Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
ABS / DSC
Parent
Bosch Motorsport ABS M4
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Bosch

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

These selected 38-position ABS M4 ECU assignments are transcribed from Bosch Motorsport’s standard ABS M4 wiring diagram F.02U.S00.043-09 in the linked manual, printed page 50. This is a diagram-specific reference, not a universal claim for all M4 vehicle-specific harnesses or road ABS units. Other positions are not specified here. WS and WP and their black/white wire descriptions are retained as printed; do not infer sensor polarity from the names alone. Check the original drawing for connector orientation, wiring options and electrical protection.

ECU pinFunction in the cited diagram1VBat motor relay; S1 fuse 40 A2Switch 13A_GND for pressure sensor4ABS warning lamp5VB switch6WS front right, black13Motor ground14CAN low15V_Stab +5 V17Diagnostic K-line18WP front right, white19WP rear right, white20WS rear left, black21WP front left, white22WS front left, black25VBat valve relay; S2 fuse 25 A26CAN high27Switch 230Brake-light switch input (+BLS)31WS rear right, black32KL15 switched supply; S3 fuse 10 A33WP rear left, white35Brake-pressure sensor signal38Valve ground

Source: Bosch Motorsport ABS M4 manual, section 16 and page 50. The wheel-speed interface and sensor adapters vary with the kit. The similar M5 connector is not a compatible harness: consult the respective Bosch instructions before wiring.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Bosch Motorsport ABS M4 ECU connector pinout

These selected 38-position ABS M4 ECU assignments are transcribed from Bosch Motorsport’s standard ABS M4 wiring diagram F.02U.S00.043-09 in the linked manual, printed page 50. This is a diagram-specific reference, not a universal claim for all M4 vehicle-specific harnesses or road ABS units. Other positions are not specified here. WS and WP and their black/white wire descriptions are retained as printed; do not infer sensor polarity from the names alone. Check the original drawing for connector orientation, wiring options and electrical protection.

ECU pinFunction in the cited diagram
1VBat motor relay; S1 fuse 40 A
2Switch 1
3A_GND for pressure sensor
4ABS warning lamp
5VB switch
6WS front right, black
13Motor ground
14CAN low
15V_Stab +5 V
17Diagnostic K-line
18WP front right, white
19WP rear right, white
20WS rear left, black
21WP front left, white
22WS front left, black
25VBat valve relay; S2 fuse 25 A
26CAN high
27Switch 2
30Brake-light switch input (+BLS)
31WS rear right, black
32KL15 switched supply; S3 fuse 10 A
33WP rear left, white
35Brake-pressure sensor signal
38Valve ground

Source: Bosch Motorsport ABS M4 manual, section 16 and page 50. The wheel-speed interface and sensor adapters vary with the kit. The similar M5 connector is not a compatible harness: consult the respective Bosch instructions before wiring.

Revision 1: Bosch Motorsport ABS M4 ECU connector pinout

These selected 38-position ABS M4 ECU assignments are transcribed from Bosch Motorsport’s standard ABS M4 wiring diagram F.02U.S00.043-09 in the linked manual, printed page 50. This is a diagram-specific reference, not a universal claim for all M4 vehicle-specific harnesses or road ABS units. Other positions are not specified here. WS and WP and their black/white wire descriptions are retained as printed; do not infer sensor polarity from the names alone. Check the original drawing for connector orientation, wiring options and electrical protection.

ECU pinFunction in the cited diagram
1VBat motor relay; S1 fuse 40 A
2Switch 1
3A_GND for pressure sensor
4ABS warning lamp
5VB switch
6WS front right, black
13Motor ground
14CAN low
15V_Stab +5 V
17Diagnostic K-line
18WP front right, white
19WP rear right, white
20WS rear left, black
21WP front left, white
22WS front left, black
25VBat valve relay; S2 fuse 25 A
26CAN high
27Switch 2
30Brake-light switch input (+BLS)
31WS rear right, black
32KL15 switched supply; S3 fuse 10 A
33WP rear left, white
35Brake-pressure sensor signal
38Valve ground

Source: Bosch Motorsport ABS M4 manual, section 16 and page 50. The wheel-speed interface and sensor adapters vary with the kit. The similar M5 connector is not a compatible harness: consult the respective Bosch instructions before wiring.