Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
ABS / DSC
Parent
Unavailable reference hub
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Happy Cactus Garage

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

Supplier-listed candidate vehicles for the MK60 Companion retrofit interface. These are aftermarket motorsport integration applications, not original-equipment fitments. Confirm wheel-speed sensors, ring tooth counts, ABS unit, harness and configuration for the individual car. Happy Cactus Garage product and vehicle list.Supplier VR sensor examplesBMW E30, E36, E28, E34 and E32; Chevrolet Corvette C4, C5 and C6 through 2008; Toyota MR2 SW20 with factory ABS and Spyder/ZZW30; Mazda MX-5 NA/NB with factory ABS; Mazda RX-7 and non-DSC RX-8; and Ford Mustang SN95.Supplier Hall sensor examplesMazda MX-5 NC/ND, RX-8 with DSC, Ford Mustang S197/S550, Porsche 987/997+, BMW E46 2003 onward, Corvette C6 2008 onward and C7, and Subaru BRZ/Toyota FR-S/GR86. The supplier describes compatibility with most Hall sensors, not all; the 2008 C6 appears in both examples, so check the actual sensor.See the converter connector reference for assignments; do not transfer vehicle sensor wiring without checking the individual harness.These are the two 12-position connectors of the Happy Cactus Garage MK60 ABS VR/Hall Converter interface, not a generic ABS ECU pinout. The vendor links the following wiring and setup documentation from its product page. The grey A-keyed connector interfaces to the ABS module; the black B-keyed connector interfaces to the chassis. Verify keying, cavity numbers, sensor type and actual harness against the manufacturer documentation.Grey ABS-module connector, DTM06-12SA / ATM06-12SAPinFunction1Powertrain CAN low2Brake switch signal to ABS controller3Rear right wheel sensor output −4Rear left wheel sensor output −5Front right wheel sensor output −6Front left wheel sensor output −7Front left wheel sensor output +8Front right wheel sensor output +9Rear left wheel sensor output +10Rear right wheel sensor output +11Switched ignition power12Powertrain CAN highPin 2 is the conditioned brake signal to the ABS brake-switch input only. The documentation shows different ABS ECU pin assignments for MK60 and MK60E1/E5; consult its model-specific cross-reference rather than assuming the converter pin number is the ECU pin number.Black chassis connector, DTM06-12SB / ATM06-12SBPinFunction1Left front VR sensor −2Right front VR sensor −3Left rear VR sensor −4Right rear VR sensor −512 V brake-light signal input6Speedometer output, 5 V PWM7ABS/DSC fault lamp output; MK60E1/E5 only8VR input wiring shield9Right rear VR sensor +10Left rear VR sensor +11Right front VR sensor +12Left front VR sensor +The maker says the VR +/− labels follow wiring diagram convention and sensor polarity does not matter. Pin 7 fault output is for MK60E1/E5. Supported Hall configurations and tone-ring requirements must be checked in the current manufacturer setup guide. These tables do not establish a generic pinout for other conversion interfaces or ECU variants.

Page organisation changed

FieldRevision 1Revision 2
Page typeTechnical articleTechnical article
SubjectABS / DSCABS / DSC
ParentUnavailable reference hubHappy Cactus MK60 Companion ABS converter
Applies toNo ECU-specific applicabilityNo ECU-specific applicability
Tool groupsNoneNone
Vehicle makesHappy Cactus GarageHappy Cactus Garage

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Happy Cactus Garage MK60 Converter connector pinouts

These are the two 12-position connectors of the Happy Cactus Garage MK60 ABS VR/Hall Converter interface, not a generic ABS ECU pinout. The vendor links the following wiring and setup documentation from its product page. The grey A-keyed connector interfaces to the ABS module; the black B-keyed connector interfaces to the chassis. Verify keying, cavity numbers, sensor type and actual harness against the manufacturer documentation.

Grey ABS-module connector, DTM06-12SA / ATM06-12SA

PinFunction
1Powertrain CAN low
2Brake switch signal to ABS controller
3Rear right wheel sensor output −
4Rear left wheel sensor output −
5Front right wheel sensor output −
6Front left wheel sensor output −
7Front left wheel sensor output +
8Front right wheel sensor output +
9Rear left wheel sensor output +
10Rear right wheel sensor output +
11Switched ignition power
12Powertrain CAN high

Pin 2 is the conditioned brake signal to the ABS brake-switch input only. The documentation shows different ABS ECU pin assignments for MK60 and MK60E1/E5; consult its model-specific cross-reference rather than assuming the converter pin number is the ECU pin number.

Black chassis connector, DTM06-12SB / ATM06-12SB

PinFunction
1Left front VR sensor −
2Right front VR sensor −
3Left rear VR sensor −
4Right rear VR sensor −
512 V brake-light signal input
6Speedometer output, 5 V PWM
7ABS/DSC fault lamp output; MK60E1/E5 only
8VR input wiring shield
9Right rear VR sensor +
10Left rear VR sensor +
11Right front VR sensor +
12Left front VR sensor +

The maker says the VR +/− labels follow wiring diagram convention and sensor polarity does not matter. Pin 7 fault output is for MK60E1/E5. Supported Hall configurations and tone-ring requirements must be checked in the current manufacturer setup guide. These tables do not establish a generic pinout for other conversion interfaces or ECU variants.

Revision 2: Happy Cactus MK60 Companion vehicle and sensor applications

Supplier-listed candidate vehicles for the MK60 Companion retrofit interface. These are aftermarket motorsport integration applications, not original-equipment fitments. Confirm wheel-speed sensors, ring tooth counts, ABS unit, harness and configuration for the individual car. Happy Cactus Garage product and vehicle list.

Supplier VR sensor examples

BMW E30, E36, E28, E34 and E32; Chevrolet Corvette C4, C5 and C6 through 2008; Toyota MR2 SW20 with factory ABS and Spyder/ZZW30; Mazda MX-5 NA/NB with factory ABS; Mazda RX-7 and non-DSC RX-8; and Ford Mustang SN95.

Supplier Hall sensor examples

Mazda MX-5 NC/ND, RX-8 with DSC, Ford Mustang S197/S550, Porsche 987/997+, BMW E46 2003 onward, Corvette C6 2008 onward and C7, and Subaru BRZ/Toyota FR-S/GR86. The supplier describes compatibility with most Hall sensors, not all; the 2008 C6 appears in both examples, so check the actual sensor.

See the converter connector reference for assignments; do not transfer vehicle sensor wiring without checking the individual harness.