Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Adaptronic standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 5 to revision 5

Removed text is struck through; added text is highlighted.

Adaptronic eSel040 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-7 FC Series 5 (1989–1991) 13B single turbo. Adaptronic eSel040 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel040 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel040 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The documented connector groups are transcribed below; verify the source and connector viewpoint before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. The oil-metering pump outputs are paired as described in the comments.

Factory pinFactory functionAdaptronic functionInstallation notes4ZGrn / Red Injector (Rear Secondary)Injector Output 4—4YGrn / Blk Injector (Rear Primary)Injector Output 3—4XGrn / Wht Injector (Front Secondary)Injector Output 2—4WGrn / Red Injector (Front Primary)Injector Output 1—4VBlk / Red Oil Metering Pump 1 barAux Output 7 barInverse of 4T.4UBlk / Grn Oil Metering Pump 2 barAux Output 8 barInverse of 4S.4TBlk / Blu Oil Metering PumpAux Output 7—4SBlk / Ora Oil Metering Pump 2Aux Output 8—4RBlu / Wht Boost ControlAux Output 3—4QBlu / Grn Idle Control Solenoid ValveAux Output 2—4PWht / Blu Defogger input——4OYel / Blk Blower inputDigital Input 7Electrical load.4NGrn / Red unknown function——4MBlu / Ora PRC Solenoid Valve——4LWht / Grn Headlight inputDigital Input 8Electrical load.4KBrn Fuel pump (circuit opening) relayAux Output 5—4JAWS Solenoid Valve——4ISplit Air Solenoid Valve——4HRed Crankshaft Sensor -veSGNDSensor wires white and white/black; loom red and green.4GWht Crank Pos Sensor G (2 tooth)CAS 2 inputSensor green; loom white.4FNC——4EBlu Crank Pos Sensor NE (24 tooth)CAS 1 inputSensor red; loom blue.4DBrn / Blk Sensor GroundSGND—4CBlk Chassis GroundPGND—4BBlk / Wht Chassis GroundPGND—4ABlk / Wht Chassis GroundPGND—3PBlu / Ryel - Relief Solenoid ValveAux Output 4—3OBlu / Red Switch Solenoid ValveAux Output 1—3NBlu Port Air Solenoid Valve—Optional front-right wheel speed.3MWht Knock SensorKnock input—3LGrn Intake Air Temperature SenorMAT input—3KGrn / Ora MAF signalAux Temp—3JBrn / Red Power GNDPGND—3IBrn / Wht TPS 5VTPS 5V—3HGrn / Yel MAP signalMAP signal input—3GBlk / Grn TPS Full RangeTPS signal input—3FGrn / Red TPS Narrow RangeSVSS1Optional flex fuel or front-left wheel speed.3EGrn / Wht Coolant Temp SensorECT—3D———3CBlk Oxygen Sensor InputO2 signal Input—3BGrn / Red Sensor GNDSGND—3AGrn / Red Oil Metering Pump SensorExt In—1V / VBlu IGF ignition feedback——1U / UBrn / Yel Mileage Sensor 2——1T / TBlk / Blu brake light switchDigital Input 5—1S / SRed / Blk Fog Lamp SwitchDigital Input 6Electrical load.1R / RGrn / Blk Neutral SwitchDigital Input 2—1Q / QGrn / Red Clutch SwitchDigital Input 1—1P / PBlk / Yel Heat Hazard——1O / OBlu / Ora A/C requestDigital Input 4Inverted digital input 4; also controls A/C clutch.1N / NLtGrn / Blk Steering Pressure SensorDigital Input 3Engine load.1M / MBlu SpeedometerMVSS1Optional rear-left wheel speed.1L / LBlk / Wht A/C RelayAC Relay OutputControlled by A/C request.1K / KGrn / Red Fuel Pump Relay (Speed)——1J / JBrn / Yel Igniter Trailing selectIgniter Output 3Direct-fire conversion: rotor 2 trailing.1I / IOra Data Link ConnectorIgniter Output 4Optional rotor 2 leading ignition; diagnostic orange wire; sacrifices switch-solenoid output.1H / HBrn Igniter LeadingIgniter Output 1Direct-fire conversion: rotor 1 leading.1G / GBrn Igniter TrailingIgniter Output 2Direct-fire conversion: rotor 1 trailing.1F / FYel / Blk Data Link ConnectorMVSS2Optional rear-right wheel speed.1E / ECheck lightAux Ouptut 6—1D / DYel Data Link ConnectorCAS 3, for flex fuelDiagnostic yellow wire.1C / CBlk / Red starter interlock switch——1B / BBlk / Wht Main Relay+12 IgnitionFrom EFI relay.1A / ABlu / Red constant powerConst 12VFused battery supply.

