Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Adaptronic standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 4 to revision 4

Removed text is struck through; added text is highlighted.

Adaptronic eSel027 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan Skyline R34 GTT RB25DET. Adaptronic eSel027 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel027 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel027 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and resistor configuration before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

From the Adaptronic eSel027 installation guide, pages 18–22. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide. Pin 111 has a resistor-selectable connection: the guide describes R9 or R11, so confirm the board configuration.

Factory pinFactory functionAdaptronic functionComments101Injector No. 1 cylinder drive signalInjector Output 2Injectors for Cylinders 1 and 4 are paired102NC--103Injector No. 3 cylinder drive signalInjector Output 3Injectors for Cylinders 3 and 5 are paired104Variable air intake control solenoid valve control signal [RB25DE (L/B), RB25DE] Turbo pressure control solenoid valve controls [RB25DET]Aux Output 2—105Injector No. 2 cylinder drive signalInjector Output 1Injectors for Cylinders 2 and 6 are paired106*Line pressure solenoid valve control signal--107Air jet swirl control solenoid valve control signal [ RB20DE (L/B)]--108Canister purge control valve control signal--109Control unit power supply (Counter- electromotive current feedback circuit)Const 12VStraight from battery via fuse110Injector No. 5 cylinder drive signalInjector Output 3Injectors for Cylinders 3 and 5 are paired111Fuel pump terminal voltage control output signal [RB25DET]+5V outputConnected to TPS5V via R9 (0R) or to SGND by populating R11 with 0R112Injector No. 6 cylinder drive signalInjector Output 1Injectors for Cylinders 2 and 6 are paired113*Line pressure solenoid valve control signal (Dropping resistor circuit)--114Injector No. 4 cylinder drive signalInjector Output 2Injectors for Cylinders 1 and 4 are paired116Injector groundPower Ground—117Variable timing control solenoid valve control signalAux Output 3—118Heated oxygen sensor heater control signalPower GroundConnected straight to ground119*Power indicator lamp--120*Lockup solenoid valve control signal--121*Shift solenoid valve A control signal--122*Shift solenoid valve B control signal--123NC--124Injector groundPower Ground—1To Igniter for Cylinder 1Ignition output 1Plugs for Cylinders 1 and 6 are fired together in wasted spark2To Igniter for Cylinder 5Ignition output 2Plugs for Cylinders 2 and 5 are fired together in wasted spark3To Igniter for Cylinder 3Ignition output 3Plugs for Cylinders 3 and 4 are fired together in wasted spark4ECM & IGN Coil Relay Control Signal—When pin 24 has 12V, this pin is pulled low to activate the ECM & IGN coil relay5Tacho outAux Output 6—6NC--7To Igniter for Cylinder 6Ignition output 1Plugs for Cylinders 1 and 6 are fired together in wasted spark8To Igniter for Cylinder 2Ignition output 2Plugs for Cylinders 2 and 5 are fired together in wasted spark9To Igniter for Cylinder 4Ignition output 3Plugs for Cylinders 3 and 4 are fired together in wasted spark10NC--11AAC valve control signalAux Output 1—12NC--13Fuel pump relayAux Output 5—14Air conditioner control signalAux Output 4—15NC--16NC--17Malfunction indicator lampAux Output 7The Adaptronic leaves this off at all times by default, but this can be changed18NC--19NC--20Ignition switch (START) signal--21Air conditioner switch signalDigital Input 2-22Check (Diagnosis Start)--23Throttle sensor output signalTPS signalConnected to pin 3724Ignition switch (IGN) signal+12V IgnitionWhen this switches to 12V, the ECM & IGN coil relay is activated (see pin 4)25Control Unit GroundPower Ground—26Power steering oil pressure switch signalDigital Input 1—27NC--28SB (select bit) 1 signal--29Vehicle speed sensor signal (Vehicle speed sensor 2)MVSS1—30Headlamp switch signalDigital Input 3—31Ignition power supply--32Control Unit GroundPower Ground—33*Idle position switch signal--34*"1" position switch signal--35*"2" position switch signal--36NC--37Throttle opening signal [RB25DE-4WD M/T, RB25DE A/T, RB25DET]TPS output signalConnected to pin 2338*"0" position switch signal--39Neutral signal (Park/neutral position signal)Digital Input 5—40*"R" position switch signal--41*Full switch signal--42NC--43Sensor groundSensor Ground—44Crankshaft position sensor 120 deg (REF) signalCAS 2 inputConnected to pin 4545Crankshaft position sensor 120 deg (REF) signalCAS 2 inputVariable-width pulses each period, for cylinder and TDC identification46Crankshaft position sensor 1 deg (POS) signalCAS 1 input1 degree pulses for calculating ignition timing47Ring gear crankshaft position sensor signal [RB20DE (L/B)] Turbo pressure sensor signal [RB25DET]MAP signal inputTurbo pressure is connected to the external MAP sensor input (can be disconnected by removing R8)48Power supply for throttle position sensor, refrigerant pressure sensor, and turbo pressure sensor+5V output+5V power supply for sensors49Rear defogger switch signalDigital Input 4—50Heated oxygen sensor signalO2/EGO signal inputFor the GTR, this is the front O2/EGO sensor51Throttle motor sensor signal [RB25DET]--52SB (select bit) 2 signal [RB25DET A/T]--53Motor throttle switch signal [RB25DET]--54Mass airflow sensor signalMAP signal inputAFM signal pin can be used for MAP signal when fitting an external MAP sensor, populate R10 with 0R (not populated by default)55Mass airflow sensor groundSensor Ground—56Engine coolant temperature sensor signalECT signal input—57Refrigerant pressure sensor signalSpare—58*Output shaft rotation sensor signal (Vehicle speed sensor 1)--59Turbine sensor signal [RB25DET A/T]--60Oil temperature sensor signal--61NC--62Knock sensor signal 1Knock inputBoth knock sensors are connected to the one knock input63Knock sensor signal 2Knock inputBoth knock sensors are connected to the one knock input64A/T mode switch signal (POWER) [RB20DE (L/B) A/T]--65DB (data bush 1 signal [RB25DET A/T]--66DB (data bush 3 signal [RB25DET A/T]--67Control unit power supply--68*O/D Off indicator lamp--69DB (data bush 2 signal [RB25DET A/T]--70A/T mode switch signal (SNOW) [RB20DE (L/B) A/T]--71*Stop lamp switch signal--72Control unit power--73NC--74NC--75Receive (Data input to control unit)CAS 3CAS 3 for flex fuel sensor input76Transmit (Data output to control unit)MATAir temperature sensor input77NC--78Auxiliary electric fan relay control signal [RB25DE, RB25DET]Aux Output 8—79ECM TCM, TCS/ABS integrated control signal ] Multiple communication] [RB25DE A/T, RB25DET--80Battery power supply--

