Removed text is struck through; added text is highlighted.
Commander 950 controller and system. Image from the Holley manufacturer manual, cover; reproduced with permission.
Holley Commander 950 is a legacy programmable EFI system with throttle-body and multiport arrangements and optional ignition timing control, depending on the ignition hardware. The Commander 950 hardware and tuning manual covers system types, connector wiring and ignition examples.
Ignition scope
The manual describes electronically controlled GM HEI, Ford TFI and crank-trigger/capacitive-discharge combinations. Non-computer-controlled inductive systems can supply RPM without giving the ECU timing control. Match the physical distributor, ignition box and harness to the original diagram rather than assuming all C950 installations control spark.
Software and support
Holley's legacy resources list Commander 950 software, tuning documentation and base maps. The listed legacy software has operating-system limitations; preserve the existing calibration and verify compatibility before editing.
See the Holley EFI manufacturer index. Sources reviewed 17 November 2026.
Commander 950 ECU connector schedule
The following tables transcribe all 56 lettered and numbered ECU positions shown in figures 85–88 of the Holley Commander 950 Pro hardware and tuning manual, PDF pages 110–113. Figures 85, 86 and 87 cover GM TPI harness 271R865A, Holley SBC/BBC multiport 271R875A and Holley 4-barrel TBI 271R884A; figure 88 covers GM LT1/LT4 harness 271R886A. The figure 85 harness colours are shown where a wire is drawn. An empty colour field means no wire colour is shown in that diagram; “not used” is the source label for the illustrated build, not proof about every other harness. The diagrams describe connectors viewed from the end away from the wires. Check the precise ECU, harness and ignition arrangement against the complete schematic.
The LT1/LT4 diagram labels D8 “NOSenable” and D9 “NOS1”, whereas figures 85–87 label D8 “NOT USED” and D9 “Output 1”. The other labels below reproduce figure 85; figure 88 uses “AC Request”, “Park / Neutral” and “Cooling Fan Relay” for B8, B10 and C1 respectively. Configurable and unconnected functions depend on the specific hardware and calibration.
Open each version to inspect formatting, tables and photographs.
Revision 3: Holley Commander 950Commander 950 controller and system. Image from the Holley manufacturer manual, cover; reproduced with permission.
Holley Commander 950 is a legacy programmable EFI system with throttle-body and multiport arrangements and optional ignition timing control, depending on the ignition hardware. The Commander 950 hardware and tuning manual covers system types, connector wiring and ignition examples.
Ignition scope
The manual describes electronically controlled GM HEI, Ford TFI and crank-trigger/capacitive-discharge combinations. Non-computer-controlled inductive systems can supply RPM without giving the ECU timing control. Match the physical distributor, ignition box and harness to the original diagram rather than assuming all C950 installations control spark.
Software and support
Holley's legacy resources list Commander 950 software, tuning documentation and base maps. The listed legacy software has operating-system limitations; preserve the existing calibration and verify compatibility before editing.
The following tables transcribe all 56 lettered and numbered ECU positions shown in figures 85–88 of the Holley Commander 950 Pro hardware and tuning manual, PDF pages 110–113. Figures 85, 86 and 87 cover GM TPI harness 271R865A, Holley SBC/BBC multiport 271R875A and Holley 4-barrel TBI 271R884A; figure 88 covers GM LT1/LT4 harness 271R886A. The figure 85 harness colours are shown where a wire is drawn. An empty colour field means no wire colour is shown in that diagram; “not used” is the source label for the illustrated build, not proof about every other harness. The diagrams describe connectors viewed from the end away from the wires. Check the precise ECU, harness and ignition arrangement against the complete schematic.
The LT1/LT4 diagram labels D8 “NOSenable” and D9 “NOS1”, whereas figures 85–87 label D8 “NOT USED” and D9 “Output 1”. The other labels below reproduce figure 85; figure 88 uses “AC Request”, “Park / Neutral” and “Cooling Fan Relay” for B8, B10 and C1 respectively. Configurable and unconnected functions depend on the specific hardware and calibration.
