Adaptronic eSel012 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 Type-X blacktop, S14a 64-pin, and S15 SR20DET applications specified in the manufacturer guide. Adaptronic eSel012 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel012 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel012 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Manufacturer connector schedules
Transcribed from the Adaptronic eSel012 installation guide. Jumper 6, 7 and 8 select application-specific functions; consult the guide before use. The source gives numbering from the loom side, looking into the ECU. In the vehicle-connector tables, “NC” is the source's designation for no factory loom connection; a blank Adaptronic entry means no connection to the Adaptronic ECU. A dash in the table reproduces a blank source field.
Factory connector positions: S13 Type-X / S14a / S15
| Factory pin | Factory function | Adaptronic function | Comments |
|---|---|---|---|
| 101 | Injector for cylinder 1 | Injector Output 3 | — |
| 102 | Boost control | Aux Output 3 | — |
| 103 | Injector for cylinder 3 | Injector Output 4 | — |
| 104 | Fuel pump relay (S13X) | Aux Output 5 | — |
| 105 | Fuel pump speed relay (S13X), VVT (S15) | Aux Output 5 or Aux Output 4 | Set Jumper 6 inside the ECU. By default, set to S15. |
| 106 | Air conditioner (S13X), fuel pump relay (S14a, S15) | Aux Output 5 | Set Jumper 7 inside the ECU. By default, set to S15. |
| 107 | Ground | Power Ground | — |
| 108 | Ground | Power Ground | — |
| 109 | Constant Power | Const 12V | Straight from battery via fuse |
| 110 | Injector for cylinder 2 | Injector Output 2 | — |
| 111 | VVT (S13X), O2 heater GND (S14a, S15) | Aux output 4 or Power Ground | Set Jumper 8 inside the ECU. By default, set to S15. |
| 112 | Injector for cylinder 4 | Injector Output 1 | — |
| 113 | Idle Control Valve | Aux Output 2 | — |
| 114 | VVT | Aux output 4 or Power Ground | — |
| 115 | Boost control | Aux Output 3 | — |
| 116 | Ground | Power Ground | — |
| 1 | To Igniter for Cylinder 1 | Ignition output 1 | — |
| 2 | Tachometer | Aux Output 8 | — |
| 3 | To Igniter for Cylinder 2 | Ignition output 4 | Aux Output 1 cannot be used due to the fourth ignition output |
| 4 | ECCS relay | — | When pin 36 has 12V, this pin is pulled low to activate the ECCS main relay |
| 5 | To Igniter for Cylinder 3 | Ignition output 2 | — |
| 6 | Ground | Power Ground | — |
| 7 | RX pin (CONSULT connector) | CAS 3 | Available as flex fuel input |
| 8 | NATS | Digital input 5 | Available as external input |
| 9 | Cooling fan relay 1 | Aux Output 6 | — |
| 10 | Cooling fan relay 2 | Aux Output 6 | — |
| 11 | Aircon relay | Aux Output 7 | — |
| 12 | Auto Transmission | Digital input 6 | Available as external input |
| 13 | Ground | Power Ground | — |
| 14 | NC | Digital input 7 | Available as external input |
| 15 | TX pin (CONSULT connector) | External 0-5V input | Available as external input |
| 16 | AFM signal | MAP signal input | AFM signal pin can be used for MAP signal when fitting an external MAP sensor |
| 17 | AFM GND | Sensor Ground | — |
| 18 | Engine Coolant Temperature | ECT signal input | — |
| 19 | O2/EGO sensor signal | O2/EGO signal input | — |
| 20 | Throttle Position Sensor | TPS signal input | — |
| 21 | Sensor ground | Sensor Ground | — |
| 22 | 180 deg Cam Angle Sensor Signal | CAS 2 input | Connected to pin 30 internally |
| 23 | RX pin (CONSULT connector) | Digital input 8 | Available as external input |
| 24 | Malfunction indicator lamp | — | — |
| 25 | To Igniter for Cylinder 4 | Ignition output 3 | — |
| 26 | NC | Aux temp input | — |
| 27 | Knock sensor signal | Knock input | — |
| 28 | Auto Transmission | MVSS2 | Rear right wheel speed input |
| 29 | NC | Sensor Ground | — |
| 30 | 180 deg Cam Angle Sensor Signal | CAS 2 input | Variable-width pulses each period, for cylinder and TDC identification |
| 31 | 1 deg Cam Angle Sensor Signal | CAS 1 input | 1 degree pulses for calculating ignition timing |
| 32 | Speedometer | MVSS1 | Gearbox output speed or rear left wheel speed input |
| 33 | Electrical loads | Digital Input 4 | — |
| 34 | Starter | — | — |
| 35 | Neutral switch | Digital Input 1 | — |
| 36 | Ignition switch | +12V Ignition | When this switches to 12V, the ECCS main relay is activated (see pin 4) |
| 37 | +5V out | +5V output | +5V power supply for sensors |
| 38 | From ECCS relay | — | — |
| 39 | Ground | Power Ground | — |
| 40 | 1 deg Cam Angle Sensor Signal | CAS 1 input | Connected to pin 31 internally |
| 41 | Aircon request input | Digital Input 3 | — |
| 42 | NC | SVSS1 | Front left wheel speed input |
| 43 | Power steering load input | Digital Input 2 | — |
| 44 | Auto Transmission | SVSS2 | Front right wheel speed input |
| 45 | Auto Transmission | MAT | Air temp input |
| 46 | Constant Power | — | — |
| 47 | From ECCS relay | — | — |
| 48 | Ground | Power Ground | — |
Manufacturer photograph
