Removed text is struck through; added text is highlighted.
Adaptronic eSel002 is a Select-series vehicle-specific programmable interceptor ECU that works alongside the retained factory ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-8 Series 1 (2003–2008) 13B-MSP and non-MSP RENESIS. Adaptronic eSel002 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel002 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel002 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector and header tables are transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Adaptronic manufacturer index
Manufacturer connector schedules
Transcribed from the Adaptronic eSel002 installation guide. This interceptor retains the factory ECU. The column headed ‘Still connected to factory ECU?’ identifies circuits that are factory-only or shared with both ECUs. The source gives numbering from the loom side, looking into the ECU. The headers are inside the ECU. In the vehicle-connector tables, “NC” is the source's designation for no factory loom connection; a blank Adaptronic entry means no connection to the Adaptronic ECU. A dash in the table reproduces a blank source field.
Factory vehicle connectors: RX-8 Series 1
Factory pinFactory functionAdaptronic functionStill connected to factory ECU?Comments1ANC———1BDrive-By-Wire throttle control—Yes—1CDrive-By-Wire throttle control—Yes—1DSSV switch—Yes—1ENC———1FKnock sensor -—Yes—1GKnock sensor shield—Yes—1HNC———1JThrottle position sensor 1—Yes—1KNC———1LSSV solenoid valveAux Output 4NoSecondary Side Valve1MThrottle position sensor 2—Yes—1NNC———1OAir solenoid valve—Yes—1QThrottle Position Sensor power—Yes—1RNC———1SAPV position sensor power—Yes—1TKnock sensor +Knock signal inputYes, shared with both ECUs—1USensor groundSensor GroundYes, shared with both ECUs—1VFront O2 sensor heater—Yes—1WVDI solenoid valveAux Output 3NoVariable Dynamic Intake1XNC———2ARear O2 sensor heater—Yes—2BO2 sensor ground—Yes—2CFront O2 sensor signal—Yes—2DRear (Rotor 2) secondary injectorInjector Output 4NoSecondary injectors for rotors 1 and 2 fire together2EOil Pressure switch—Yes—2FThrottle Position Sensor ground—Yes—2GFront (Rotor 1) secondary injectorInjector Output 4NoSecondary injectors for rotors 1 and 2 fire together2HSensor shields—Yes—2IGenerator control—Yes—2JRear (Rotor 2) primary injector 1Injector Output 3No—2KEngine Coolant Temperature sensorECT signal inputYes, shared with both ECUs—2MFront (Rotor 1) primary injector 1Injector Output 1No—2NOil Metering Pump switch—Yes—2ONeutral switchDigital Input 2Yes, shared with both ECUs—2PPurge solenoid valve—Yes—2QRear O2 sensor signalO2/EGO signal inputYes, shared with both ECUs—2ROil Level switch—Yes—2TGenerator control—Yes—2UEccentric shaft position sensor +CAS 1 inputYes, shared with both ECUsReluctor trigger for ignition timing2VOil Metering Pump—Yes—2WOil Metering Pump—Yes—2XEccentric shaft position sensor -—Yes—2YOil Metering Pump—Yes—2ZRear (Rotor 2) leading ignitionIgnition output 4NoAux Output 1 cannot be used due to the fourth ignition output2AAFront (Rotor 1) leading ignitionIgnition output 1No—2ABOil Metering Pump—Yes—2ACRear (Rotor 2) trailing ignitionIgnition output 3No—2ADFront (Rotor 1) trailing ignitionIgnition output 2No—3AFront (Rotor 1) primary 2 injectorInjector Output 2NoThe Adaptronic ECU fires both primary 2 injectors together3BAPV position sensor0-5V Ext/Spare inputYes—3CNC———3DRear (Rotor 2) primary 2 injectorInjector Output 2NoThe Adaptronic ECU fires both primary 2 injectors together3ENC———3FNC———3GAPV motor controlControlled by Aux Output 7 via additional high current circuitry inside the Adaptronic ECUNoAuxiliary Port Valve3H————3I————3JAPV motor controlControlled by Aux Output 8 via additional