Removed text is struck through; added text is highlighted.
Adaptronic eSel030 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Toyota SW20 MR2 (1989–1991) with distributor-type 3S-GTE. Adaptronic eSel030 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel030 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel030 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Adaptronic manufacturer index
Manufacturer connector table
From the Adaptronic eSel030 installation guide, pages 20–21. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide.
Factory pin labelAdaptronic connector pinFactory functionFactory colourAdaptronic functionCommentsBATT1ABatteryWhite/Red——+B11BEFI main relayBlack/Yellow——ELS1CHeadlight/defoggerBlackDig in 3 (electrical load)—+B1DEFI main relayBlack/Yellow+12V ignition—none/EGW1ENC/Exhaust temperatureRed——PSCT1FPower steering ECUBlue/YellowAux 8 (ground when RPM<500)—STP1GStop light switchGreen/WhiteDig in 5 (electrical load)—PS1HPower steering ECUBlackDig in 4 (electrical load)—W1ICheck Engine LightGreen/WhiteAux 6—none/CCO1JCheck connectorPink——FPR1KFuel pump relayBlue/RedAux 7—-1LNC———-1MNC—SVSS1—-1NNC—SVSS2—ABS1OABS ECUGreen/YellowAux 8 (ground when RPM<500)—-1PNC———SPD1QSpeed sensorPurple/WhiteMVSS1—-1RNC—MVSS2—AC11SA/C magnet switchBlack/WhiteDig in 2 (AC Request, act high)—-1TNC———STA1UStarter switchRed——-1VNC———VC3ASensor power sourceRed/BlueMAP +5V or TPS +5V—E23BSensor GroundBrownMAP GND or TPS GNDSGNDVS3CAFMYellow/BlueExtIn—THG3DEGR gas temp sensorBlack/Yellow (X)AuxTemp—THA 13EAir temp (inside AFM)BlackMAT—VTA3FTPSWhiteTPS sig—THW3GWater temp sensorRedECT—IDL3HTPSPinkDig in 1 (closed throttle)—KNK3IKnock sensorBlackKnock—PIM3JTurbo pressure sensorBlue/BlackMAP sig—OX13KMain oxygen sensorBlackEGOO2OX23LSub oxygen sensorBlack——-3MNC—Dig in 6—T3NCheck connectorOrangeDig in 7—VF3OCheck connectorRed/WhiteDig in 8—G-3PDistributorRedCAS groundSGNDNE4ADistributorBlackTrig 1CAS1E14BEngine GroundBrownPGND—G24CDistributorGreenTrig 2CAS2G14DDistributorWhiteTrig 3CAS3IGF4EIgniter (feedback)White/Red——-4FNC———-4GNC———FC4HCircuit opening relayGreen/RedAux 5—-4INC———TVIS4JT-VIS VSVGreen/BlackAux 1—TPC14KTurbo pressure VSVBlue/OrangeAux 2 (boost control)—-4LNC—Ign2—-4MNC—Ign3—IGT4NIgniterWhiteIgn1—HT4OOxygen sensor heaterRed/White (X)PGND—-4PNC—Ign4—RSC4QISC valveRedAux 4—RSO4RISC valveGreenAux 3—STJ4SCold start injectorGreen (X)——EGR4TEGR valveRed (X)——No.24UInjector 2White/BlueInj4—No.44VInjector 4Green/YellowInj3—No.14WInjector 1Red/WhiteInj1—No.34XInjector 3Black/WhiteInj2—E014YPower GroundBrownPGND—E024ZPower GroundBrownPGND—
Select family illustration
Adaptronic eSel040 shown as a Select-family illustration; eSel030 applications, labels and connectors differ. Photo from the eSel040 manufacturer guide, page 1; reproduced with permission.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 4: Adaptronic eSel030
Adaptronic eSel030 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Toyota SW20 MR2 (1989–1991) with distributor-type 3S-GTE. Adaptronic eSel030 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel030 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel030 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
From the Adaptronic eSel030 installation guide, pages 20–21. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide.