Manufacturer photograph

Adaptronic eSel040 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 5: Adaptronic eSel040

Adaptronic eSel040 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-7 FC Series 5 (1989–1991) 13B single turbo. Adaptronic eSel040 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel040 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel040 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The documented connector groups are transcribed below; verify the source and connector viewpoint before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. The oil-metering pump outputs are paired as described in the comments.

Factory pinFactory functionAdaptronic functionInstallation notes
4ZGrn / Red Injector (Rear Secondary)Injector Output 4—
4YGrn / Blk Injector (Rear Primary)Injector Output 3—
4XGrn / Wht Injector (Front Secondary)Injector Output 2—
4WGrn / Red Injector (Front Primary)Injector Output 1—
4VBlk / Red Oil Metering Pump 1 barAux Output 7 barInverse of 4T.
4UBlk / Grn Oil Metering Pump 2 barAux Output 8 barInverse of 4S.
4TBlk / Blu Oil Metering PumpAux Output 7—
4SBlk / Ora Oil Metering Pump 2Aux Output 8—
4RBlu / Wht Boost ControlAux Output 3—
4QBlu / Grn Idle Control Solenoid ValveAux Output 2—
4PWht / Blu Defogger input——
4OYel / Blk Blower inputDigital Input 7Electrical load.
4NGrn / Red unknown function——
4MBlu / Ora PRC Solenoid Valve——
4LWht / Grn Headlight inputDigital Input 8Electrical load.
4KBrn Fuel pump (circuit opening) relayAux Output 5—
4JAWS Solenoid Valve——
4ISplit Air Solenoid Valve——
4HRed Crankshaft Sensor -veSGNDSensor wires white and white/black; loom red and green.
4GWht Crank Pos Sensor G (2 tooth)CAS 2 inputSensor green; loom white.
4FNC——
4EBlu Crank Pos Sensor NE (24 tooth)CAS 1 inputSensor red; loom blue.
4DBrn / Blk Sensor GroundSGND—
4CBlk Chassis GroundPGND—
4BBlk / Wht Chassis GroundPGND—
4ABlk / Wht Chassis GroundPGND—
3PBlu / Ryel - Relief Solenoid ValveAux Output 4—
3OBlu / Red Switch Solenoid ValveAux Output 1—
3NBlu Port Air Solenoid Valve—Optional front-right wheel speed.
3MWht Knock SensorKnock input—
3LGrn Intake Air Temperature SenorMAT input—
3KGrn / Ora MAF signalAux Temp—
3JBrn / Red Power GNDPGND—
3IBrn / Wht TPS 5VTPS 5V—
3HGrn / Yel MAP signalMAP signal input—
3GBlk / Grn TPS Full RangeTPS signal input—
3FGrn / Red TPS Narrow RangeSVSS1Optional flex fuel or front-left wheel speed.
3EGrn / Wht Coolant Temp SensorECT—
3D———
3CBlk Oxygen Sensor InputO2 signal Input—
3BGrn / Red Sensor GNDSGND—
3AGrn / Red Oil Metering Pump SensorExt In—
1V / VBlu IGF ignition feedback——
1U / UBrn / Yel Mileage Sensor 2——
1T / TBlk / Blu brake light switchDigital Input 5—
1S / SRed / Blk Fog Lamp SwitchDigital Input 6Electrical load.
1R / RGrn / Blk Neutral SwitchDigital Input 2—
1Q / QGrn / Red Clutch SwitchDigital Input 1—
1P / PBlk / Yel Heat Hazard——
1O / OBlu / Ora A/C requestDigital Input 4Inverted digital input 4; also controls A/C clutch.
1N / NLtGrn / Blk Steering Pressure SensorDigital Input 3Engine load.
1M / MBlu SpeedometerMVSS1Optional rear-left wheel speed.
1L / LBlk / Wht A/C RelayAC Relay OutputControlled by A/C request.
1K / KGrn / Red Fuel Pump Relay (Speed)——
1J / JBrn / Yel Igniter Trailing selectIgniter Output 3Direct-fire conversion: rotor 2 trailing.
1I / IOra Data Link ConnectorIgniter Output 4Optional rotor 2 leading ignition; diagnostic orange wire; sacrifices switch-solenoid output.
1H / HBrn Igniter LeadingIgniter Output 1Direct-fire conversion: rotor 1 leading.
1G / GBrn Igniter TrailingIgniter Output 2Direct-fire conversion: rotor 1 trailing.
1F / FYel / Blk Data Link ConnectorMVSS2Optional rear-right wheel speed.
1E / ECheck lightAux Ouptut 6—
1D / DYel Data Link ConnectorCAS 3, for flex fuelDiagnostic yellow wire.
1C / CBlk / Red starter interlock switch——
1B / BBlk / Wht Main Relay+12 IgnitionFrom EFI relay.
1A / ABlu / Red constant powerConst 12VFused battery supply.

