Removed text is struck through; added text is highlighted.
Adaptronic eSel043 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Suzuki Swift GTi Mk I G13B DOHC and Mk II G13B 16-valve DOHC applications listed by Adaptronic. Adaptronic eSel043 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel043 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel043 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Adaptronic manufacturer index
Manufacturer connector table
From the Adaptronic eSel043 installation guide, pages 20–21. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide.
Adaptronic eSel040 shown as a Select-family illustration; eSel043 applications, labels and connectors differ. Photo from the eSel040 manufacturer guide, page 1; reproduced with permission.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 4: Adaptronic eSel043
Adaptronic eSel043 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Suzuki Swift GTi Mk I G13B DOHC and Mk II G13B 16-valve DOHC applications listed by Adaptronic. Adaptronic eSel043 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel043 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel043 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
From the Adaptronic eSel043 installation guide, pages 20–21. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide.
Factory pin
Wire colour
Factory ECU function
Adaptronic connector pin
Adaptronic function
Notes
A1
Wht
+12V Ignition
1A
+12IG
—
A13
Blk/Grn
Ground
1B
PGND
—
A2
Wht
+12V Ignition
1C
+12IG
—
A14
Blk/Grn
Ground
1D
PGND
—
A3
Wht
MAF Power
1E
ExtIn
—
A15
—
—
1F
Knock
—
A4
Red
TPS +5V
1G
TPS5V
—
A16
—
Constant 12V
1H
CONSTIN
—
A5
Lt Grn/Blk
Sensor Ground
1I
GND
—
A17
—
—
1J
Aux Output 8
Shift Light
A6
Blk/Grn
MAF Signal
1K
MAP
—
A18
Blu/Red
AC Compressor
1L
Aux 7
Aircon
A7
Blu/Wht
WT signal
1M
ECT
—
A19
Vio/Grn
Diagnostic
1N
CAS 3
Flex
A8
—
Oxygen sensor
1O
O2
—
A20
—
—
1P
SVSS2
—
A9
Grn
TPS Sig
1Q
TPS
—
A21
Wht
TPS Switch
1R
Dig In 2
Neutral Switch
A10
Yel/Grn
VSS
1S
MVSS1
—
A22
Vio/Yel
Diagnostic
1T
MAT
—
A11
—
—
1U
MVSS2
—
A23
Brn/Blk
EGR Sensor
1V
AuxT
—
A12
Brn/Blk
Ign Coil
1W
—
—
A24
—
—
1X
SVSS1
—
B1
Red
Reluctor pos
2A
CAS 1
—
B10
Grn
Reluctor neg
2B
GND
—
B2
Vio
Check Light
2C
Aux Output 6
MIL
B11
Brn/Yel
Elec Load
2D
Dig In 1
Electrical Load
B3
Blu/Yel
Steer valve
2E
Aux Output 3
Boost Control
B12
Blu/Wht
Psteer Sw
2F
Dig In 3
Spare
B4
—
—
2G
Ign 4
—
B13
Pnk/Wht
Fuel Pump
2H
Aux Output 5
Fuel Pump
B5
Red/Grn
Purge Valve
2I
Aux Output 4
Purge valve
B14
Red/Yel
EGR
2J
Aux Output 1
EGR
B6
—
—
2K
Inj 4
—
B15
—
—
2L
Ign 3
—
B7
Vio/Red
Diagnostic
2M
CAS 2
—
B16
Blk/Grn
Ground
2N
PGND
—
B8
Wht/Blk
Main Relay
2O
PGND
—
B17
—
—
2P
Ign 2
—
B9
—
—
2Q
Inj 2
—
B18
Red/Wht
Idle-Up
2R
Aux Output 2
Idle Control
C1
Blk/Yel
Crank
3A
Dig In 7
Mileage
C6
Brn/Yel
Ign Drive
3B
Ign 1
—
C2
Wht/Blk
+12V Ign
3C
+12Inj
—
C7
Wht/Blk
+12V Ign
3D
+12Inj
—
C3
Yel/Red
Inj 2A
3E
Inj 3
—
C8
Blu
Inj Power
3F
+12Inj
—
C4
Yel/Wht
Inj 3A
3G
Inj 1
—
C9
Blu
Inj Power
3H
+12Inj
—
C5
Blk/Blu
GND
3I
PGND
—
C10
Blk/Blu
GND
3J
PGND
—
Select family illustration
Adaptronic eSel040 shown as a Select-family illustration; eSel043 applications, labels and connectors differ. Photo from the eSel040 manufacturer guide, page 1; reproduced with permission.Revision 4: Adaptronic eSel043
Adaptronic eSel043 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Suzuki Swift GTi Mk I G13B DOHC and Mk II G13B 16-valve DOHC applications listed by Adaptronic. Adaptronic eSel043 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel043 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel043 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
From the Adaptronic eSel043 installation guide, pages 20–21. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide.
