Adaptronic eSel022 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-7 FD Series 8 13B REW twin turbo. Adaptronic eSel022 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel022 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel022 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer's connector schedule is reproduced below; use the correct drawing and connector viewpoint rather than borrowing a table from another Select or eMod ECU.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Manufacturer connector table
From the Adaptronic eSel022 installation guide, pages 33–35. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide.
| Factory pin | Factory function | Adaptronic function | Comments |
|---|---|---|---|
| 4A | EGI Main relay | +12V Ignition | When this switches to 12V, the EGI main relay is activated |
| 4B | Battery | Const 12V | — |
| 4C | IG SW | — | — |
| 4D | A / P relay | — | — |
| 4E | DLC (+B) EGI main relay | — | — |
| 4F | fuel pump relay (speed) | PGND | — |
| 4G | Circuit Opening relay / Fuel pump relay | Aux Output 5 | — |
| 4H | TNS relay | — | — |
| 4I | A/C relay | AC Relay Output | — |
| 4K | Electric fan relay no.2 and no.4 | Aux Output 6 | — |
| 4L | Electric fan relay no.3 | Aux Output 6 | — |
| 4M | DLC (IG-) PCM engine (rpm signal) | Tacho Out | — |
| 4O | DLC (TEN) PCM engine | Igniter Output 4 | — |
| 4P | 96-98 (heat warning light) 99- (-) | — | — |
| 4Q | speedometer sensor | MVSS1 | — |
| 4R | - | — | — |
| 4S | Clutch switch | Digital Input 1 | — |
| 4U | - | — | — |
| 4V | A/C switch | Digital Input 4 | — |
| 4W | P / S pressure switch | Digital Input 3 | — |
| 4Y | DLC (MEN) PCM engine | CAS3 | Flex fuel sensor input |
| 4AA | Stoplight switch | Digital Input 5 | — |
| 4AB | A / C Amplifier | — | — |
| 4AC | Parking light | Digital input 8 | — |
| 4AE | Rear defroster | — | — |
| 4AF | Igniter IGT - TF | Igniter Output 2 | — |
| 4AG | A/C Thermoswitch | — | — |
| 4AH | MAP / boost sensor | MAP signal input | There is already a MAP sensor on the engine |
| 4AI | DLC (FEN) PCM engine | — | — |
| 4AJ | Igniter IGT - TR | Igniter Output 3 | — |
| 4AK | - | MVSS2 | — |
| 4AL | - | SVSS1 | — |
| 4AM | - | SVSS2 | — |
| 4AN | Igniter IGT-L | Igniter Output 1 | — |
| 3A | TPS constant | TPS 5V | — |
| 3B | ß | — | — |
| 3C | Neutral switch | Digital Input 2 | — |
| 3D | O2 sensor | O2 signal input | — |
| 3E | - | Digital input 6 | — |
| 3F | - | Digital input 7 | — |
| 3G | fuel pressure regulator solenoid | — | — |
| 3H | oil metering pump sensor | Ext In | — |
| 3I | TPS (full range) | TPS signal input | — |
| 3K | TPS (narrow range) | — | — |
| 3M | - | — | — |
| 3O | Knock sensor | Knock input | — |
| 3Q | Double throttle control solenoid | — | — |
| 3R | Crank angle sensor (Ne+) | CAS 1 input | — |
| 3S | Crank angle sensor (G-) | SGND | — |
| 3T | Intake air temperature sensor | MAT input | — |
| 3U | Crank angle sensor (G+) | CAS 2 input | — |
| 3V | Fuel temperature sensor | Aux Temp | This is not used by the ECU for tuning. Therefore it can be used for oil temerature input for logging or a race dash. |
| 3W | Water temperature sensor | ECT | — |
| 3X | - | — | — |
| 3Z | - | — | — |
| 3AB | Ground (input) | SGND | — |
| 1A | - | — | — |
| 1B | - | — | — |
| 1C | Idle speed control solenoid | Aux Output 2 | — |
| 1D | Port Air control solenoid | — | — |
| 1E | Charge control solenoid | Inverse Aux output 4 | — |
| 1F | Secondary air relief/bypass valve | — | — |
| 1G | Purge control solenoid | — | — |
| 1H | Electric fan relay No.1 | Aux Output 6 | — |
| 1I | Charge relief solenoid | Aux Output 4 | — |
| 1K | Turbo pre-control solenoid | Aux Output 1 | — |
| 1L | Ground (CPU) | PGND | — |
| 1M | Turbo control solenoid | Aux Output 4 | — |
| 1O | Wastegate control solenoid | Aux Output 3 | — |
| 1Q | Injector (FP) | Injector Output 1 | — |
| 1R | - | — | — |
| 1S | Stepping motor 1 metering oil pump | Aux Output 7 | — |
| 1U | Injector (RP) | Injector Output 3 | — |
| 1W | Stepping motor 2 metering oil pump | Aux Output 8 | — |
| 1X | Ground (output) | PGND | — |
| 1Y | Injector (FS) | Injector Output 2 | — |
| 1AA | Stepping motor 3 metering oil pump | Aux Output 7 bar | — |
| 1AB | Ground (output) | PGND | — |
| 1AC | Injector (RS) | Injector Output 4 | — |
| 1AD | - | — | — |
| 1AE | Stepping motor 4 metering oil pump | Aux Output 8 bar | — |
| 1AF | Ground (output) | PGND | — |
| 1AH | - | — | — |
| 1AJ | Ground (output) | PGND | — |
Manufacturer photograph