Connector A
Pin
Figure 85 function
Figure 85 harness colour
A1
Fuel Pump Relay
Green/Black
A2
ModA
Brown
A3
ModB
Green
A4
NOT USED
A5
NOT USED
A6
Vswitch (switched power)
Red/White
A7
NOT USED
A8
RxD
Yellow
A9
TxD
Orange
A10
Vehicle Speed
A11
NOT USED
A12
SERIAL GND
Black/White
Connector B
Pin
Figure 85 function
Figure 85 harness colour
B1
Battery
Red
B2
NOT USED
B3
ECU GND
Black
B4
MAP
Red/Black
B5
Ref / PIP
Yellow/Black
B6
SlewFuel
B7
ESC (knock)
B8
AC Request / Input 1
Orange/Red
B9
IPU (+)
Purple
B10
Park-Neutral / Input 2
Dark Blue
B11
IPU (-)
Green
B12
SlewSpark
Connector C
Pin
Figure 85 function
Figure 85 harness colour
C1
Fan Relay / Output 2
C2
NOT USED
C3
IAC "B" Lo
Purple/White
C4
IAC "B" Hi
Purple/Black
C5
IAC "A" Hi
Purple/Yellow
C6
IAC "A" Lo
Purple/Blue
C7
NOT USED
C8
NOT USED
C9
Points Out
White
C10
Coolant Temp
Brown
C11
Coil (-)
Yellow
C12
MAT signal
Blue
C13
TPS signal
Green
C14
+5 Volt ref
Orange
C15
NOT USED
C16
Battery
Red
Connector D
Pin
Figure 85 function
Figure 85 harness colour
D1
ECU GND
Black
D2
Analog GND
Black/White
D3
Analog GND
Black/White
D4
EST / SPOUT
Blue/White
D5
Bypass
Tan/Black
D6
Analog GND
Black/White
D7
O2 Sensor signal
Purple
D8
NOT USED
D9
Output 1
D10
ECU GND
Black
D11
NOT USED
D12
NOT USED
D13
Injector A
White/Blue
D14
Injector B
White/Red
D15
Injector C
White/Brown
D16
Injector D
White/Green
Revision 3: Holley Commander 950Commander 950 controller and system. Image from the Holley manufacturer manual, cover; reproduced with permission.
Holley Commander 950 is a legacy programmable EFI system with throttle-body and multiport arrangements and optional ignition timing control, depending on the ignition hardware. The Commander 950 hardware and tuning manual covers system types, connector wiring and ignition examples.
Ignition scope
The manual describes electronically controlled GM HEI, Ford TFI and crank-trigger/capacitive-discharge combinations. Non-computer-controlled inductive systems can supply RPM without giving the ECU timing control. Match the physical distributor, ignition box and harness to the original diagram rather than assuming all C950 installations control spark.
Software and support
Holley's legacy resources list Commander 950 software, tuning documentation and base maps. The listed legacy software has operating-system limitations; preserve the existing calibration and verify compatibility before editing.
The following tables transcribe all 56 lettered and numbered ECU positions shown in figures 85–88 of the Holley Commander 950 Pro hardware and tuning manual, PDF pages 110–113. Figures 85, 86 and 87 cover GM TPI harness 271R865A, Holley SBC/BBC multiport 271R875A and Holley 4-barrel TBI 271R884A; figure 88 covers GM LT1/LT4 harness 271R886A. The figure 85 harness colours are shown where a wire is drawn. An empty colour field means no wire colour is shown in that diagram; “not used” is the source label for the illustrated build, not proof about every other harness. The diagrams describe connectors viewed from the end away from the wires. Check the precise ECU, harness and ignition arrangement against the complete schematic.
The LT1/LT4 diagram labels D8 “NOSenable” and D9 “NOS1”, whereas figures 85–87 label D8 “NOT USED” and D9 “Output 1”. The other labels below reproduce figure 85; figure 88 uses “AC Request”, “Park / Neutral” and “Cooling Fan Relay” for B8, B10 and C1 respectively. Configurable and unconnected functions depend on the specific hardware and calibration.