Removed text is struck through; added text is highlighted.
AEM EMS Series 2 30-6821 is an application-specific Subaru plug-in engine-management system. The manufacturer manual identifies 2005–2006 US-market Impreza WRX STI 2.5-litre turbo; 2004 is identified separately as 30-6820.
AEM 30-6052 shown as a Series 2 family illustration; connector and application differ. AEM / Holley manufacturer photograph, reproduced with permission.
Document limitations and partial pin reference
The manual cover and application summary identify both 30-6820 and 30-6821, but the full chart on pages 17–20 is explicitly headed 30-6820 even though its vehicle column combines both model years. The year-differences text refers to 30-1820/1821, while its page 16 illustration has five connectors and the chart has four. The summary conflicts with the chart for B13/B14 and several input descriptions; the conversion comparison also says Injector 5/6 moved away from A2/A3 while the chart still assigns them there. The source therefore does not establish an independently verified complete 30-6821 cavity schedule; confirm the part number, hardware, connector and each pin with AEM before wiring.
The partial entries below are from the manual’s page 16 summary, which names both models, except B27 from the page 3 year-specific fuel-pump discussion. Use the original source to resolve discrepancies and confirm configuration. The fuel-pump output must connect to the original pump control unit rather than directly to a relay. The related 30-6820 page reproduces the manufacturer’s separately labelled chart for reference; it is not proof that every assignment applies to 30-6821.
PinFunction in sourceNotes and limitationsA1Switch 3Switched +12 V inputA6Injector 7Spare injector driver, 1.5 A maxA7Injector 8Spare injector driver, 1.5 A maxA12Low side 3Spare low-side driverA13Low side 2Spare low-side driverA14Low side 4Spare low-side driverA17Low side 10Check engine lightA24Low side 11Spare low-side driverA28Injector 9VVC right camA29Injector 10VVC left camA32PW 2Boost solenoidA33ADCR 13Spare 0–5 V input in summary; chart labels I/O OutB13Coil 5Summary says Coil 5; chart says Coil 6B14Coil 6Summary says Coil 6; chart says Coil 5B27Coil 8 / FPCU2005–2006 fuel-pump control signal, manual page 3B28CAN1HAEMnet adapter manual, explicitly lists 30-6821B29CAN1LAEMnet adapter manual, explicitly lists 30-6821B34High side 1Spare high-side driverC1Injector 6Spare injector driver, 1.5 A maxC2Injector 5Spare injector driver, 1.5 A maxC9Switch 2Switch to groundC12EGT 1EGT inputC26ADCR 14Summary calls spare 0–5 V input; chart lists TGV position sensorC27ADCR 11Summary calls spare 0–5 V input; chart lists TGV position sensorD11Switch 4Switch to groundD13Switch 5Switch to groundD20EGT 2EGT inputD24EGT 3EGT inputD29EGT 4EGT input
The manual lists Switch 2/4/5 as switched to ground and Switch 3/6 as switched to +12 V. It identifies Switch 6 as D16 / D17 depending on application; determine the correct year-specific position with AEM. It states aftermarket wideband oxygen sensing is required.
Documentation
AEM 30-6820 / 30-6821 installation manual. AEM 30-3438 AEMnet adapter manual identifies CAN1H B28 and CAN1L B29 for 30-6821.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: AEM EMS Series 2 30-6821
AEM EMS Series 2 30-6821 is an application-specific Subaru plug-in engine-management system. The manufacturer manual identifies 2005–2006 US-market Impreza WRX STI 2.5-litre turbo; 2004 is identified separately as 30-6820.
AEM 30-6052 shown as a Series 2 family illustration; connector and application differ. AEM / Holley manufacturer photograph, reproduced with permission.
Document limitations and partial pin reference
The manual cover and application summary identify both 30-6820 and 30-6821, but the full chart on pages 17–20 is explicitly headed 30-6820 even though its vehicle column combines both model years. The year-differences text refers to 30-1820/1821, while its page 16 illustration has five connectors and the chart has four. The summary conflicts with the chart for B13/B14 and several input descriptions; the conversion comparison also says Injector 5/6 moved away from A2/A3 while the chart still assigns them there. The source therefore does not establish an independently verified complete 30-6821 cavity schedule; confirm the part number, hardware, connector and each pin with AEM before wiring.
The partial entries below are from the manual’s page 16 summary, which names both models, except B27 from the page 3 year-specific fuel-pump discussion. Use the original source to resolve discrepancies and confirm configuration. The fuel-pump output must connect to the original pump control unit rather than directly to a relay. The related 30-6820 page reproduces the manufacturer’s separately labelled chart for reference; it is not proof that every assignment applies to 30-6821.
