Adaptronic eSel042 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-7 FC Series 4 (1985–1988) 13B single turbo. Adaptronic eSel042 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel042 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel042 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The assignments below are transcribed from that guide; verify the exact drawing and connector viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Manufacturer connector table
Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source repeats “left front” for both 1D and 1B in its wheel-speed comments; verify the intended position. Its direct-fire text repeats 1V in one sentence, while the coil list identifies 1V, 1X, 1U and 2O.
| Factory pin | Factory function | Adaptronic function | Installation notes |
|---|---|---|---|
| 3J | Wht / Blu Constant Power | Constant power in | — |
| 3I | Grn / Yel Ignition Power | +12V in | — |
| 3H | LtGrn / Wht Secondary Injector 1 | Injector Output 2 | — |
| 3G | Blk GND | Power Ground | — |
| 3F | LtGrn / Red Secondary Injector 2 | Injector Output 4 | — |
| 3E | LtGrn Primary Injector 1 | Injector Output 1 | — |
| 3D | Blk / Red Starter inhibit | Aux Output 5 | Fuel-pump modification needed if airflow meter is removed; see guide. |
| 3C | LtGrn / Blk Primary Injector 2 | Injector Output 3 | — |
| 3B | Blk / Blu Starter input | — | — |
| 3A | Blk GND | Power Ground | — |
| 2R | Blk GND | Power Ground | — |
| 2Q | Blu / Grn Idle Control | Aux Output 2 | — |
| 2P | Blu / Yel Relief Valve | Digital Input 6 | Factory output; available as ECU digital input. |
| 2O | Blu / Red Switching Valve | Ignition Output 4 | Factory output; optional second-rotor leading ignition for four-coil conversion. |
| 2N | Blu / Wht EGR Valve | — | — |
| 2M | Blu / Ora Pressure reg control valve | Aux Output 4 | Temporarily isolates regulator vacuum after starting. |
| 2L | Grn Manifold Air Temp | Air Temp Input (MAT) | — |
| 2K | Blu / Blk Turbo Control Valve | Aux Output 3 | Boost control. |
| 2J | Grn / Ora Inlet Air Temp | Aux Temp Input | — |
| 2I | Grn / Wht Engine Coolant Temp | Coolant Temp Input | — |
| 2H | Grn / Yel ATP | — | — |
| 2G | Grn / Red TPS Signal | TPS Input | — |
| 2F | Grn / Blk Variable Resistor (tuning) | MVSS Input | Optional vehicle-speed input; factory ECU has none. |
| 2E | Grn / Blu Airflow Signal | Ext 0-5V Input | Available 0–5 V input; not used for tuning. |
| 2D | Grey Oxygen Sensor Signal | O2 Input | — |
| 2C | Blk Sensor Ground | Sensor GND | — |
| 2B | Brn / Red MAP Signal | MAP Input | Optional internal MAP sensor. |
| 2A | Brn / Wht 5V Sensor Supply | TPS +5V | — |
| 1X | Blu / Yel Ignition Trailing | Ignition Output 2 | 180° firing interval. |
| 1W | Blk / Yel Heat Hazard | Aux Output 6 | Dashboard indicator. |
| 1V | Grn / Yel Ignition Leading | Ignition Output 1 | 180° firing interval. |
| 1U | Brn / Yel Ignition Select | Ignition Output 3 | Coil selection. |
| 1T | Red CAS: 24-tooth trigger | CAS 2 | Other RX-7 plug-ins use CAS1 for multi-tooth trigger. |
| 1S | Brn / Red Port Air Valve | Aux Output 1 | Port air injection. |
| 1R | LtGrn Knock Input | Digital Input 5 | Knock-module input. |
| 1Q | Wht CAS Ground | Sensor GND | — |
| 1P | Blu CAS Ground | Sensor GND | — |
| 1O | Blu / Blk Mileage sensor | Digital Input 7 | Available digital input. |
| 1N | Grn CAS: 2-tooth trigger | CAS 1 | Other RX-7 plug-ins use CAS2 for reset trigger. |
| 1M | Blu / Red Ignition Feedback | — | — |
| 1L | Yel / Blu Clutch Switch | Digital Input 1 | — |
| 1K | Blk / Red Shift Light | Aux Output 8 | — |
| 1J | Ora Check Connector | MVSS 2 | Four-wheel setup: right rear speed. |
| 1I | Blk / Blu "Overtop" (overdrive) | Digital Input 3 | — |
| 1H | Brn Water Temp Switch | Knock | May accept a direct knock sensor. |
| 1G | Grn / Blk Neutral Switch | Digital Input 2 | — |
| 1F | Blu / Wht Air Conditioner Clutch | Aux Output 7 | — |
| 1E | Blu / Ora Air Conditioner Request | Digital Input 4 | — |
| 1D | Yel Check Connector | SVSS1 | Four-wheel setup: left front speed, per source. |
| 1C | Brn / Yel Air Bypass | — | — |
| 1B | Yel / Red Check Connector | SVSS2 | Four-wheel setup: left front speed, per source; duplicate with 1D. |
| 1A | Yel / Blk Check Connector | CAS3 | Optional flex-fuel input. |
Select family illustration