Manufacturer photograph

Adaptronic eSel040 Select ECU
Adaptronic eSel040 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.
Revision 5: Adaptronic eSel040

Adaptronic eSel040 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-7 FC Series 5 (1989–1991) 13B single turbo. Adaptronic eSel040 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel040 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel040 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The documented connector groups are transcribed below; verify the source and connector viewpoint before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. The oil-metering pump outputs are paired as described in the comments.

Factory pinFactory functionAdaptronic functionInstallation notes
4ZGrn / Red Injector (Rear Secondary)Injector Output 4—
4YGrn / Blk Injector (Rear Primary)Injector Output 3—
4XGrn / Wht Injector (Front Secondary)Injector Output 2—
4WGrn / Red Injector (Front Primary)Injector Output 1—
4VBlk / Red Oil Metering Pump 1 barAux Output 7 barInverse of 4T.
4UBlk / Grn Oil Metering Pump 2 barAux Output 8 barInverse of 4S.
4TBlk / Blu Oil Metering PumpAux Output 7—
4SBlk / Ora Oil Metering Pump 2Aux Output 8—
4RBlu / Wht Boost ControlAux Output 3—
4QBlu / Grn Idle Control Solenoid ValveAux Output 2—
4PWht / Blu Defogger input——
4OYel / Blk Blower inputDigital Input 7Electrical load.
4NGrn / Red unknown function——
4MBlu / Ora PRC Solenoid Valve——
4LWht / Grn Headlight inputDigital Input 8Electrical load.
4KBrn Fuel pump (circuit opening) relayAux Output 5—
4JAWS Solenoid Valve——
4ISplit Air Solenoid Valve——
4HRed Crankshaft Sensor -veSGNDSensor wires white and white/black; loom red and green.
4GWht Crank Pos Sensor G (2 tooth)CAS 2 inputSensor green; loom white.
4FNC——
4EBlu Crank Pos Sensor NE (24 tooth)CAS 1 inputSensor red; loom blue.
4DBrn / Blk Sensor GroundSGND—
4CBlk Chassis GroundPGND—
4BBlk / Wht Chassis GroundPGND—
4ABlk / Wht Chassis GroundPGND—
3PBlu / Ryel - Relief Solenoid ValveAux Output 4—
3OBlu / Red Switch Solenoid ValveAux Output 1—
3NBlu Port Air Solenoid Valve—Optional front-right wheel speed.
3MWht Knock SensorKnock input—
3LGrn Intake Air Temperature SenorMAT input—
3KGrn / Ora MAF signalAux Temp—
3JBrn / Red Power GNDPGND—
3IBrn / Wht TPS 5VTPS 5V—
3HGrn / Yel MAP signalMAP signal input—
3GBlk / Grn TPS Full RangeTPS signal input—
3FGrn / Red TPS Narrow RangeSVSS1Optional flex fuel or front-left wheel speed.
3EGrn / Wht Coolant Temp SensorECT—
3D———
3CBlk Oxygen Sensor InputO2 signal Input—
3BGrn / Red Sensor GNDSGND—
3AGrn / Red Oil Metering Pump SensorExt In—
1V / VBlu IGF ignition feedback——
1U / UBrn / Yel Mileage Sensor 2——
1T / TBlk / Blu brake light switchDigital Input 5—
1S / SRed / Blk Fog Lamp SwitchDigital Input 6Electrical load.
1R / RGrn / Blk Neutral SwitchDigital Input 2—
1Q / QGrn / Red Clutch SwitchDigital Input 1—
1P / PBlk / Yel Heat Hazard——
1O / OBlu / Ora A/C requestDigital Input 4Inverted digital input 4; also controls A/C clutch.
1N / NLtGrn / Blk Steering Pressure SensorDigital Input 3Engine load.
1M / MBlu SpeedometerMVSS1Optional rear-left wheel speed.
1L / LBlk / Wht A/C RelayAC Relay OutputControlled by A/C request.
1K / KGrn / Red Fuel Pump Relay (Speed)——
1J / JBrn / Yel Igniter Trailing selectIgniter Output 3Direct-fire conversion: rotor 2 trailing.
1I / IOra Data Link ConnectorIgniter Output 4Optional rotor 2 leading ignition; diagnostic orange wire; sacrifices switch-solenoid output.
1H / HBrn Igniter LeadingIgniter Output 1Direct-fire conversion: rotor 1 leading.
1G / GBrn Igniter TrailingIgniter Output 2Direct-fire conversion: rotor 1 trailing.
1F / FYel / Blk Data Link ConnectorMVSS2Optional rear-right wheel speed.
1E / ECheck lightAux Ouptut 6—
1D / DYel Data Link ConnectorCAS 3, for flex fuelDiagnostic yellow wire.
1C / CBlk / Red starter interlock switch——
1B / BBlk / Wht Main Relay+12 IgnitionFrom EFI relay.
1A / ABlu / Red constant powerConst 12VFused battery supply.

Manufacturer photograph

Adaptronic eSel040 Select ECU
Adaptronic eSel040 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.