Pin
Function in source
Notes and limitations
A1
Switch 3
Switched +12 V input
A6
Injector 7
Spare injector driver, 1.5 A max
A7
Injector 8
Spare injector driver, 1.5 A max
A12
Low side 3
Spare low-side driver
A13
Low side 2
Spare low-side driver
A14
Low side 4
Spare low-side driver
A17
Low side 10
Check engine light
A24
Low side 11
Spare low-side driver
A28
Injector 9
VVC right cam
A29
Injector 10
VVC left cam
A32
PW 2
Boost solenoid
A33
ADCR 13
Spare 0–5 V input in summary; chart labels I/O Out
B13
Coil 5
Summary says Coil 5; chart says Coil 6
B14
Coil 6
Summary says Coil 6; chart says Coil 5
B27
Coil 8 / FPCU
2005–2006 fuel-pump control signal, manual page 3
B28
CAN1H
AEMnet adapter manual, explicitly lists 30-6821
B29
CAN1L
AEMnet adapter manual, explicitly lists 30-6821
B34
High side 1
Spare high-side driver
C1
Injector 6
Spare injector driver, 1.5 A max
C2
Injector 5
Spare injector driver, 1.5 A max
C9
Switch 2
Switch to ground
C12
EGT 1
EGT input
C26
ADCR 14
Summary calls spare 0–5 V input; chart lists TGV position sensor
C27
ADCR 11
Summary calls spare 0–5 V input; chart lists TGV position sensor
D11
Switch 4
Switch to ground
D13
Switch 5
Switch to ground
D20
EGT 2
EGT input
D24
EGT 3
EGT input
D29
EGT 4
EGT input
The manual lists Switch 2/4/5 as switched to ground and Switch 3/6 as switched to +12 V. It identifies Switch 6 as D16 / D17 depending on application; determine the correct year-specific position with AEM. It states aftermarket wideband oxygen sensing is required.
AEM EMS Series 2 30-6821 is an application-specific Subaru plug-in engine-management system. The manufacturer manual identifies 2005–2006 US-market Impreza WRX STI 2.5-litre turbo; 2004 is identified separately as 30-6820.
AEM 30-6052 shown as a Series 2 family illustration; connector and application differ. AEM / Holley manufacturer photograph, reproduced with permission.
Document limitations and partial pin reference
The manual cover and application summary identify both 30-6820 and 30-6821, but the full chart on pages 17–20 is explicitly headed 30-6820 even though its vehicle column combines both model years. The year-differences text refers to 30-1820/1821, while its page 16 illustration has five connectors and the chart has four. The summary conflicts with the chart for B13/B14 and several input descriptions; the conversion comparison also says Injector 5/6 moved away from A2/A3 while the chart still assigns them there. The source therefore does not establish an independently verified complete 30-6821 cavity schedule; confirm the part number, hardware, connector and each pin with AEM before wiring.
The partial entries below are from the manual’s page 16 summary, which names both models, except B27 from the page 3 year-specific fuel-pump discussion. Use the original source to resolve discrepancies and confirm configuration. The fuel-pump output must connect to the original pump control unit rather than directly to a relay. The related 30-6820 page reproduces the manufacturer’s separately labelled chart for reference; it is not proof that every assignment applies to 30-6821.
Pin
Function in source
Notes and limitations
A1
Switch 3
Switched +12 V input
A6
Injector 7
Spare injector driver, 1.5 A max
A7
Injector 8
Spare injector driver, 1.5 A max
A12
Low side 3
Spare low-side driver
A13
Low side 2
Spare low-side driver
A14
Low side 4
Spare low-side driver
A17
Low side 10
Check engine light
A24
Low side 11
Spare low-side driver
A28
Injector 9
VVC right cam
A29
Injector 10
VVC left cam
A32
PW 2
Boost solenoid
A33
ADCR 13
Spare 0–5 V input in summary; chart labels I/O Out
B13
Coil 5
Summary says Coil 5; chart says Coil 6
B14
Coil 6
Summary says Coil 6; chart says Coil 5
B27
Coil 8 / FPCU
2005–2006 fuel-pump control signal, manual page 3
B28
CAN1H
AEMnet adapter manual, explicitly lists 30-6821
B29
CAN1L
AEMnet adapter manual, explicitly lists 30-6821
B34
High side 1
Spare high-side driver
C1
Injector 6
Spare injector driver, 1.5 A max
C2
Injector 5
Spare injector driver, 1.5 A max
C9
Switch 2
Switch to ground
C12
EGT 1
EGT input
C26
ADCR 14
Summary calls spare 0–5 V input; chart lists TGV position sensor
C27
ADCR 11
Summary calls spare 0–5 V input; chart lists TGV position sensor
D11
Switch 4
Switch to ground
D13
Switch 5
Switch to ground
D20
EGT 2
EGT input
D24
EGT 3
EGT input
D29
EGT 4
EGT input
The manual lists Switch 2/4/5 as switched to ground and Switch 3/6 as switched to +12 V. It identifies Switch 6 as D16 / D17 depending on application; determine the correct year-specific position with AEM. It states aftermarket wideband oxygen sensing is required.