high current circuitry inside the Adaptronic ECUNoAuxiliary Port Valve3KNC———3MNC———3NNC———3ONC———3PNC———3QNC———3RNC———4AGroundPower GroundYes, shared with both ECUs—4BNC———4CPower from Drive-By- Wire relay—Yes—4DNC———4EMain Relay enable—Yes—4FClutch switchDigital Input 1Yes, shared with both ECUs—4HNC———4INC———4JGroundPower GroundYes, shared with both ECUs—4KBarometric sensor power—Yes—4LNC———4MFuel pump speed control—Yes—4NNC———4OAir pump relay—Yes—4PBrake switch—Yes—4QIgnition switch+12V IgnitionYes, shared with both ECUs—4SCAN low—Yes—4TCoolant Level switch—Yes—4USensor ground—Yes—4VCAN high—Yes—4WHigh/Low A/C control—Yes—4XAPP sensor power 2—Yes—4YAPP sensor power 1—Yes—4ZMedium A/C control—Yes—5AStarter—Yes—5BNC———5CAPP sensor 2—Yes—5DGroundPower GroundYes, shared with both ECUs—5ENC———5FAPP sensor 1Aux temp inputYes—5HDrive-By-Wire relay—Yes—5INC———5JConstant power—Yes—5KIntake air temperature sensorAir Temp signal inputYes, shared with both ECUs—5LFuel pump relay—Yes—5MNC———5NAir flow meter signalMAP signal inputYes, shared with both ECUsAFM signal pin can be used for MAP signal when fitting an external MAP sensor5OGroundPower GroundYes, shared with both ECUs—5PFuel pump relay—Yes—5RGroundPower GroundYes, shared with both ECUs—5SBarometric pressure sensor—Yes—5TGroundPower GroundYes, shared with both ECUs—5UIntake air temperature sensor ground—Yes—5VCruise control switch—Yes—5WA/C amplifier—Yes—5XCooling fan relay 1—Yes—5ZVFAD solenoid valveAux Output 2NoVariable Fresh Air Duct5AAAircon relay—Yes—5ABAPP sensor ground 2—Yes—5ACPower from Main Relay—Yes—5ADCooling fan relays 2 and 3—Yes—5AEAPP sensor ground 1—Yes—5AFPower from Main Relay—Yes—5AGNC———5AHNC———
Internal 8-pin header
Header pinDescriptionComments1Sensor 5V supply—2Sensor Ground—3MAP signalConnected to the Air Flow Meter signal pin (pin 5N)4Air Temperature signalConnected to pin 5K5MVSS1 (master vehicle speed sensor 1)—6MVSS2 (master vehicle speed sensor 2)—7SVSS1 (slave vehicle speed sensor 1)—8SVSS2 (slave vehicle speed sensor 2)—
Internal 6-pin header
Header pinDescriptionComments1CAS3Can be used for flex fuel sensor input2Aux Temperature signalTemperature sensors must be wired with one wire
to sensor ground and the other wire to the ECU
signal input3Aux Output 5Low current, only suitable for low current loads
such as relay coils4Aux Output 6Low current, only suitable for low current loads
such as relay coils5Digital Input 7—6Digital Input 8—
Manufacturer photograph
Adaptronic eSel002 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 4: Adaptronic eSel002
Adaptronic eSel002 is a Select-series vehicle-specific programmable interceptor ECU that works alongside the retained factory ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-8 Series 1 (2003–2008) 13B-MSP and non-MSP RENESIS. Adaptronic eSel002 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel002 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel002 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector and header tables are transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Transcribed from the Adaptronic eSel002 installation guide. This interceptor retains the factory ECU. The column headed ‘Still connected to factory ECU?’ identifies circuits that are factory-only or shared with both ECUs. The source gives numbering from the loom side, looking into the ECU. The headers are inside the ECU. In the vehicle-connector tables, “NC” is the source's designation for no factory loom connection; a blank Adaptronic entry means no connection to the Adaptronic ECU. A dash in the table reproduces a blank source field.
Factory vehicle connectors: RX-8 Series 1
Factory pin
Factory function
Adaptronic function
Still connected to factory ECU?