Manufacturer photograph

Adaptronic eSel027 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 4: Adaptronic eSel027

Adaptronic eSel027 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan Skyline R34 GTT RB25DET. Adaptronic eSel027 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel027 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel027 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and resistor configuration before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

From the Adaptronic eSel027 installation guide, pages 18–22. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide. Pin 111 has a resistor-selectable connection: the guide describes R9 or R11, so confirm the board configuration.

Factory pinFactory functionAdaptronic functionComments
101Injector No. 1 cylinder drive signalInjector Output 2Injectors for Cylinders 1 and 4 are paired
102NC--
103Injector No. 3 cylinder drive signalInjector Output 3Injectors for Cylinders 3 and 5 are paired
104Variable air intake control solenoid valve control signal [RB25DE (L/B), RB25DE] Turbo pressure control solenoid valve controls [RB25DET]Aux Output 2—
105Injector No. 2 cylinder drive signalInjector Output 1Injectors for Cylinders 2 and 6 are paired
106*Line pressure solenoid valve control signal--
107Air jet swirl control solenoid valve control signal [ RB20DE (L/B)]--
108Canister purge control valve control signal--
109Control unit power supply (Counter- electromotive current feedback circuit)Const 12VStraight from battery via fuse
110Injector No. 5 cylinder drive signalInjector Output 3Injectors for Cylinders 3 and 5 are paired
111Fuel pump terminal voltage control output signal [RB25DET]+5V outputConnected to TPS5V via R9 (0R) or to SGND by populating R11 with 0R
112Injector No. 6 cylinder drive signalInjector Output 1Injectors for Cylinders 2 and 6 are paired
113*Line pressure solenoid valve control signal (Dropping resistor circuit)--
114Injector No. 4 cylinder drive signalInjector Output 2Injectors for Cylinders 1 and 4 are paired
116Injector groundPower Ground—
117Variable timing control solenoid valve control signalAux Output 3—
118Heated oxygen sensor heater control signalPower GroundConnected straight to ground
119*Power indicator lamp--
120*Lockup solenoid valve control signal--
121*Shift solenoid valve A control signal--
122*Shift solenoid valve B control signal--
123NC--
124Injector groundPower Ground—
1To Igniter for Cylinder 1Ignition output 1Plugs for Cylinders 1 and 6 are fired together in wasted spark
2To Igniter for Cylinder 5Ignition output 2Plugs for Cylinders 2 and 5 are fired together in wasted spark
3To Igniter for Cylinder 3Ignition output 3Plugs for Cylinders 3 and 4 are fired together in wasted spark
4ECM & IGN Coil Relay Control Signal—When pin 24 has 12V, this pin is pulled low to activate the ECM & IGN coil relay
5Tacho outAux Output 6—
6NC--
7To Igniter for Cylinder 6Ignition output 1Plugs for Cylinders 1 and 6 are fired together in wasted spark
8To Igniter for Cylinder 2Ignition output 2Plugs for Cylinders 2 and 5 are fired together in wasted spark
9To Igniter for Cylinder 4Ignition output 3Plugs for Cylinders 3 and 4 are fired together in wasted spark
10NC--
11AAC valve control signalAux Output 1—
12NC--
13Fuel pump relayAux Output 5—
14Air conditioner control signalAux Output 4—
15NC--
16NC--
