Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Adaptronic standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Adaptronic eSel015 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan Skyline R32 and R33 GTST/GTR, R34 GTR, and Z32 300ZX/Fairlady applications listed in the manufacturer guide; R34 GTT is a different eSel027 model. Adaptronic eSel015 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel015 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel015 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector tables are transcribed below; verify hardware, jumpers and viewpoint before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector schedules

Transcribed from the Adaptronic eSel015 installation guide. Identify the 130 mm and 160 mm cases and the exact vehicle before using a schedule. For the 130 mm 300ZX application, manufacturer jumpers J8–J11 must be selected for 300ZX. The 160 mm 300ZX table leaves the Adaptronic function for pin 106 blank while its comment says it connects to +5 V; verify this apparent conflict with the manufacturer. The internal header tables are explicitly for the 160 mm model. In the vehicle-connector tables, “NC” is the source's designation for no factory loom connection; a blank Adaptronic entry means no connection to the Adaptronic ECU. A dash in the table reproduces a blank source field.

130 mm ECU fitted to Skyline

Factory pinFactory functionAdaptronic functionComments
101Injector for cylinder 1Injector Output 2Injectors for cyl 1 & 4 paired
102NC——
103Injector for cylinder 3Injector Output 3Injectors for cyl 3 & 5 paired
104Fuel pump voltage control+5V outputConnected straight to +5V
105Injector for cylinder 2Injector Output 1Injectors for cyl 2 & 6 paired
106Fuel pump voltage control (GTR)+5V outputFuel pump voltage control 2 on GTR, connected straight to +5V
107Injector groundPower Ground—
108Injector groundPower Ground—
109+12V Ignition InSwitched 12V inPower to the ECU
110Injector for cylinder 5Injector Output 3Injectors for cyl 3 & 5 paired
111NC——
112Injector for cylinder 6Injector Output 1Injectors for cyl 2 & 6 paired
113Variable valve timing (R33 GTST only)Aux Output 3Can be used as spare output on GTR and R32
114Injector for cylinder 4Injector Output 2Injectors for cyl 1 & 4 paired
115O2 sensor heater groundPower GroundConnected straight to ground
116Injector groundPower Ground—
1To Igniter for Cylinder 1Ignition output 1Plugs for 1 & 6 are fired together
2To Igniter for Cylinder 5Ignition output 2Plugs for 2 & 5 are fired together
3To Igniter for Cylinder 3Ignition output 3Plugs for 3 & 4 are fired together
4Idle Control ValveAux Output 1—
5Auto TransmissionAux Temp input—
6NCAux Output 8Electrical fan enable on GTR only, otherwise spare output
7Tacho outAux Output 6—
8NCExternal 0-5V inputCan be used as external input for 0-5V wideband O2 sensor
9Aircon relayAux Output 4—
10GroundPower Ground—