Comments
1A
NC
—
—
—
1B
Drive-By-Wire throttle control
—
Yes
—
1C
Drive-By-Wire throttle control
—
Yes
—
1D
SSV switch
—
Yes
—
1E
NC
—
—
—
1F
Knock sensor -
—
Yes
—
1G
Knock sensor shield
—
Yes
—
1H
NC
—
—
—
1J
Throttle position sensor 1
—
Yes
—
1K
NC
—
—
—
1L
SSV solenoid valve
Aux Output 4
No
Secondary Side Valve
1M
Throttle position sensor 2
—
Yes
—
1N
NC
—
—
—
1O
Air solenoid valve
—
Yes
—
1Q
Throttle Position Sensor power
—
Yes
—
1R
NC
—
—
—
1S
APV position sensor power
—
Yes
—
1T
Knock sensor +
Knock signal input
Yes, shared with both ECUs
—
1U
Sensor ground
Sensor Ground
Yes, shared with both ECUs
—
1V
Front O2 sensor heater
—
Yes
—
1W
VDI solenoid valve
Aux Output 3
No
Variable Dynamic Intake
1X
NC
—
—
—
2A
Rear O2 sensor heater
—
Yes
—
2B
O2 sensor ground
—
Yes
—
2C
Front O2 sensor signal
—
Yes
—
2D
Rear (Rotor 2) secondary injector
Injector Output 4
No
Secondary injectors for rotors 1 and 2 fire together
2E
Oil Pressure switch
—
Yes
—
2F
Throttle Position Sensor ground
—
Yes
—
2G
Front (Rotor 1) secondary injector
Injector Output 4
No
Secondary injectors for rotors 1 and 2 fire together
2H
Sensor shields
—
Yes
—
2I
Generator control
—
Yes
—
2J
Rear (Rotor 2) primary injector 1
Injector Output 3
No
—
2K
Engine Coolant Temperature sensor
ECT signal input
Yes, shared with both ECUs
—
2M
Front (Rotor 1) primary injector 1
Injector Output 1
No
—
2N
Oil Metering Pump switch
—
Yes
—
2O
Neutral switch
Digital Input 2
Yes, shared with both ECUs
—
2P
Purge solenoid valve
—
Yes
—
2Q
Rear O2 sensor signal
O2/EGO signal input
Yes, shared with both ECUs
—
2R
Oil Level switch
—
Yes
—
2T
Generator control
—
Yes
—
2U
Eccentric shaft position sensor +
CAS 1 input
Yes, shared with both ECUs
Reluctor trigger for ignition timing
2V
Oil Metering Pump
—
Yes
—
2W
Oil Metering Pump
—
Yes
—
2X
Eccentric shaft position sensor -
—
Yes
—
2Y
Oil Metering Pump
—
Yes
—
2Z
Rear (Rotor 2) leading ignition
Ignition output 4
No
Aux Output 1 cannot be used due to the fourth ignition output
2AA
Front (Rotor 1) leading ignition
Ignition output 1
No
—
2AB
Oil Metering Pump
—
Yes
—
2AC
Rear (Rotor 2) trailing ignition
Ignition output 3
No
—
2AD
Front (Rotor 1) trailing ignition
Ignition output 2
No
—
3A
Front (Rotor 1) primary 2 injector
Injector Output 2
No
The Adaptronic ECU fires both primary 2 injectors together
3B
APV position sensor
0-5V Ext/Spare input
Yes
—
3C
NC
—
—
—
3D
Rear (Rotor 2) primary 2 injector
Injector Output 2
No
The Adaptronic ECU fires both primary 2 injectors together
3E
NC
—
—
—
3F
NC
—
—
—
3G
APV motor control
Controlled by Aux Output 7 via additional high current circuitry inside the Adaptronic ECU
No
Auxiliary Port Valve
3H
—
—
—
—
3I
—
—
—
—
3J
APV motor control
Controlled by Aux Output 8 via additional high current circuitry inside the Adaptronic ECU
No
Auxiliary Port Valve
3K
NC
—
—
—
3M
NC
—
—
—
3N
NC
—
—
—
3O
NC
—
—
—
3P
NC
—
—
—
3Q
NC
—
—
—
3R
NC
—
—
—
4A
Ground
Power Ground
Yes, shared with both ECUs
—
4B
NC
—
—
—
4C
Power from Drive-By- Wire relay
—
Yes
—
4D
NC
—
—
—
4E
Main Relay enable
—
Yes
—
4F
Clutch switch
Digital Input 1
Yes, shared with both ECUs
—
4H
NC
—
—
—
4I
NC
—
—
—
4J
Ground
Power Ground
Yes, shared with both ECUs
—
4K
Barometric sensor power
—
Yes
—
4L
NC
—
—
—
4M
Fuel pump speed control
—
Yes
—
4N
NC
—
—
—
4O
Air pump relay
—
Yes
—
4P
Brake switch
—
Yes
—
4Q
Ignition switch
+12V Ignition
Yes, shared with both ECUs
—
4S
CAN low
—
Yes
—
4T
Coolant Level switch