Factory pin label
Adaptronic connector pin
Factory function
Factory colour
Adaptronic function
Comments
BATT
1A
Battery
White/Red
—
—
+B1
1B
EFI main relay
Black/Yellow
—
—
ELS
1C
Headlight/defogger
Black
Dig in 3 (electrical load)
—
+B
1D
EFI main relay
Black/Yellow
+12V ignition
—
none/EGW
1E
NC/Exhaust temperature
Red
—
—
PSCT
1F
Power steering ECU
Blue/Yellow
Aux 8 (ground when RPM<500)
—
STP
1G
Stop light switch
Green/White
Dig in 5 (electrical load)
—
PS
1H
Power steering ECU
Black
Dig in 4 (electrical load)
—
W
1I
Check Engine Light
Green/White
Aux 6
—
none/CCO
1J
Check connector
Pink
—
—
FPR
1K
Fuel pump relay
Blue/Red
Aux 7
—
-
1L
NC
—
—
—
-
1M
NC
—
SVSS1
—
-
1N
NC
—
SVSS2
—
ABS
1O
ABS ECU
Green/Yellow
Aux 8 (ground when RPM<500)
—
-
1P
NC
—
—
—
SPD
1Q
Speed sensor
Purple/White
MVSS1
—
-
1R
NC
—
MVSS2
—
AC1
1S
A/C magnet switch
Black/White
Dig in 2 (AC Request, act high)
—
-
1T
NC
—
—
—
STA
1U
Starter switch
Red
—
—
-
1V
NC
—
—
—
VC
3A
Sensor power source
Red/Blue
MAP +5V or TPS +5V
—
E2
3B
Sensor Ground
Brown
MAP GND or TPS GND
SGND
VS
3C
AFM
Yellow/Blue
ExtIn
—
THG
3D
EGR gas temp sensor
Black/Yellow (X)
AuxTemp
—
THA 1
3E
Air temp (inside AFM)
Black
MAT
—
VTA
3F
TPS
White
TPS sig
—
THW
3G
Water temp sensor
Red
ECT
—
IDL
3H
TPS
Pink
Dig in 1 (closed throttle)
—
KNK
3I
Knock sensor
Black
Knock
—
PIM
3J
Turbo pressure sensor
Blue/Black
MAP sig
—
OX1
3K
Main oxygen sensor
Black
EGO
O2
OX2
3L
Sub oxygen sensor
Black
—
—
-
3M
NC
—
Dig in 6
—
T
3N
Check connector
Orange
Dig in 7
—
VF
3O
Check connector
Red/White
Dig in 8
—
G-
3P
Distributor
Red
CAS ground
SGND
NE
4A
Distributor
Black
Trig 1
CAS1
E1
4B
Engine Ground
Brown
PGND
—
G2
4C
Distributor
Green
Trig 2
CAS2
G1
4D
Distributor
White
Trig 3
CAS3
IGF
4E
Igniter (feedback)
White/Red
—
—
-
4F
NC
—
—
—
-
4G
NC
—
—
—
FC
4H
Circuit opening relay
Green/Red
Aux 5
—
-
4I
NC
—
—
—
TVIS
4J
T-VIS VSV
Green/Black
Aux 1
—
TPC1
4K
Turbo pressure VSV
Blue/Orange
Aux 2 (boost control)
—
-
4L
NC
—
Ign2
—
-
4M
NC
—
Ign3
—
IGT
4N
Igniter
White
Ign1
—
HT
4O
Oxygen sensor heater
Red/White (X)
PGND
—
-
4P
NC
—
Ign4
—
RSC
4Q
ISC valve
Red
Aux 4
—
RSO
4R
ISC valve
Green
Aux 3
—
STJ
4S
Cold start injector
Green (X)
—
—
EGR
4T
EGR valve
Red (X)
—
—
No.2
4U
Injector 2
White/Blue
Inj4
—
No.4
4V
Injector 4
Green/Yellow
Inj3
—
No.1
4W
Injector 1
Red/White
Inj1
—
No.3
4X
Injector 3
Black/White
Inj2
—
E01
4Y
Power Ground
Brown
PGND
—
E02
4Z
Power Ground
Brown
PGND
—
Select family illustration
Adaptronic eSel040 shown as a Select-family illustration; eSel030 applications, labels and connectors differ. Photo from the eSel040 manufacturer guide, page 1; reproduced with permission.Revision 4: Adaptronic eSel030
Adaptronic eSel030 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Toyota SW20 MR2 (1989–1991) with distributor-type 3S-GTE. Adaptronic eSel030 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel030 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel030 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
From the Adaptronic eSel030 installation guide, pages 20–21. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide.
