Removed text is struck through; added text is highlighted.
Adaptronic eSel020 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 240SX KA24DE and N14 Pulsar/Sunny GTi-R or SR20VE applications listed by Adaptronic. Adaptronic eSel020 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel020 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel020 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
A structured pin index with a redrawn connector face is in Adaptronic eSel020 connector pinout.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Adaptronic manufacturer index
Manufacturer connector table
From the Adaptronic eSel020 installation guide, pages 22–24. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide. Pin 106 uses AUX 7 by default; the SR20VE installation changes jumpers J6 and J7 to select AUX 3.
Factory pinFactory functionAdaptronic functionComments101Injector for cylinder 1Injector Output 3—102Purge valveAux Output 4GTiR no connection. SR20VE = VVL intake103Injector for cylinder 3Injector Output 4—104Fuel pump relayAux Output 5—105Fuel pump voltage control+5V outputConnected straight to +5V inside ECU106Aircon relayAux Output 7 - can connect to Aux 3 with jumper change inside ECUVVL exhaust on SR20VE107GroundPower Ground—108GroundPower Ground—109Constant PowerConst 12VStraight from battery via fuse110Injector for cylinder 2Injector Output 2—111Boost controlAux Output 3—112Injector for cylinder 4Injector Output 1—113Idle Control ValveAux Output 2—114NCAux Output 1Spare output115NC——116GroundPower Ground—1To IgniterIgnition output 1—2TachometerIgnition output 3—3Resistor / Condenser—Input from ignition coil - unused4ECCS relayPulled low by +12V ignition input—5NCIgnition output 2 (not used usually)—6GroundPower Ground—7Data link connectorIgnition output 4 (not used usually)—8Exhaust temperatureAux Temperature signal input—9Cooling fan relayAux Output 8—10Aircon relayAux Output 7—11NCAux Output 7A/C relay on GTiR12Auto TransmissionDigital Input 5Spare input13GroundPower Ground—14ClockExternal 0-5V inputSpare input15Data link connectorDigital Input 4Spare input16AFM signalMAP signal inputAFM signal pin can be used for MAP signal when fitting an external MAP sensor17AFM GNDSensor Ground—18Engine Coolant TemperatureECT signal input—19O2/EGO sensor signalO2/EGO signal input—20Throttle Position SensorTPS signal input—21Sensor groundSensor Ground—22180 deg Cam Angle Sensor SignalCAS 2 inputVariable-width pulses each period, for cylinder and TDC identification23Data link connectorCAS 3 inputAvailable for flex fuel input24Malfunction indicator lampAux Output 6—25Exhaust temperature warning light——26NCDigital Input 6Spare input27Knock sensor signalKnock input—28Auto TransmissionDigital Input 7Spare input29Sensor groundSensor Ground—30180 deg Cam Angle Sensor SignalCAS 2 inputConnected to pin 22311 deg Cam Angle Sensor SignalCAS 1 inputConnected to pin 4032SpeedometerMVSS1—33NCMVSS2 inputAdditional input for traction control34StarterDigital Input 8Spare input (ECU does not require starter input signal)35Neutral switchDigital Input 1—36Ignition switch+12V IgnitionAlso triggers ECCS relay output37+5V out+5V output+5V power supply for sensors38From ECCS relay—Not used by our ECU39GroundPower Ground—401 deg Cam Angle Sensor SignalCAS 1 input1 degree pulses for calculating ignition timing41Aircon request inputDigital Input 3—42Auto TransmissionSVSS1 inputAdditional input for traction control43Power steering load inputDigital Input 2—44Auto TransmissionSVSS2 inputAdditional input for traction control45Air TemperatureAir Temperature signal inputNot used on all models but the pin is available to add an air temperature sensor46Constant Power——47From ECCS relay——48GroundPower Ground—
Manufacturer photograph
Adaptronic eSel020 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 4: Adaptronic eSel020
Adaptronic eSel020 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 240SX KA24DE and N14 Pulsar/Sunny GTi-R or SR20VE applications listed by Adaptronic. Adaptronic eSel020 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel020 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel020 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
From the Adaptronic eSel020 installation guide, pages 22–24. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide. Pin 106 uses AUX 7 by default; the SR20VE installation changes jumpers J6 and J7 to select AUX 3.