—
Yes
—
4U
Sensor ground
—
Yes
—
4V
CAN high
—
Yes
—
4W
High/Low A/C control
—
Yes
—
4X
APP sensor power 2
—
Yes
—
4Y
APP sensor power 1
—
Yes
—
4Z
Medium A/C control
—
Yes
—
5A
Starter
—
Yes
—
5B
NC
—
—
—
5C
APP sensor 2
—
Yes
—
5D
Ground
Power Ground
Yes, shared with both ECUs
—
5E
NC
—
—
—
5F
APP sensor 1
Aux temp input
Yes
—
5H
Drive-By-Wire relay
—
Yes
—
5I
NC
—
—
—
5J
Constant power
—
Yes
—
5K
Intake air temperature sensor
Air Temp signal input
Yes, shared with both ECUs
—
5L
Fuel pump relay
—
Yes
—
5M
NC
—
—
—
5N
Air flow meter signal
MAP signal input
Yes, shared with both ECUs
AFM signal pin can be used for MAP signal when fitting an external MAP sensor
5O
Ground
Power Ground
Yes, shared with both ECUs
—
5P
Fuel pump relay
—
Yes
—
5R
Ground
Power Ground
Yes, shared with both ECUs
—
5S
Barometric pressure sensor
—
Yes
—
5T
Ground
Power Ground
Yes, shared with both ECUs
—
5U
Intake air temperature sensor ground
—
Yes
—
5V
Cruise control switch
—
Yes
—
5W
A/C amplifier
—
Yes
—
5X
Cooling fan relay 1
—
Yes
—
5Z
VFAD solenoid valve
Aux Output 2
No
Variable Fresh Air Duct
5AA
Aircon relay
—
Yes
—
5AB
APP sensor ground 2
—
Yes
—
5AC
Power from Main Relay
—
Yes
—
5AD
Cooling fan relays 2 and 3
—
Yes
—
5AE
APP sensor ground 1
—
Yes
—
5AF
Power from Main Relay
—
Yes
—
5AG
NC
—
—
—
5AH
NC
—
—
—
Internal 8-pin header
Header pin
Description
Comments
1
Sensor 5V supply
—
2
Sensor Ground
—
3
MAP signal
Connected to the Air Flow Meter signal pin (pin 5N)
4
Air Temperature signal
Connected to pin 5K
5
MVSS1 (master vehicle speed sensor 1)
—
6
MVSS2 (master vehicle speed sensor 2)
—
7
SVSS1 (slave vehicle speed sensor 1)
—
8
SVSS2 (slave vehicle speed sensor 2)
—
Internal 6-pin header
Header pin
Description
Comments
1
CAS3
Can be used for flex fuel sensor input
2
Aux Temperature signal
Temperature sensors must be wired with one wire
to sensor ground and the other wire to the ECU
signal input
3
Aux Output 5
Low current, only suitable for low current loads
such as relay coils
4
Aux Output 6
Low current, only suitable for low current loads
such as relay coils
5
Digital Input 7
—
6
Digital Input 8
—
Manufacturer photograph
Adaptronic eSel002 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.Revision 4: Adaptronic eSel002
Adaptronic eSel002 is a Select-series vehicle-specific programmable interceptor ECU that works alongside the retained factory ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-8 Series 1 (2003–2008) 13B-MSP and non-MSP RENESIS. Adaptronic eSel002 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel002 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel002 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector and header tables are transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Transcribed from the Adaptronic eSel002 installation guide. This interceptor retains the factory ECU. The column headed ‘Still connected to factory ECU?’ identifies circuits that are factory-only or shared with both ECUs. The source gives numbering from the loom side, looking into the ECU. The headers are inside the ECU. In the vehicle-connector tables, “NC” is the source's designation for no factory loom connection; a blank Adaptronic entry means no connection to the Adaptronic ECU. A dash in the table reproduces a blank source field.
Factory vehicle connectors: RX-8 Series 1
Factory pin
Factory function
Adaptronic function
Still connected to factory ECU?