11To Igniter for Cylinder 6Ignition output 1Plugs for 1 & 6 are fired together
12To Igniter for Cylinder 2Ignition output 2Plugs for 2 & 5 are fired together
13To Igniter for Cylinder 4Ignition output 3Plugs for 3 & 4 are fired together
14Auto TransmissionDigital Input 6—
15Auto TransmissionDigital Input 7—
16ECCS relay—When pin 45 has 12V, this pin is pulled low to activate the ECCS main relay
17NCDigital Input 8—
18Fuel pump relayAux Output 5—
19Power steering load inputDigital Input 1Connects via J8
20Ignition system groundPower Ground—
21TXDAir Temp signal input on some 130mm ECUs (not connected on current ECUs)Formerly available to add air temp signal, now open circuit
22RXDAux Output 8Available as spare output
23Knock sensor 1 signal (cylinders 1-3)Knock inputBoth knock sensors are connected together
24Knock sensor 2 signal (cylinders 4-6)Knock inputBoth knock sensors are connected together
25Boost controlAux Output 2—
26AFM GNDSensor Ground—
27AFM signalMAP signal inputAFM signal pin can be used for MAP signal when fitting an external MAP sensor
28Engine Coolant TemperatureECT signal input—
29O2/EGO sensor signalO2/EGO signal inputFor the GTR, this is the front O2/EGO sensor
30Sensor groundSensor Ground—
31Clock——
32Check lightAux Output 7—
33NC——
34AFM Ground on GTRPower groundConnects via J9
35Front AFM signal on GTRNo connectionConnects via J10
36FICD solenoid input signal on R33, Air temp input on GTRAir Temp signal inputConnects via J11. Connect external air temp signal to this wire instead of the FICD input.
37NCMVSS2Available as flex fuel input or rear right wheel speed
38TPS signalTPS signal inputA scaled version of this is output on pin 56
39NCSVSS1Flex fuel or front left wheel speed
40NCSVSS2Front right wheel speed
41120 deg Cam Angle Sensor SignalCAS 2 inputVariable-width pulses each period, for cylinder and TDC identification
421 deg Cam Angle Sensor SignalCAS 1 input1 degree pulses for calculating ignition timing
43Starter——
44Neutral switchDigital Input 5—
45Ignition switch+12V IgnitionWhen this switches to 12V, the ECCS main relay is activated (see pin 16)
46Aircon request inputDigital Input 2—
47Check pin on CONSULT connectorCAS3Available as flex fuel input
48+5V out+5V output+5V power supply for TPS
49Control unit power supply——
50Control unit groundPower Ground—
51120 deg Cam Angle Sensor SignalCAS 2 inputConnected to pin 41 internally
521 deg Cam Angle Sensor SignalCAS 1 inputConnected to pin 42 internally
53Vehicle Speed SignalMVSS1Gearbox speed sensor, or rear left wheel speed
54Throttle Valve Switch——
55Rear O2 sensor (GTR)O2/EGO signal inputConnected to pin 29 internally
56Throttle sensor output signalTPS signal (scaled by jumper J6)TPS output signal to ALSD / ATESSA
57Exhaust Temperature Sensor, or throttle valve switch on GTRSensor Ground—
58Battery power supplyConstant power in—
59Control unit power supply——
60Control unit groundPower Ground—

