Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
DTAFast standalone engine management
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

DTAFast E8 is a historic programmable engine-management identity documented in the manufacturer's model wiring schematic. The 14 February 1997 DTA eight-cylinder power schematic identifies four coil outputs, an injector output and fuel-pump relay wiring.

Identification

Identify the actual case label, harness connectors, output configuration and firmware. An old loom may have been modified for a particular engine. No current product availability or universal support status is inferred from this historical schematic.

Model-specific pinout and wiring

The manufacturer E8 drawing supplies connector views, functions, sensor/actuator examples and grounding. The separate E4/E6/E8 sensor schematic must be used alongside the power schematic. Both battery earth connections are called out in the period power drawing. Match connectors and diagram orientation to the actual ECU; do not transfer pin assignments from another E- or S-series model.

Power connector assignments in the 1997 drawing

The following positions are traced from the DTAFast E8 power schematic dated 14 February 1997, which labels the view as the female loom power connector. “Not shown” means the drawing does not identify a connection; it does not establish that a cavity is unused in every build. Connect both specified power grounds and use the manufacturer diagram and correct fuses and relay arrangements.

PinFunction shownAIgnition-switched supplyBBattery negative / groundCBattery negative / groundDCoil 1, earth sideECoil 2, earth sideFInjector bank 1GInjector bank 1HNot shown in this power schematicJNot shown in this power schematicKGear-change light, 20 W maximumLCoil 3, earth sideMCoil 4, earth sideNTachometer outputPFuel-pump relayRAuxiliary 2 outputSNot shown in this power schematicTNot shown in this power schematicUNot shown in this power schematic

Separate sensor connector

The DTAFast E4/E6/E8 sensor schematic dated 14 February 1997 depicts a separate male connector on the loom. The table follows the terminal connections drawn for the listed sensor examples, not the separate female power connector. “No connected function shown” is not a claim that the cavity is unused in every ECU. Use the source’s connector view and check the exact sensor and loom.

Sensor connector pinConnection in the DTAFast drawingAShift-cut switch terminal 2BShift-cut switch terminal 1CThrottle potentiometer high side (throttle open)DThrottle potentiometer wiperEThrottle potentiometer opposite endFWater-temperature sensor terminal 1GWater-temperature sensor terminal 2HAir-temperature sensor terminal 1JAir-temperature sensor terminal 2KPressure sensor terminal 3, 5 V in the Marelli exampleLPressure sensor terminal 1, signal in the Marelli exampleMCrank sensor terminal 1 in the depicted Ford/Vauxhall exampleNCrank sensor terminal 2 / shield return in the Vauxhall examplePLambda sensor terminal 2 in the diagramRLambda sensor terminal 1 / earthed sideSNo connected function shownTNo connected function shownUNo connected function shownVPressure sensor terminal 2, earth in the Marelli example

The schematic says to use screened crank-sensor cable, with the Vauxhall sensor pin 1 to M, pin 2 to N and pin 3 shield to N. It calls for reversed Ford/Marelli crank sensor polarity and states that R connects to the earthed side of the lambda sensor. Confirm sensor terminals and electrical configuration in the original diagram.

Related documentation

DTAFast's wiring archive includes crank sensor rules and legacy ECU sheets. Confirm support, software and hardware serviceability directly with DTAFast. See the DTAFast family overview.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: DTAFast E8

DTAFast E8 is a historic programmable engine-management identity documented in the manufacturer's model wiring schematic. The 14 February 1997 DTA eight-cylinder power schematic identifies four coil outputs, an injector output and fuel-pump relay wiring.

Identification

Identify the actual case label, harness connectors, output configuration and firmware. An old loom may have been modified for a particular engine. No current product availability or universal support status is inferred from this historical schematic.

Model-specific pinout and wiring

The manufacturer E8 drawing supplies connector views, functions, sensor/actuator examples and grounding. The separate E4/E6/E8 sensor schematic must be used alongside the power schematic. Both battery earth connections are called out in the period power drawing. Match connectors and diagram orientation to the actual ECU; do not transfer pin assignments from another E- or S-series model.

Power connector assignments in the 1997 drawing

The following positions are traced from the DTAFast E8 power schematic dated 14 February 1997, which labels the view as the female loom power connector. “Not shown” means the drawing does not identify a connection; it does not establish that a cavity is unused in every build. Connect both specified power grounds and use the manufacturer diagram and correct fuses and relay arrangements.

PinFunction shown
AIgnition-switched supply
BBattery negative / ground
CBattery negative / ground
DCoil 1, earth side
ECoil 2, earth side
FInjector bank 1
GInjector bank 1
HNot shown in this power schematic
JNot shown in this power schematic
KGear-change light, 20 W maximum
LCoil 3, earth side
MCoil 4, earth side
NTachometer output
PFuel-pump relay
RAuxiliary 2 output
SNot shown in this power schematic
TNot shown in this power schematic
UNot shown in this power schematic

Separate sensor connector

The DTAFast E4/E6/E8 sensor schematic dated 14 February 1997 depicts a separate male connector on the loom. The table follows the terminal connections drawn for the listed sensor examples, not the separate female power connector. “No connected function shown” is not a claim that the cavity is unused in every ECU. Use the source’s connector view and check the exact sensor and loom.

