Removed text is struck through; added text is highlighted.
Adaptronic eSel012 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 Type-X blacktop, S14a 64-pin, and S15 SR20DET applications specified in the manufacturer guide. Adaptronic eSel012 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel012 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel012 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Adaptronic manufacturer index
Manufacturer connector schedules
Transcribed from the Adaptronic eSel012 installation guide. Jumper 6, 7 and 8 select application-specific functions; consult the guide before use. The source gives numbering from the loom side, looking into the ECU. In the vehicle-connector tables, “NC” is the source's designation for no factory loom connection; a blank Adaptronic entry means no connection to the Adaptronic ECU. A dash in the table reproduces a blank source field.
Factory pinFactory functionAdaptronic functionComments101Injector for cylinder 1Injector Output 3—102Boost controlAux Output 3—103Injector for cylinder 3Injector Output 4—104Fuel pump relay (S13X)Aux Output 5—105Fuel pump speed relay (S13X), VVT (S15)Aux Output 5 or Aux Output 4Set Jumper 6 inside the ECU. By default, set to S15.106Air conditioner (S13X), fuel pump relay (S14a, S15)Aux Output 5Set Jumper 7 inside the ECU. By default, set to S15.107GroundPower Ground—108GroundPower Ground—109Constant PowerConst 12VStraight from battery via fuse110Injector for cylinder 2Injector Output 2—111VVT (S13X), O2 heater GND (S14a, S15)Aux output 4 or Power GroundSet Jumper 8 inside the ECU. By default, set to S15.112Injector for cylinder 4Injector Output 1—113Idle Control ValveAux Output 2—114VVTAux output 4 or Power Ground—115Boost controlAux Output 3—116GroundPower Ground—1To Igniter for Cylinder 1Ignition output 1—2TachometerAux Output 8—3To Igniter for Cylinder 2Ignition output 4Aux Output 1 cannot be used due to the fourth ignition output4ECCS relay—When pin 36 has 12V, this pin is pulled low to activate the ECCS main relay5To Igniter for Cylinder 3Ignition output 2—6GroundPower Ground—7RX pin (CONSULT connector)CAS 3Available as flex fuel input8NATSDigital input 5Available as external input9Cooling fan relay 1Aux Output 6—10Cooling fan relay 2Aux Output 6—11Aircon relayAux Output 7—12Auto TransmissionDigital input 6Available as external input13GroundPower Ground—14NCDigital input 7Available as external input15TX pin (CONSULT connector)External 0-5V inputAvailable as external input16AFM signalMAP signal inputAFM signal pin can be used for MAP signal when fitting an external MAP sensor17AFM GNDSensor Ground—18Engine Coolant TemperatureECT signal input—19O2/EGO sensor signalO2/EGO signal input—20Throttle Position SensorTPS signal input—21Sensor groundSensor Ground—22180 deg Cam Angle Sensor SignalCAS 2 inputConnected to pin 30 internally23RX pin (CONSULT connector)Digital input 8Available as external input24Malfunction indicator lamp——25To Igniter for Cylinder 4Ignition output 3—26NCAux temp input—27Knock sensor signalKnock input—28Auto TransmissionMVSS2Rear right wheel speed input29NCSensor Ground—30180 deg Cam Angle Sensor SignalCAS 2 inputVariable-width pulses each period, for cylinder and TDC identification311 deg Cam Angle Sensor SignalCAS 1 input1 degree pulses for calculating ignition timing32SpeedometerMVSS1Gearbox output speed or rear left wheel speed input33Electrical loadsDigital Input 4—34Starter——35Neutral switchDigital Input 1—36Ignition switch+12V IgnitionWhen this switches to 12V, the ECCS main relay is activated (see pin 4)37+5V out+5V output+5V power supply for sensors38From ECCS relay——39GroundPower Ground—401 deg Cam Angle Sensor SignalCAS 1 inputConnected to pin 31 internally41Aircon request inputDigital Input 3—42NCSVSS1Front left wheel speed input43Power steering load inputDigital Input 2—44Auto TransmissionSVSS2Front right wheel speed input45Auto TransmissionMATAir temp input46Constant Power——47From ECCS relay——48GroundPower Ground—
Manufacturer photograph
Adaptronic eSel012 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 4: Adaptronic eSel012
Adaptronic eSel012 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 Type-X blacktop, S14a 64-pin, and S15 SR20DET applications specified in the manufacturer guide. Adaptronic eSel012 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel012 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel012 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Transcribed from the Adaptronic eSel012 installation guide. Jumper 6, 7 and 8 select application-specific functions; consult the guide before use. The source gives numbering from the loom side, looking into the ECU. In the vehicle-connector tables, “NC” is the source's designation for no factory loom connection; a blank Adaptronic entry means no connection to the Adaptronic ECU. A dash in the table reproduces a blank source field.