130 mm ECU fitted to 300ZX

Factory pinFactory functionAdaptronic functionComments
101Injector for cylinder 1Injector Output 2Injectors for cyl 1 & 6 paired
102EGR Valve——
103Injector for cylinder 3Injector Output 3Injectors for cyl 2 & 3 paired
104Fuel pump voltage control+5V outputConnected straight to +5V
105Injector for cylinder 5Injector Output 1Injectors for cyl 4 & 5 paired
106NC+5V outputConnected straight to +5V
107Injector groundPower Ground—
108Injector groundPower Ground—
109+12V Ignition InSwitched 12V in—
110Injector for cylinder 2Injector Output 3Injectors for cyl 2 & 3 paired
111Pressure Regulator Control Valve——
112Injector for cylinder 4Injector Output 1Injectors for cyl 4 & 5 paired
113Variable valve timingAux Output 3—
114Injector for cylinder 6Injector Output 2Injectors for cyl 1 & 6 paired
115O2 sensor heater groundPower GroundConnected straight to ground
116Injector groundPower Ground—
1To Igniter for Cylinder 1Ignition output 1Plugs for 1 & 4 are fired together
2To Igniter for Cylinder 2Ignition output 2Plugs for 2 & 5 are fired together
3To Igniter for Cylinder 3Ignition output 3Plugs for 3 & 6 are fired together
4Idle Control ValveAux Output 1—
5Auto TransmissionAux Temp input—
6NCAux Output 8Spare output available
7Tacho outAux Output 6—
8AIV control valveExternal 0-5V inputCan be used as external input for 0-5V wideband O2 sensor
9Aircon relayAux Output 4—
10GroundPower Ground—
11To Igniter for Cylinder 4Ignition output 1Plugs for 1 & 4 are fired together
12To Igniter for Cylinder 5Ignition output 2Plugs for 2 & 5 are fired together
13To Igniter for Cylinder 6Ignition output 3Plugs for 3 & 6 are fired together
14Auto TransmissionDigital Input 6—
15Auto TransmissionDigital Input 7—
16ECCS relay—When pin 45 has 12V, this pin is pulled low to activate the ECCS main relay
17NCDigital Input 8—
18Fuel pump relayAux Output 5—
19Radiator fan relayAux Output 8Connects via J8
20Ignition system groundPower Ground—
21RXDAir Temp signal input on some 130mm ECUs (not connected on current ECUs)Formerly available to add air temp signal, now open circuit
22TXDAux Output 8Available as spare output
23Knock sensor 1 signal (cylinders 1- 3)Knock input—
24NCKnock inputNot connected on Z32
25Boost controlAux Output 2—
26AFM GNDSensor Ground—
27AFM signalMAP signal inputAFM signal pin can be used for MAP signal when fitting an external MAP sensor
28Engine Coolant TemperatureECT signal input—
29O2/EGO sensor signal right bankO2/EGO signal input—
30Sensor groundSensor Ground—
31Clock——
32Check lightAux Output 7—
33FICD solenoid input signal——
34Power steering load switchDigital input 1Connects via J9
35Fuel pump voltage control5VConnects via J10
36Fuel temperature sensorAux temp signal input—
37NCMVSS2Available as flex fuel input or rear right wheel speed
38TPS signalTPS signal input—
39NCSVSS1Flex fuel or front left wheel speed
40NCSVSS2Front right wheel speed
41120 deg Cam Angle Sensor SignalCAS 2 inputVariable-width pulses each period, for cylinder and TDC identification
421 deg Cam Angle Sensor SignalCAS 1 input1 degree pulses for calculating ignition timing
43Starter——
44Neutral switchDigital Input 5—
45Ignition switch+12V IgnitionWhen this switches to 12V, the ECCS main relay is activated (see pin 16)
46Aircon request inputDigital Input 2—
47Check pin on CONSULT connectorCAS3Available as flex fuel input
48+5V out+5V output+5V power supply for sensors
49Control unit power supply——
50Control unit groundPower Ground—
51120 deg Cam Angle Sensor SignalCAS 2 inputConnected to pin 41
521 deg Cam Angle Sensor SignalCAS 1 inputConnected to pin 42
53Vehicle Speed SignalMVSS1Gearbox speed sensor, or rear left wheel speed
54Throttle Valve Switch——
55O2 sensor (right bank)O2/EGO signal inputConnected to pin 29
56Auto TransmissionTPS signal (scaled by jumper J6)TPS output signal for Skyline (not used on the 300ZX)
57Throttle valve switchSensor Ground—
58Battery power supplyConstant power in—
59Control unit power supply——
60Control unit groundPower Ground—