17Malfunction indicator lampAux Output 7The Adaptronic leaves this off at all times by default, but this can be changed
18NC--
19NC--
20Ignition switch (START) signal--
21Air conditioner switch signalDigital Input 2-
22Check (Diagnosis Start)--
23Throttle sensor output signalTPS signalConnected to pin 37
24Ignition switch (IGN) signal+12V IgnitionWhen this switches to 12V, the ECM & IGN coil relay is activated (see pin 4)
25Control Unit GroundPower Ground—
26Power steering oil pressure switch signalDigital Input 1—
27NC--
28SB (select bit) 1 signal--
29Vehicle speed sensor signal (Vehicle speed sensor 2)MVSS1—
30Headlamp switch signalDigital Input 3—
31Ignition power supply--
32Control Unit GroundPower Ground—
33*Idle position switch signal--
34*"1" position switch signal--
35*"2" position switch signal--
36NC--
37Throttle opening signal [RB25DE-4WD M/T, RB25DE A/T, RB25DET]TPS output signalConnected to pin 23
38*"0" position switch signal--
39Neutral signal (Park/neutral position signal)Digital Input 5—
40*"R" position switch signal--
41*Full switch signal--
42NC--
43Sensor groundSensor Ground—
44Crankshaft position sensor 120 deg (REF) signalCAS 2 inputConnected to pin 45
45Crankshaft position sensor 120 deg (REF) signalCAS 2 inputVariable-width pulses each period, for cylinder and TDC identification
46Crankshaft position sensor 1 deg (POS) signalCAS 1 input1 degree pulses for calculating ignition timing
47Ring gear crankshaft position sensor signal [RB20DE (L/B)] Turbo pressure sensor signal [RB25DET]MAP signal inputTurbo pressure is connected to the external MAP sensor input (can be disconnected by removing R8)
48Power supply for throttle position sensor, refrigerant pressure sensor, and turbo pressure sensor+5V output+5V power supply for sensors
49Rear defogger switch signalDigital Input 4—
50Heated oxygen sensor signalO2/EGO signal inputFor the GTR, this is the front O2/EGO sensor
51Throttle motor sensor signal [RB25DET]--
52SB (select bit) 2 signal [RB25DET A/T]--
53Motor throttle switch signal [RB25DET]--
54Mass airflow sensor signalMAP signal inputAFM signal pin can be used for MAP signal when fitting an external MAP sensor, populate R10 with 0R (not populated by default)
55Mass airflow sensor groundSensor Ground—
56Engine coolant temperature sensor signalECT signal input—
57Refrigerant pressure sensor signalSpare—
58*Output shaft rotation sensor signal (Vehicle speed sensor 1)--
59Turbine sensor signal [RB25DET A/T]--
60Oil temperature sensor signal--
61NC--
62Knock sensor signal 1Knock inputBoth knock sensors are connected to the one knock input
63Knock sensor signal 2Knock inputBoth knock sensors are connected to the one knock input
64A/T mode switch signal (POWER) [RB20DE (L/B) A/T]--
65DB (data bush 1 signal [RB25DET A/T]--
66DB (data bush 3 signal [RB25DET A/T]--
67Control unit power supply--
68*O/D Off indicator lamp--
69DB (data bush 2 signal [RB25DET A/T]--
70A/T mode switch signal (SNOW) [RB20DE (L/B) A/T]--
71*Stop lamp switch signal--
72Control unit power--
73NC--
74NC--
75Receive (Data input to control unit)CAS 3CAS 3 for flex fuel sensor input
76Transmit (Data output to control unit)MATAir temperature sensor input
77NC--
78Auxiliary electric fan relay control signal [RB25DE, RB25DET]Aux Output 8—
79ECM TCM, TCS/ABS integrated control signal ] Multiple communication] [RB25DE A/T, RB25DET--
80Battery power supply--