Sensor connector pinConnection in the DTAFast drawing
AShift-cut switch terminal 2
BShift-cut switch terminal 1
CThrottle potentiometer high side (throttle open)
DThrottle potentiometer wiper
EThrottle potentiometer opposite end
FWater-temperature sensor terminal 1
GWater-temperature sensor terminal 2
HAir-temperature sensor terminal 1
JAir-temperature sensor terminal 2
KPressure sensor terminal 3, 5 V in the Marelli example
LPressure sensor terminal 1, signal in the Marelli example
MCrank sensor terminal 1 in the depicted Ford/Vauxhall example
NCrank sensor terminal 2 / shield return in the Vauxhall example
PLambda sensor terminal 2 in the diagram
RLambda sensor terminal 1 / earthed side
SNo connected function shown
TNo connected function shown
UNo connected function shown
VPressure sensor terminal 2, earth in the Marelli example

The schematic says to use screened crank-sensor cable, with the Vauxhall sensor pin 1 to M, pin 2 to N and pin 3 shield to N. It calls for reversed Ford/Marelli crank sensor polarity and states that R connects to the earthed side of the lambda sensor. Confirm sensor terminals and electrical configuration in the original diagram.

Related documentation

DTAFast's wiring archive includes crank sensor rules and legacy ECU sheets. Confirm support, software and hardware serviceability directly with DTAFast. See the DTAFast family overview.

Revision 3: DTAFast E8

DTAFast E8 is a historic programmable engine-management identity documented in the manufacturer's model wiring schematic. The 14 February 1997 DTA eight-cylinder power schematic identifies four coil outputs, an injector output and fuel-pump relay wiring.

Identification

Identify the actual case label, harness connectors, output configuration and firmware. An old loom may have been modified for a particular engine. No current product availability or universal support status is inferred from this historical schematic.

Model-specific pinout and wiring

The manufacturer E8 drawing supplies connector views, functions, sensor/actuator examples and grounding. The separate E4/E6/E8 sensor schematic must be used alongside the power schematic. Both battery earth connections are called out in the period power drawing. Match connectors and diagram orientation to the actual ECU; do not transfer pin assignments from another E- or S-series model.

Power connector assignments in the 1997 drawing

The following positions are traced from the DTAFast E8 power schematic dated 14 February 1997, which labels the view as the female loom power connector. “Not shown” means the drawing does not identify a connection; it does not establish that a cavity is unused in every build. Connect both specified power grounds and use the manufacturer diagram and correct fuses and relay arrangements.

PinFunction shown
AIgnition-switched supply
BBattery negative / ground
CBattery negative / ground
DCoil 1, earth side
ECoil 2, earth side
FInjector bank 1
GInjector bank 1
HNot shown in this power schematic
JNot shown in this power schematic
KGear-change light, 20 W maximum
LCoil 3, earth side
MCoil 4, earth side
NTachometer output
PFuel-pump relay
RAuxiliary 2 output
SNot shown in this power schematic
TNot shown in this power schematic
UNot shown in this power schematic

Separate sensor connector

The DTAFast E4/E6/E8 sensor schematic dated 14 February 1997 depicts a separate male connector on the loom. The table follows the terminal connections drawn for the listed sensor examples, not the separate female power connector. “No connected function shown” is not a claim that the cavity is unused in every ECU. Use the source’s connector view and check the exact sensor and loom.

Sensor connector pinConnection in the DTAFast drawing
AShift-cut switch terminal 2
BShift-cut switch terminal 1
CThrottle potentiometer high side (throttle open)
DThrottle potentiometer wiper
EThrottle potentiometer opposite end
FWater-temperature sensor terminal 1
GWater-temperature sensor terminal 2
HAir-temperature sensor terminal 1
JAir-temperature sensor terminal 2
KPressure sensor terminal 3, 5 V in the Marelli example
LPressure sensor terminal 1, signal in the Marelli example
MCrank sensor terminal 1 in the depicted Ford/Vauxhall example
NCrank sensor terminal 2 / shield return in the Vauxhall example
PLambda sensor terminal 2 in the diagram
RLambda sensor terminal 1 / earthed side
SNo connected function shown
TNo connected function shown
UNo connected function shown
VPressure sensor terminal 2, earth in the Marelli example

The schematic says to use screened crank-sensor cable, with the Vauxhall sensor pin 1 to M, pin 2 to N and pin 3 shield to N. It calls for reversed Ford/Marelli crank sensor polarity and states that R connects to the earthed side of the lambda sensor. Confirm sensor terminals and electrical configuration in the original diagram.

Related documentation

DTAFast's wiring archive includes crank sensor rules and legacy ECU sheets. Confirm support, software and hardware serviceability directly with DTAFast. See the DTAFast family overview.