160 mm ECU fitted to Z32 300ZX

Factory pinFactory functionAdaptronic functionComments
101Injector for cylinder 1Injector Output 2Injectors for Cylinders 1 and 6 are paired
102NC——
103Injector for cylinder 3Injector Output 3Injectors for Cylinders 3 and 2 are paired
104Fuel pump voltage control+5V outputConnected straight to +5V
105Injector for cylinder 5Injector Output 1Injectors for Cylinders 4 and 5 are paired
106NC—Connected straight to +5V
107Injector groundPower Ground—
108Injector groundPower Ground—
109+12V Ignition InConst 12VSwitched via ECCS relay
110Injector for cylinder 2Injector Output 3Injectors for Cylinders 2 and 3 are paired
111NC——
112Injector for cylinder 4Injector Output 1Injectors for Cylinders 4 and 5 are paired
113Variable Valve TimingAux Output 3—
114Injector for cylinder 6Injector Output 2Injectors for Cylinders 6 and 1 are paired
115O2 sensor heater groundPower GroundConnected straight to ground
116Injector groundPower Ground—
1To Igniter for Cylinder 1Ignition output 1Plugs for Cylinders 1 and 4 are fired together in wasted spark
2To Igniter for Cylinder 2Ignition output 2Plugs for Cylinders 2 and 5 are fired together in wasted spark
3To Igniter for Cylinder 3Ignition output 3Plugs for Cylinders 3 and 6 are fired together in wasted spark
4Idle Control ValveAux Output 1—
5Auto Transmission——
6NCPower GroundElectrical fan enable on GTR only, connected straight to ground so it always runs
7Tacho outAux Output 6—
8NC——
9Aircon relayAux Output 4—
10GroundPower Ground—
11To Igniter for Cylinder 4Ignition output 1Plugs for Cylinders 1 and 4 are fired together in wasted spark
12To Igniter for Cylinder 5Ignition output 2Plugs for Cylinders 2 and 5 are fired together in wasted spark
13To Igniter for Cylinder 6Ignition output 3Plugs for Cylinders 3 and 6 are fired together in wasted spark
14Auto Transmission——
15Auto Transmission——
16ECCS relay—When pin 45 has 12V, this pin is pulled low to activate the ECCS main relay
17NC——
18Fuel pump relayAux Output 5—
19Power steering load inputDigital Input 1—
20Ignition system groundPower Ground—
21TXD——
22RXD——
23Knock sensor 1 signal (cylinders 1- 3)Knock inputBoth knock sensors are connected to the one knock input
24Knock sensor 2 signal (cylinders 4- 6)Knock inputBoth knock sensors are connected to the one knock input
25Boost controlAux Output 2—
26AFM GNDSensor Ground—
27AFM signalMAP signal inputAFM signal pin can be used for MAP signal when fitting an external MAP sensor
28Engine Coolant TemperatureECT signal input—
29O2/EGO sensor signalO2/EGO signal inputFor the GTR, this is the front O2/EGO sensor
30Sensor groundSensor Ground—
31Clock——
32Check lightAux Output 7The Adaptronic leaves this off at all times by default, but this can be changed
33Check Light——
34NC—AFM ground
35NC—Front AFM signal
36FICD solenoid input signalAir Temp signal inputAir Temperature sensor
37NC——
38TPS signalTPS signal input—
39NC——
40NC——
41120 deg Cam Angle Sensor SignalCAS 2 inputVariable-width pulses each period, for cylinder and TDC identification
421 deg Cam Angle Sensor SignalCAS 1 input1 degree pulses for calculating ignition timing
43Starter——
44Neutral switchDigital Input 5—
45Ignition switch+12V IgnitionWhen this switches to 12V, the ECCS main relay is activated (see pin 16)
46Aircon request inputDigital Input 2—
47Check input——
48+5V out+5V output+5V power supply for sensors
49Control unit power supply——
50Control unit groundPower Ground—
51120 deg Cam Angle Sensor SignalCAS 2 inputConnected to pin 41
521 deg Cam Angle Sensor SignalCAS 1 inputConnected to pin 42
53Vehicle Speed SignalMVSS1—
54Throttle Valve Switch——
55NCO2/EGO signal inputSecond (rear) O2/EGO sensor on GTR only
56Throttle sensor output signalTPS signalTPS output signal to ALSD
57Exhaust Temperature SensorSensor GroundThrottle valve switch power supply on GTR only
58Battery power supply——
59Control unit power supply——
60Control unit groundPower Ground—

160 mm ECU internal 8-pin header

Header pinDescriptionComments
1Sensor 5V supply—
2Sensor Ground—
3MAP signalConnected to the Air Flow Meter signal pin (pin 27)
4Air Temperature signalTemperature sensors must be wired with one wire to sensor ground and the other wire to the ECU signal input
5MVSS1 (gearbox speed sensor, or rear left wheel sped)Connected to the one vehicle speed signal pin (pin 53)
6MVSS2 (rear right wheel speed)Also flex fuel
7SVSS1 (front left wheel speed)Also flex fuel
8SVSS2 (front right wheel speed)—

160 mm ECU internal 6-pin header

Header pinDescriptionComments
1External 0-5V input signal—
2Aux Temperature signalTemperature sensors must be wired with one wire to sensor ground and the other wire to the ECU signal input
3Aux Output 8Low current and no PWM, for things like relay coils
4Digital Input 6—
5Digital Input 7—
6Digital Input 8—

Manufacturer photograph

Adaptronic eSel015 Select ECU
Adaptronic eSel015 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.