Factory pin
Factory function
Adaptronic function
Comments
101
Injector for cylinder 1
Injector Output 3
—
102
Purge valve
Aux Output 4
GTiR no connection. SR20VE = VVL intake
103
Injector for cylinder 3
Injector Output 4
—
104
Fuel pump relay
Aux Output 5
—
105
Fuel pump voltage control
+5V output
Connected straight to +5V inside ECU
106
Aircon relay
Aux Output 7 - can connect to Aux 3 with jumper change inside ECU
VVL exhaust on SR20VE
107
Ground
Power Ground
—
108
Ground
Power Ground
—
109
Constant Power
Const 12V
Straight from battery via fuse
110
Injector for cylinder 2
Injector Output 2
—
111
Boost control
Aux Output 3
—
112
Injector for cylinder 4
Injector Output 1
—
113
Idle Control Valve
Aux Output 2
—
114
NC
Aux Output 1
Spare output
115
NC
—
—
116
Ground
Power Ground
—
1
To Igniter
Ignition output 1
—
2
Tachometer
Ignition output 3
—
3
Resistor / Condenser
—
Input from ignition coil - unused
4
ECCS relay
Pulled low by +12V ignition input
—
5
NC
Ignition output 2 (not used usually)
—
6
Ground
Power Ground
—
7
Data link connector
Ignition output 4 (not used usually)
—
8
Exhaust temperature
Aux Temperature signal input
—
9
Cooling fan relay
Aux Output 8
—
10
Aircon relay
Aux Output 7
—
11
NC
Aux Output 7
A/C relay on GTiR
12
Auto Transmission
Digital Input 5
Spare input
13
Ground
Power Ground
—
14
Clock
External 0-5V input
Spare input
15
Data link connector
Digital Input 4
Spare input
16
AFM signal
MAP signal input
AFM signal pin can be used for MAP signal when fitting an external MAP sensor
17
AFM GND
Sensor Ground
—
18
Engine Coolant Temperature
ECT signal input
—
19
O2/EGO sensor signal
O2/EGO signal input
—
20
Throttle Position Sensor
TPS signal input
—
21
Sensor ground
Sensor Ground
—
22
180 deg Cam Angle Sensor Signal
CAS 2 input
Variable-width pulses each period, for cylinder and TDC identification
23
Data link connector
CAS 3 input
Available for flex fuel input
24
Malfunction indicator lamp
Aux Output 6
—
25
Exhaust temperature warning light
—
—
26
NC
Digital Input 6
Spare input
27
Knock sensor signal
Knock input
—
28
Auto Transmission
Digital Input 7
Spare input
29
Sensor ground
Sensor Ground
—
30
180 deg Cam Angle Sensor Signal
CAS 2 input
Connected to pin 22
31
1 deg Cam Angle Sensor Signal
CAS 1 input
Connected to pin 40
32
Speedometer
MVSS1
—
33
NC
MVSS2 input
Additional input for traction control
34
Starter
Digital Input 8
Spare input (ECU does not require starter input signal)
35
Neutral switch
Digital Input 1
—
36
Ignition switch
+12V Ignition
Also triggers ECCS relay output
37
+5V out
+5V output
+5V power supply for sensors
38
From ECCS relay
—
Not used by our ECU
39
Ground
Power Ground
—
40
1 deg Cam Angle Sensor Signal
CAS 1 input
1 degree pulses for calculating ignition timing
41
Aircon request input
Digital Input 3
—
42
Auto Transmission
SVSS1 input
Additional input for traction control
43
Power steering load input
Digital Input 2
—
44
Auto Transmission
SVSS2 input
Additional input for traction control
45
Air Temperature
Air Temperature signal input
Not used on all models but the pin is available to add an air temperature sensor
46
Constant Power
—
—
47
From ECCS relay
—
—
48
Ground
Power Ground
—
Manufacturer photograph
Adaptronic eSel020 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.Revision 5: Adaptronic eSel020
Adaptronic eSel020 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 240SX KA24DE and N14 Pulsar/Sunny GTi-R or SR20VE applications listed by Adaptronic. Adaptronic eSel020 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel020 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel020 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
From the Adaptronic eSel020 installation guide, pages 22–24. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide. Pin 106 uses AUX 7 by default; the SR20VE installation changes jumpers J6 and J7 to select AUX 3.
