform programming, clutch/gear learning and sensor calibration only when the current procedure calls for them, with the specified diagnostic equipment and safety conditions. Follow the model-specific recovery and verification procedures; actuators can move and air systems can remain pressurised.

See Mack mDRIVE faults and diagnosis for related commercial-vehicle cases with their own applicability, Eaton UltraShift PLUS diagnosis for a different commercial-vehicle architecture and the electronic gearbox index.