Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
ABS / DSC
Parent
Bluegrass Race Electronics ABS interfaces
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Bluegrass Race Electronics

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

The BRE MK60E5/E1 to Haltech CAN gateway translates signals from a separate MK60E5 or MK60E1 ABS module for Haltech engine management. It is an off-road motorsport interface, not an ABS hydraulic unit or a standalone traction controller. The engine management system must implement and configure any traction-control strategy. BRE product information.

Documented integration

BRE lists the MK60E5 and MK60E1 as compatible and specifically excludes the original non-E MK60, such as E46 systems. It says E1 lacks individual brake pressure sensors, so those pressure inputs are unavailable. The gateway provides suitable ABS data to Haltech; the maker lists wheel speeds, lateral acceleration, yaw, pressure data where available and ABS fault warning. Confirm ECU CAN settings and actual hardware with BRE. BRE compatibility and outputs.

The manufacturer’s September 2024 v1.2 manual describes integration with Haltech NSP using PD16 Box C and D identification. The product page says these identities can be changed by BRE where already in use. Do not assume compatibility with a particular Haltech model or car without confirming configuration and firmware. BRE install instructions v1.2.

Pinout

BRE gateway 8-pin connector gives the manufacturer-documented CAN1, CAN2 and power assignments.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Bluegrass MK60E5 E1 to Haltech CAN gateway

The BRE MK60E5/E1 to Haltech CAN gateway translates signals from a separate MK60E5 or MK60E1 ABS module for Haltech engine management. It is an off-road motorsport interface, not an ABS hydraulic unit or a standalone traction controller. The engine management system must implement and configure any traction-control strategy. BRE product information.

Documented integration

BRE lists the MK60E5 and MK60E1 as compatible and specifically excludes the original non-E MK60, such as E46 systems. It says E1 lacks individual brake pressure sensors, so those pressure inputs are unavailable. The gateway provides suitable ABS data to Haltech; the maker lists wheel speeds, lateral acceleration, yaw, pressure data where available and ABS fault warning. Confirm ECU CAN settings and actual hardware with BRE. BRE compatibility and outputs.

The manufacturer’s September 2024 v1.2 manual describes integration with Haltech NSP using PD16 Box C and D identification. The product page says these identities can be changed by BRE where already in use. Do not assume compatibility with a particular Haltech model or car without confirming configuration and firmware. BRE install instructions v1.2.

Pinout

BRE gateway 8-pin connector gives the manufacturer-documented CAN1, CAN2 and power assignments.

Revision 1: Bluegrass MK60E5 E1 to Haltech CAN gateway

The BRE MK60E5/E1 to Haltech CAN gateway translates signals from a separate MK60E5 or MK60E1 ABS module for Haltech engine management. It is an off-road motorsport interface, not an ABS hydraulic unit or a standalone traction controller. The engine management system must implement and configure any traction-control strategy. BRE product information.

Documented integration

BRE lists the MK60E5 and MK60E1 as compatible and specifically excludes the original non-E MK60, such as E46 systems. It says E1 lacks individual brake pressure sensors, so those pressure inputs are unavailable. The gateway provides suitable ABS data to Haltech; the maker lists wheel speeds, lateral acceleration, yaw, pressure data where available and ABS fault warning. Confirm ECU CAN settings and actual hardware with BRE. BRE compatibility and outputs.

The manufacturer’s September 2024 v1.2 manual describes integration with Haltech NSP using PD16 Box C and D identification. The product page says these identities can be changed by BRE where already in use. Do not assume compatibility with a particular Haltech model or car without confirming configuration and firmware. BRE install instructions v1.2.

Pinout

BRE gateway 8-pin connector gives the manufacturer-documented CAN1, CAN2 and power assignments.