Factory pin
Wire colour
Factory ECU function
Adaptronic connector pin
Adaptronic function
Notes
A1
Wht
+12V Ignition
1A
+12IG
—
A13
Blk/Grn
Ground
1B
PGND
—
A2
Wht
+12V Ignition
1C
+12IG
—
A14
Blk/Grn
Ground
1D
PGND
—
A3
Wht
MAF Power
1E
ExtIn
—
A15
—
—
1F
Knock
—
A4
Red
TPS +5V
1G
TPS5V
—
A16
—
Constant 12V
1H
CONSTIN
—
A5
Lt Grn/Blk
Sensor Ground
1I
GND
—
A17
—
—
1J
Aux Output 8
Shift Light
A6
Blk/Grn
MAF Signal
1K
MAP
—
A18
Blu/Red
AC Compressor
1L
Aux 7
Aircon
A7
Blu/Wht
WT signal
1M
ECT
—
A19
Vio/Grn
Diagnostic
1N
CAS 3
Flex
A8
—
Oxygen sensor
1O
O2
—
A20
—
—
1P
SVSS2
—
A9
Grn
TPS Sig
1Q
TPS
—
A21
Wht
TPS Switch
1R
Dig In 2
Neutral Switch
A10
Yel/Grn
VSS
1S
MVSS1
—
A22
Vio/Yel
Diagnostic
1T
MAT
—
A11
—
—
1U
MVSS2
—
A23
Brn/Blk
EGR Sensor
1V
AuxT
—
A12
Brn/Blk
Ign Coil
1W
—
—
A24
—
—
1X
SVSS1
—
B1
Red
Reluctor pos
2A
CAS 1
—
B10
Grn
Reluctor neg
2B
GND
—
B2
Vio
Check Light
2C
Aux Output 6
MIL
B11
Brn/Yel
Elec Load
2D
Dig In 1
Electrical Load
B3
Blu/Yel
Steer valve
2E
Aux Output 3
Boost Control
B12
Blu/Wht
Psteer Sw
2F
Dig In 3
Spare
B4
—
—
2G
Ign 4
—
B13
Pnk/Wht
Fuel Pump
2H
Aux Output 5
Fuel Pump
B5
Red/Grn
Purge Valve
2I
Aux Output 4
Purge valve
B14
Red/Yel
EGR
2J
Aux Output 1
EGR
B6
—
—
2K
Inj 4
—
B15
—
—
2L
Ign 3
—
B7
Vio/Red
Diagnostic
2M
CAS 2
—
B16
Blk/Grn
Ground
2N
PGND
—
B8
Wht/Blk
Main Relay
2O
PGND
—
B17
—
—
2P
Ign 2
—
B9
—
—
2Q
Inj 2
—
B18
Red/Wht
Idle-Up
2R
Aux Output 2
Idle Control
C1
Blk/Yel
Crank
3A
Dig In 7
Mileage
C6
Brn/Yel
Ign Drive
3B
Ign 1
—
C2
Wht/Blk
+12V Ign
3C
+12Inj
—
C7
Wht/Blk
+12V Ign
3D
+12Inj
—
C3
Yel/Red
Inj 2A
3E
Inj 3
—
C8
Blu
Inj Power
3F
+12Inj
—
C4
Yel/Wht
Inj 3A
3G
Inj 1
—
C9
Blu
Inj Power
3H
+12Inj
—
C5
Blk/Blu
GND
3I
PGND
—
C10
Blk/Blu
GND
3J
PGND
—
Select family illustration
Adaptronic eSel040 shown as a Select-family illustration; eSel043 applications, labels and connectors differ. Photo from the eSel040 manufacturer guide, page 1; reproduced with permission.