Factory pin
Factory function
Adaptronic function
Comments
101
Injector for cylinder 1
Injector Output 3
—
102
Purge valve
Aux Output 4
GTiR no connection. SR20VE = VVL intake
103
Injector for cylinder 3
Injector Output 4
—
104
Fuel pump relay
Aux Output 5
—
105
Fuel pump voltage control
+5V output
Connected straight to +5V inside ECU
106
Aircon relay
Aux Output 7 - can connect to Aux 3 with jumper change inside ECU
VVL exhaust on SR20VE
107
Ground
Power Ground
—
108
Ground
Power Ground
—
109
Constant Power
Const 12V
Straight from battery via fuse
110
Injector for cylinder 2
Injector Output 2
—
111
Boost control
Aux Output 3
—
112
Injector for cylinder 4
Injector Output 1
—
113
Idle Control Valve
Aux Output 2
—
114
NC
Aux Output 1
Spare output
115
NC
—
—
116
Ground
Power Ground
—
1
To Igniter
Ignition output 1
—
2
Tachometer
Ignition output 3
—
3
Resistor / Condenser
—
Input from ignition coil - unused
4
ECCS relay
Pulled low by +12V ignition input
—
5
NC
Ignition output 2 (not used usually)
—
6
Ground
Power Ground
—
7
Data link connector
Ignition output 4 (not used usually)
—
8
Exhaust temperature
Aux Temperature signal input
—
9
Cooling fan relay
Aux Output 8
—
10
Aircon relay
Aux Output 7
—
11
NC
Aux Output 7
A/C relay on GTiR
12
Auto Transmission
Digital Input 5
Spare input
13
Ground
Power Ground
—
14
Clock
External 0-5V input
Spare input
15
Data link connector
Digital Input 4
Spare input
16
AFM signal
MAP signal input
AFM signal pin can be used for MAP signal when fitting an external MAP sensor
17
AFM GND
Sensor Ground
—
18
Engine Coolant Temperature
ECT signal input
—
19
O2/EGO sensor signal
O2/EGO signal input
—
20
Throttle Position Sensor
TPS signal input
—
21
Sensor ground
Sensor Ground
—
22
180 deg Cam Angle Sensor Signal
CAS 2 input
Variable-width pulses each period, for cylinder and TDC identification
23
Data link connector
CAS 3 input
Available for flex fuel input
24
Malfunction indicator lamp
Aux Output 6
—
25
Exhaust temperature warning light
—
—
26
NC
Digital Input 6
Spare input
27
Knock sensor signal
Knock input
—
28
Auto Transmission
Digital Input 7
Spare input
29
Sensor ground
Sensor Ground
—
30
180 deg Cam Angle Sensor Signal
CAS 2 input
Connected to pin 22
31
1 deg Cam Angle Sensor Signal
CAS 1 input
Connected to pin 40
32
Speedometer
MVSS1
—
33
NC
MVSS2 input
Additional input for traction control
34
Starter
Digital Input 8
Spare input (ECU does not require starter input signal)
35
Neutral switch
Digital Input 1
—
36
Ignition switch
+12V Ignition
Also triggers ECCS relay output
37
+5V out
+5V output
+5V power supply for sensors
38
From ECCS relay
—
Not used by our ECU
39
Ground
Power Ground
—
40
1 deg Cam Angle Sensor Signal
CAS 1 input
1 degree pulses for calculating ignition timing
41
Aircon request input
Digital Input 3
—
42
Auto Transmission
SVSS1 input
Additional input for traction control
43
Power steering load input
Digital Input 2
—
44
Auto Transmission
SVSS2 input
Additional input for traction control
45
Air Temperature
Air Temperature signal input
Not used on all models but the pin is available to add an air temperature sensor