Earlier FAST Classic engine-management family, documented with a 60-pin harness, preceding XFI.
Identification and functions
FAST's manufacturer FAQ distinguishes the Classic's 60-pin harness from the 104-pin XFI 2.0 harness and states that features and options differ. The FAST Classic-to-XFI adapter drawing documents a harness conversion, not proof that Classic and XFI ECU pins are interchangeable. Verify ECU part number, configuration and corresponding Classic wiring diagram.
Wiring and support
Identify ECU part number, software version, harness and engine before connecting inputs or outputs. Exact pin functions depend on the specific unit, harness and optional drivers. FAST's software and documentation index separates its families. A missing pinout is not evidence that a related system uses the same connector.
See the FAST manufacturer index. Sources reviewed 17 November 2026.
Classic harness to XFI conversion reference — partial
The FAST XFI installation manual, PDF page 193, includes the manufacturer’s “Adapting Classic Harness for Use with XFI” drawing, revision B dated 12 April 2007. It labels the Classic computer pin and original harness connector location alongside the equivalent XFI connector. The table below transcribes the locations actually identified in that conversion drawing; it is not a complete Classic pinout, and an absent position must not be assumed unused. It applies to the depicted harness and options, not every Classic build.
The source marks H1 for both discrete cam and knock and K3 for both ignition-output alternatives; determine the actual application and harness before making connections. The XFI column identifies the destination when carrying out the specific manufacturer-described conversion; it does not indicate a common physical connector between systems.
| Classic position | Function in conversion drawing | XFI destination |
|---|---|---|
| A1 | MAP signal | C20 |
| A3 | Inductive crank signal | A4 |
| B1 | TPS signal | C21 |
| B3 | Inductive crank return | A2 |
| C1 | Coolant temperature signal | C23 |
| C3 | Inductive cam signal | A3 |
| D1 | Air temperature signal | C22 |
| D3 | Inductive cam return | A1 |
| E1 | 5 V reference | C24 |
| E2 | Analogue sensor return | C11 |
| F1 | Wideband oxygen UEGOR− | C5 |
| F2 | Wideband oxygen UEGOR+ | C4 |
| F3 | Wideband oxygen UEGOP+ | C1 |
| G1 | Wideband oxygen UEGOH− | C6 |
| G2 | Wideband oxygen UEGOS+ | C3 |
| G3 | Wideband oxygen UEGOP− | C2 |
| H1 | Discrete cam signal or knock input; diagram shows both with an asterisk | A7 or A9 |
| J2 | Ignition pickup return | A13 |
| J3 | Discrete crank signal | A8 |
| K2 | Ignition bypass output | A15 |
| K3 | TFI/EDIS or EST output; diagram shows both with a double asterisk | A10 or A14 |
| L2 | Power adder enable | B19 |
| L3 | Switched ignition input | B17 |
| M1 | Battery voltage input | B18 |
| M2 | Analogue return | B24 |
| M3 | Digital return | B8 |
| N1 | RS-232 transmit | C27 |
| N2 | RS-232 receive | C28 |
| N3 | RS-232 return | C29 |
| P1 | Idle air control A low | B13 |
| P2 | Idle air control A high | B12 |
| R1 | Idle air control B low | B15 |
| R2 | Idle air control B high | B14 |
| R3 | Fan output | B10 |
| S1 | Injector H | D16 |
| S2 | Injector D | D9 |
| S3 | Fuel pump output | B5 |
| T1 | Injector G | D14 |
| T2 | Injector C | D7 |
| T3 | Power adder output 1 | B20 |
| W1 | Injector F | D13 |
| W2 | Injector B | D4 |
| W3 | Power adder output 2 | B21 |
| X1 | Injector E | D11 |
| X2 | Injector A | D2 |
| X3 | Points ignition output | A11 |
| Y1 | Main power return | A12 |
| Y2 | Main power return | B7 |
| Y3 | Main power return | D1 |