Set Jumper 6 inside the ECU. By default, set to S15.
106
Air conditioner (S13X), fuel pump relay (S14a, S15)
Aux Output 5
Set Jumper 7 inside the ECU. By default, set to S15.
107
Ground
Power Ground
—
108
Ground
Power Ground
—
109
Constant Power
Const 12V
Straight from battery via fuse
110
Injector for cylinder 2
Injector Output 2
—
111
VVT (S13X), O2 heater GND (S14a, S15)
Aux output 4 or Power Ground
Set Jumper 8 inside the ECU. By default, set to S15.
112
Injector for cylinder 4
Injector Output 1
—
113
Idle Control Valve
Aux Output 2
—
114
VVT
Aux output 4 or Power Ground
—
115
Boost control
Aux Output 3
—
116
Ground
Power Ground
—
1
To Igniter for Cylinder 1
Ignition output 1
—
2
Tachometer
Aux Output 8
—
3
To Igniter for Cylinder 2
Ignition output 4
Aux Output 1 cannot be used due to the fourth ignition output
4
ECCS relay
—
When pin 36 has 12V, this pin is pulled low to activate the ECCS main relay
5
To Igniter for Cylinder 3
Ignition output 2
—
6
Ground
Power Ground
—
7
RX pin (CONSULT connector)
CAS 3
Available as flex fuel input
8
NATS
Digital input 5
Available as external input
9
Cooling fan relay 1
Aux Output 6
—
10
Cooling fan relay 2
Aux Output 6
—
11
Aircon relay
Aux Output 7
—
12
Auto Transmission
Digital input 6
Available as external input
13
Ground
Power Ground
—
14
NC
Digital input 7
Available as external input
15
TX pin (CONSULT connector)
External 0-5V input
Available as external input
16
AFM signal
MAP signal input
AFM signal pin can be used for MAP signal when fitting an external MAP sensor
17
AFM GND
Sensor Ground
—
18
Engine Coolant Temperature
ECT signal input
—
19
O2/EGO sensor signal
O2/EGO signal input
—
20
Throttle Position Sensor
TPS signal input
—
21
Sensor ground
Sensor Ground
—
22
180 deg Cam Angle Sensor Signal
CAS 2 input
Connected to pin 30 internally
23
RX pin (CONSULT connector)
Digital input 8
Available as external input
24
Malfunction indicator lamp
—
—
25
To Igniter for Cylinder 4
Ignition output 3
—
26
NC
Aux temp input
—
27
Knock sensor signal
Knock input
—
28
Auto Transmission
MVSS2
Rear right wheel speed input
29
NC
Sensor Ground
—
30
180 deg Cam Angle Sensor Signal
CAS 2 input
Variable-width pulses each period, for cylinder and TDC identification
31
1 deg Cam Angle Sensor Signal
CAS 1 input
1 degree pulses for calculating ignition timing
32
Speedometer
MVSS1
Gearbox output speed or rear left wheel speed input
33
Electrical loads
Digital Input 4
—
34
Starter
—
—
35
Neutral switch
Digital Input 1
—
36
Ignition switch
+12V Ignition
When this switches to 12V, the ECCS main relay is activated (see pin 4)
37
+5V out
+5V output
+5V power supply for sensors
38
From ECCS relay
—
—
39
Ground
Power Ground
—
40
1 deg Cam Angle Sensor Signal
CAS 1 input
Connected to pin 31 internally
41
Aircon request input
Digital Input 3
—
42
NC
SVSS1
Front left wheel speed input
43
Power steering load input
Digital Input 2
—
44
Auto Transmission
SVSS2
Front right wheel speed input
45
Auto Transmission
MAT
Air temp input
46
Constant Power
—
—
47
From ECCS relay
—
—
48
Ground
Power Ground
—
Manufacturer photograph
Adaptronic eSel012 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.Revision 4: Adaptronic eSel012
Adaptronic eSel012 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 Type-X blacktop, S14a 64-pin, and S15 SR20DET applications specified in the manufacturer guide. Adaptronic eSel012 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel012 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel012 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Transcribed from the Adaptronic eSel012 installation guide. Jumper 6, 7 and 8 select application-specific functions; consult the guide before use. The source gives numbering from the loom side, looking into the ECU. In the vehicle-connector tables, “NC” is the source's designation for no factory loom connection; a blank Adaptronic entry means no connection to the Adaptronic ECU. A dash in the table reproduces a blank source field.