Factory pin label
Adaptronic connector pin
Factory function
Factory colour
Adaptronic function
Comments
BATT
1A
Battery
White/Red
—
—
+B1
1B
EFI main relay
Black/Yellow
—
—
ELS
1C
Headlight/defogger
Black
Dig in 3 (electrical load)
—
+B
1D
EFI main relay
Black/Yellow
+12V ignition
—
none/EGW
1E
NC/Exhaust temperature
Red
—
—
PSCT
1F
Power steering ECU
Blue/Yellow
Aux 8 (ground when RPM<500)
—
STP
1G
Stop light switch
Green/White
Dig in 5 (electrical load)
—
PS
1H
Power steering ECU
Black
Dig in 4 (electrical load)
—
W
1I
Check Engine Light
Green/White
Aux 6
—
none/CCO
1J
Check connector
Pink
—
—
FPR
1K
Fuel pump relay
Blue/Red
Aux 7
—
-
1L
NC
—
—
—
-
1M
NC
—
SVSS1
—
-
1N
NC
—
SVSS2
—
ABS
1O
ABS ECU
Green/Yellow
Aux 8 (ground when RPM<500)
—
-
1P
NC
—
—
—
SPD
1Q
Speed sensor
Purple/White
MVSS1
—
-
1R
NC
—
MVSS2
—
AC1
1S
A/C magnet switch
Black/White
Dig in 2 (AC Request, act high)
—
-
1T
NC
—
—
—
STA
1U
Starter switch
Red
—
—
-
1V
NC
—
—
—
VC
3A
Sensor power source
Red/Blue
MAP +5V or TPS +5V
—
E2
3B
Sensor Ground
Brown
MAP GND or TPS GND
SGND
VS
3C
AFM
Yellow/Blue
ExtIn
—
THG
3D
EGR gas temp sensor
Black/Yellow (X)
AuxTemp
—
THA 1
3E
Air temp (inside AFM)
Black
MAT
—
VTA
3F
TPS
White
TPS sig
—
THW
3G
Water temp sensor
Red
ECT
—
IDL
3H
TPS
Pink
Dig in 1 (closed throttle)
—
KNK
3I
Knock sensor
Black
Knock
—
PIM
3J
Turbo pressure sensor
Blue/Black
MAP sig
—
OX1
3K
Main oxygen sensor
Black
EGO
O2
OX2
3L
Sub oxygen sensor
Black
—
—
-
3M
NC
—
Dig in 6
—
T
3N
Check connector
Orange
Dig in 7
—
VF
3O
Check connector
Red/White
Dig in 8
—
G-
3P
Distributor
Red
CAS ground
SGND
NE
4A
Distributor
Black
Trig 1
CAS1
E1
4B
Engine Ground
Brown
PGND
—
G2
4C
Distributor
Green
Trig 2
CAS2
G1
4D
Distributor
White
Trig 3
CAS3
IGF
4E
Igniter (feedback)
White/Red
—
—
-
4F
NC
—
—
—
-
4G
NC
—
—
—
FC
4H
Circuit opening relay
Green/Red
Aux 5
—
-
4I
NC
—
—
—
TVIS
4J
T-VIS VSV
Green/Black
Aux 1
—
TPC1
4K
Turbo pressure VSV
Blue/Orange
Aux 2 (boost control)
—
-
4L
NC
—
Ign2
—
-
4M
NC
—
Ign3
—
IGT
4N
Igniter
White
Ign1
—
HT
4O
Oxygen sensor heater
Red/White (X)
PGND
—
-
4P
NC
—
Ign4
—
RSC
4Q
ISC valve
Red
Aux 4
—
RSO
4R
ISC valve
Green
Aux 3
—
STJ
4S
Cold start injector
Green (X)
—
—
EGR
4T
EGR valve
Red (X)
—
—
No.2
4U
Injector 2
White/Blue
Inj4
—
No.4
4V
Injector 4
Green/Yellow
Inj3
—
No.1
4W
Injector 1
Red/White
Inj1
—
No.3
4X
Injector 3
Black/White
Inj2
—
E01
4Y
Power Ground
Brown
PGND
—
E02
4Z
Power Ground
Brown
PGND
—
Select family illustration
Adaptronic eSel040 shown as a Select-family illustration; eSel030 applications, labels and connectors differ. Photo from the eSel040 manufacturer guide, page 1; reproduced with permission.