Manufacturer photograph

Adaptronic eSel027 Select ECU
Adaptronic eSel027 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.
Revision 4: Adaptronic eSel027

Adaptronic eSel027 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan Skyline R34 GTT RB25DET. Adaptronic eSel027 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel027 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel027 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and resistor configuration before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

From the Adaptronic eSel027 installation guide, pages 18–22. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide. Pin 111 has a resistor-selectable connection: the guide describes R9 or R11, so confirm the board configuration.

Factory pinFactory functionAdaptronic functionComments
101Injector No. 1 cylinder drive signalInjector Output 2Injectors for Cylinders 1 and 4 are paired
102NC--
103Injector No. 3 cylinder drive signalInjector Output 3Injectors for Cylinders 3 and 5 are paired
104Variable air intake control solenoid valve control signal [RB25DE (L/B), RB25DE] Turbo pressure control solenoid valve controls [RB25DET]Aux Output 2—
105Injector No. 2 cylinder drive signalInjector Output 1Injectors for Cylinders 2 and 6 are paired
106*Line pressure solenoid valve control signal--
107Air jet swirl control solenoid valve control signal [ RB20DE (L/B)]--
108Canister purge control valve control signal--
109Control unit power supply (Counter- electromotive current feedback circuit)Const 12VStraight from battery via fuse
110Injector No. 5 cylinder drive signalInjector Output 3Injectors for Cylinders 3 and 5 are paired
111Fuel pump terminal voltage control output signal [RB25DET]+5V outputConnected to TPS5V via R9 (0R) or to SGND by populating R11 with 0R
112Injector No. 6 cylinder drive signalInjector Output 1Injectors for Cylinders 2 and 6 are paired
113*Line pressure solenoid valve control signal (Dropping resistor circuit)--
114Injector No. 4 cylinder drive signalInjector Output 2Injectors for Cylinders 1 and 4 are paired
116Injector groundPower Ground—
117Variable timing control solenoid valve control signalAux Output 3—
118Heated oxygen sensor heater control signalPower GroundConnected straight to ground
119*Power indicator lamp--
120*Lockup solenoid valve control signal--
121*Shift solenoid valve A control signal--
122*Shift solenoid valve B control signal--
123NC--
124Injector groundPower Ground—
1To Igniter for Cylinder 1Ignition output 1Plugs for Cylinders 1 and 6 are fired together in wasted spark
2To Igniter for Cylinder 5Ignition output 2Plugs for Cylinders 2 and 5 are fired together in wasted spark
3To Igniter for Cylinder 3Ignition output 3Plugs for Cylinders 3 and 4 are fired together in wasted spark
4ECM & IGN Coil Relay Control Signal—When pin 24 has 12V, this pin is pulled low to activate the ECM & IGN coil relay
5Tacho outAux Output 6—
6NC--
7To Igniter for Cylinder 6Ignition output 1Plugs for Cylinders 1 and 6 are fired together in wasted spark
8To Igniter for Cylinder 2Ignition output 2Plugs for Cylinders 2 and 5 are fired together in wasted spark
9To Igniter for Cylinder 4Ignition output 3Plugs for Cylinders 3 and 4 are fired together in wasted spark
10NC--
11AAC valve control signalAux Output 1—
12NC--
13Fuel pump relayAux Output 5—
14Air conditioner control signalAux Output 4—
15NC--
16NC--
17Malfunction indicator lampAux Output 7The Adaptronic leaves this off at all times by default, but this can be changed
