Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
AEM EMS Series 2
Applies to
AEM EMS Series 2
Tool groups
None
Manufacturers
None

AEM EMS Series 2 30-6821 is an application-specific Subaru plug-in engine-management system. The manufacturer manual identifies 2005–2006 US-market Impreza WRX STI 2.5-litre turbo; 2004 is identified separately as 30-6820.

AEM Series 2 30-6052 ECU
AEM 30-6052 shown as a Series 2 family illustration; connector and application differ. AEM / Holley manufacturer photograph, reproduced with permission.

Document limitations and partial pin reference

The manual cover and application summary identify both 30-6820 and 30-6821, but the full chart on pages 17–20 is explicitly headed 30-6820 even though its vehicle column combines both model years. The year-differences text refers to 30-1820/1821, while its page 16 illustration has five connectors and the chart has four. The summary conflicts with the chart for B13/B14 and several input descriptions; the conversion comparison also says Injector 5/6 moved away from A2/A3 while the chart still assigns them there. The source therefore does not establish an independently verified complete 30-6821 cavity schedule; confirm the part number, hardware, connector and each pin with AEM before wiring.

The partial entries below are from the manual’s page 16 summary, which names both models, except B27 from the page 3 year-specific fuel-pump discussion. Use the original source to resolve discrepancies and confirm configuration. The fuel-pump output must connect to the original pump control unit rather than directly to a relay. The related 30-6820 page reproduces the manufacturer’s separately labelled chart for reference; it is not proof that every assignment applies to 30-6821.

PinFunction in sourceNotes and limitations
A1Switch 3Switched +12 V input
A6Injector 7Spare injector driver, 1.5 A max
A7Injector 8Spare injector driver, 1.5 A max
A12Low side 3Spare low-side driver
A13Low side 2Spare low-side driver
A14Low side 4Spare low-side driver
A17Low side 10Check engine light
A24Low side 11Spare low-side driver
A28Injector 9VVC right cam
A29Injector 10VVC left cam
A32PW 2Boost solenoid
A33ADCR 13Spare 0–5 V input in summary; chart labels I/O Out
B13Coil 5Summary says Coil 5; chart says Coil 6
B14Coil 6Summary says Coil 6; chart says Coil 5
B27Coil 8 / FPCU2005–2006 fuel-pump control signal, manual page 3
B28CAN1HAEMnet adapter manual, explicitly lists 30-6821
B29CAN1LAEMnet adapter manual, explicitly lists 30-6821
B34High side 1Spare high-side driver
C1Injector 6Spare injector driver, 1.5 A max
C2Injector 5Spare injector driver, 1.5 A max
C9Switch 2Switch to ground
C12EGT 1EGT input
C26ADCR 14Summary calls spare 0–5 V input; chart lists TGV position sensor
C27ADCR 11Summary calls spare 0–5 V input; chart lists TGV position sensor
D11Switch 4Switch to ground
D13Switch 5Switch to ground
D20EGT 2EGT input
D24EGT 3EGT input
D29EGT 4EGT input

The manual lists Switch 2/4/5 as switched to ground and Switch 3/6 as switched to +12 V. It identifies Switch 6 as D16 / D17 depending on application; determine the correct year-specific position with AEM. It states aftermarket wideband oxygen sensing is required.

Documentation

AEM 30-6820 / 30-6821 installation manual. AEM 30-3438 AEMnet adapter manual identifies CAN1H B28 and CAN1L B29 for 30-6821.