Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Link standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 4

Removed text is struck through; added text is highlighted.

Link G4+ Atom II is a documented G4+ Link engine-management designation. Link-related device documentation distinguishes the G4+ Atom II by name. Link's Atom quick-start documents four injection and four ignition drives; check revision before applying its pinout to an Atom II. Identification source.

Identification and software

Record the complete model and revision label, board identifiers, installed firmware, connector configuration and any adapter loom. Similar Link model names occur in later generations. Use the manufacturer's legacy PCLink compatibility table and seek Link support if the appropriate package is unclear.

Model-specific wiring

The identified manufacturer documentation or legacy manual archive is the starting point for this model. The table below cross-references the Link quick-start diagram and the separately identified Atom II connection guide; confirm the ECU generation and connector orientation before wiring.The identified manufacturer documentation or legacy manual archive is the starting point for this model. An individual pin-by-pin allocation was not verified in this reference; obtain the exact matching manual and connector orientation before wiring.

See Link standalone ECUs for related models and generation distinctions.

G4+ Atom shown as a family illustration; the catalogue does not identify the pictured unit as Atom II. Image: Link Engine Management G4+ catalogue, reproduced with permission.

34-position connectorLink’s G4+ Atom quick-start diagram, page 3, gives the following pin and loom colours. The AiM Link G4+ series connection guide, page 3, specifically identifies the matching layout as Atom II. The view is into the loom wire side or ECU header. Unlabelled positions are left blank in the source; this does not establish their electrical state. Verify the actual generation and connector before wiring.PinFunctionWire colourA1Inj 4Brown/orangeA2Inj 3Brown/redA3Inj 2BrownA4Inj 1Brown/blackA5+14 VRedA6Unlabelled in guide—A7Shield/groundGreenA8Trigger 1BlackA9Trigger 2RedA10Ignition 4Blue/orangeA11Ignition 3Blue/redA12Ignition 2Blue/brownA13Ignition 1BlueA14Unlabelled in guide—A15Temperature 1YellowA16Temperature 2Yellow/brownA17Analog volt 1Yellow/blueA18Auxiliary 4OrangeA19Auxiliary 3Orange/redA20Auxiliary 2Orange/brownA21Auxiliary 1Orange/blackA22Analog volt 2White/brownA23Unlabelled in guide—A24Ground outGreenA25GroundBlackA26Unlabelled in guide—A27Unlabelled in guide—A28CAN highOrange/greenA29CAN lowOrange/yellowA30DI 1Grey/blackA31DI 2Grey/brownA32+5 VRed/blueA33Analog volt 3Yellow/blackA34GroundBlackThe structured pin index and redrawn header, shared with the G4+ Atom, are in Link G4+ Atom and Atom II connector pinout.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Link G4+ Atom II

Link G4+ Atom II is a documented G4+ Link engine-management designation. Link-related device documentation distinguishes the G4+ Atom II by name. Link's Atom quick-start documents four injection and four ignition drives; check revision before applying its pinout to an Atom II. Identification source.

Identification and software

Record the complete model and revision label, board identifiers, installed firmware, connector configuration and any adapter loom. Similar Link model names occur in later generations. Use the manufacturer's legacy PCLink compatibility table and seek Link support if the appropriate package is unclear.

Model-specific wiring

The identified manufacturer documentation or legacy manual archive is the starting point for this model. An individual pin-by-pin allocation was not verified in this reference; obtain the exact matching manual and connector orientation before wiring.

See Link standalone ECUs for related models and generation distinctions.

Link G4+ atom ECU
G4+ Atom shown as a family illustration; the catalogue does not identify the pictured unit as Atom II. Image: Link Engine Management G4+ catalogue, reproduced with permission.
Revision 4: Link G4+ Atom II

Link G4+ Atom II is a documented G4+ Link engine-management designation. Link-related device documentation distinguishes the G4+ Atom II by name. Link's Atom quick-start documents four injection and four ignition drives; check revision before applying its pinout to an Atom II. Identification source.

Identification and software

Record the complete model and revision label, board identifiers, installed firmware, connector configuration and any adapter loom. Similar Link model names occur in later generations. Use the manufacturer's legacy PCLink compatibility table and seek Link support if the appropriate package is unclear.

Model-specific wiring

The identified manufacturer documentation or legacy manual archive is the starting point for this model. The table below cross-references the Link quick-start diagram and the separately identified Atom II connection guide; confirm the ECU generation and connector orientation before wiring.

See Link standalone ECUs for related models and generation distinctions.

Link G4+ atom ECU
G4+ Atom shown as a family illustration; the catalogue does not identify the pictured unit as Atom II. Image: Link Engine Management G4+ catalogue, reproduced with permission.

34-position connector

Link’s G4+ Atom quick-start diagram, page 3, gives the following pin and loom colours. The AiM Link G4+ series connection guide, page 3, specifically identifies the matching layout as Atom II. The view is into the loom wire side or ECU header. Unlabelled positions are left blank in the source; this does not establish their electrical state. Verify the actual generation and connector before wiring.

PinFunctionWire colour
A1Inj 4Brown/orange
A2Inj 3Brown/red
A3Inj 2Brown
A4Inj 1Brown/black
A5+14 VRed
A6Unlabelled in guide—
A7Shield/groundGreen
A8Trigger 1Black
A9Trigger 2Red
A10Ignition 4Blue/orange
A11Ignition 3Blue/red
A12Ignition 2Blue/brown
A13Ignition 1Blue
A14Unlabelled in guide—
A15Temperature 1Yellow
A16Temperature 2Yellow/brown
A17Analog volt 1Yellow/blue
A18Auxiliary 4Orange
A19Auxiliary 3Orange/red
A20Auxiliary 2Orange/brown
A21Auxiliary 1Orange/black
A22Analog volt 2White/brown
A23Unlabelled in guide—
A24Ground outGreen
A25GroundBlack
A26Unlabelled in guide—
A27Unlabelled in guide—
A28CAN highOrange/green
A29CAN lowOrange/yellow
A30DI 1Grey/black
A31DI 2Grey/brown
A32+5 VRed/blue
A33Analog volt 3Yellow/black
A34GroundBlack

The structured pin index and redrawn header, shared with the G4+ Atom, are in Link G4+ Atom and Atom II connector pinout.