18NC--
19NC--
20Ignition switch (START) signal--
21Air conditioner switch signalDigital Input 2-
22Check (Diagnosis Start)--
23Throttle sensor output signalTPS signalConnected to pin 37
24Ignition switch (IGN) signal+12V IgnitionWhen this switches to 12V, the ECM & IGN coil relay is activated (see pin 4)
25Control Unit GroundPower Ground—
26Power steering oil pressure switch signalDigital Input 1—
27NC--
28SB (select bit) 1 signal--
29Vehicle speed sensor signal (Vehicle speed sensor 2)MVSS1—
30Headlamp switch signalDigital Input 3—
31Ignition power supply--
32Control Unit GroundPower Ground—
33*Idle position switch signal--
34*"1" position switch signal--
35*"2" position switch signal--
36NC--
37Throttle opening signal [RB25DE-4WD M/T, RB25DE A/T, RB25DET]TPS output signalConnected to pin 23
38*"0" position switch signal--
39Neutral signal (Park/neutral position signal)Digital Input 5—
40*"R" position switch signal--
41*Full switch signal--
42NC--
43Sensor groundSensor Ground—
44Crankshaft position sensor 120 deg (REF) signalCAS 2 inputConnected to pin 45
45Crankshaft position sensor 120 deg (REF) signalCAS 2 inputVariable-width pulses each period, for cylinder and TDC identification
46Crankshaft position sensor 1 deg (POS) signalCAS 1 input1 degree pulses for calculating ignition timing
47Ring gear crankshaft position sensor signal [RB20DE (L/B)] Turbo pressure sensor signal [RB25DET]MAP signal inputTurbo pressure is connected to the external MAP sensor input (can be disconnected by removing R8)
48Power supply for throttle position sensor, refrigerant pressure sensor, and turbo pressure sensor+5V output+5V power supply for sensors
49Rear defogger switch signalDigital Input 4—
50Heated oxygen sensor signalO2/EGO signal inputFor the GTR, this is the front O2/EGO sensor
51Throttle motor sensor signal [RB25DET]--
52SB (select bit) 2 signal [RB25DET A/T]--
53Motor throttle switch signal [RB25DET]--
54Mass airflow sensor signalMAP signal inputAFM signal pin can be used for MAP signal when fitting an external MAP sensor, populate R10 with 0R (not populated by default)
55Mass airflow sensor groundSensor Ground—
56Engine coolant temperature sensor signalECT signal input—
57Refrigerant pressure sensor signalSpare—
58*Output shaft rotation sensor signal (Vehicle speed sensor 1)--
59Turbine sensor signal [RB25DET A/T]--
60Oil temperature sensor signal--
61NC--
62Knock sensor signal 1Knock inputBoth knock sensors are connected to the one knock input
63Knock sensor signal 2Knock inputBoth knock sensors are connected to the one knock input
64A/T mode switch signal (POWER) [RB20DE (L/B) A/T]--
65DB (data bush 1 signal [RB25DET A/T]--
66DB (data bush 3 signal [RB25DET A/T]--
67Control unit power supply--
68*O/D Off indicator lamp--
69DB (data bush 2 signal [RB25DET A/T]--
70A/T mode switch signal (SNOW) [RB20DE (L/B) A/T]--
71*Stop lamp switch signal--
72Control unit power--
73NC--
74NC--
75Receive (Data input to control unit)CAS 3CAS 3 for flex fuel sensor input
76Transmit (Data output to control unit)MATAir temperature sensor input
77NC--
78Auxiliary electric fan relay control signal [RB25DE, RB25DET]Aux Output 8—
79ECM TCM, TCS/ABS integrated control signal ] Multiple communication] [RB25DE A/T, RB25DET--
80Battery power supply--

Manufacturer photograph

Adaptronic eSel027 Select ECU
Adaptronic eSel027 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.