Comments
1A
NC
—
—
—
1B
Drive-By-Wire throttle control
—
Yes
—
1C
Drive-By-Wire throttle control
—
Yes
—
1D
SSV switch
—
Yes
—
1E
NC
—
—
—
1F
Knock sensor -
—
Yes
—
1G
Knock sensor shield
—
Yes
—
1H
NC
—
—
—
1J
Throttle position sensor 1
—
Yes
—
1K
NC
—
—
—
1L
SSV solenoid valve
Aux Output 4
No
Secondary Side Valve
1M
Throttle position sensor 2
—
Yes
—
1N
NC
—
—
—
1O
Air solenoid valve
—
Yes
—
1Q
Throttle Position Sensor power
—
Yes
—
1R
NC
—
—
—
1S
APV position sensor power
—
Yes
—
1T
Knock sensor +
Knock signal input
Yes, shared with both ECUs
—
1U
Sensor ground
Sensor Ground
Yes, shared with both ECUs
—
1V
Front O2 sensor heater
—
Yes
—
1W
VDI solenoid valve
Aux Output 3
No
Variable Dynamic Intake
1X
NC
—
—
—
2A
Rear O2 sensor heater
—
Yes
—
2B
O2 sensor ground
—
Yes
—
2C
Front O2 sensor signal
—
Yes
—
2D
Rear (Rotor 2) secondary injector
Injector Output 4
No
Secondary injectors for rotors 1 and 2 fire together
2E
Oil Pressure switch
—
Yes
—
2F
Throttle Position Sensor ground
—
Yes
—
2G
Front (Rotor 1) secondary injector
Injector Output 4
No
Secondary injectors for rotors 1 and 2 fire together
2H
Sensor shields
—
Yes
—
2I
Generator control
—
Yes
—
2J
Rear (Rotor 2) primary injector 1
Injector Output 3
No
—
2K
Engine Coolant Temperature sensor
ECT signal input
Yes, shared with both ECUs
—
2M
Front (Rotor 1) primary injector 1
Injector Output 1
No
—
2N
Oil Metering Pump switch
—
Yes
—
2O
Neutral switch
Digital Input 2
Yes, shared with both ECUs
—
2P
Purge solenoid valve
—
Yes
—
2Q
Rear O2 sensor signal
O2/EGO signal input
Yes, shared with both ECUs
—
2R
Oil Level switch
—
Yes
—
2T
Generator control
—
Yes
—
2U
Eccentric shaft position sensor +
CAS 1 input
Yes, shared with both ECUs
Reluctor trigger for ignition timing
2V
Oil Metering Pump
—
Yes
—
2W
Oil Metering Pump
—
Yes
—
2X
Eccentric shaft position sensor -
—
Yes
—
2Y
Oil Metering Pump
—
Yes
—
2Z
Rear (Rotor 2) leading ignition
Ignition output 4
No
Aux Output 1 cannot be used due to the fourth ignition output
2AA
Front (Rotor 1) leading ignition
Ignition output 1
No
—
2AB
Oil Metering Pump
—
Yes
—
2AC
Rear (Rotor 2) trailing ignition
Ignition output 3
No
—
2AD
Front (Rotor 1) trailing ignition
Ignition output 2
No
—
3A
Front (Rotor 1) primary 2 injector
Injector Output 2
No
The Adaptronic ECU fires both primary 2 injectors together
3B
APV position sensor
0-5V Ext/Spare input
Yes
—
3C
NC
—
—
—
3D
Rear (Rotor 2) primary 2 injector
Injector Output 2
No
The Adaptronic ECU fires both primary 2 injectors together
3E
NC
—
—
—
3F
NC
—
—
—
3G
APV motor control
Controlled by Aux Output 7 via additional high current circuitry inside the Adaptronic ECU
No
Auxiliary Port Valve
3H
—
—
—
—
3I
—
—
—
—
3J
APV motor control
Controlled by Aux Output 8 via additional high current circuitry inside the Adaptronic ECU
No
Auxiliary Port Valve
3K
NC
—
—
—
3M
NC
—
—
—
3N
NC
—
—
—
3O
NC
—
—
—
3P
NC
—
—
—
3Q
NC
—
—
—
3R
NC
—
—
—
4A
Ground
Power Ground
Yes, shared with both ECUs
—
4B
NC
—
—
—
4C
Power from Drive-By- Wire relay
—
Yes
—
4D
NC
—
—
—
4E
Main Relay enable
—
Yes
—
4F
Clutch switch
Digital Input 1
Yes, shared with both ECUs
—
4H
NC
—
—
—
4I
NC
—
—
—
4J
Ground
Power Ground
Yes, shared with both ECUs
—
4K
Barometric sensor power
—
Yes
—
4L
NC
—
—
—
4M
Fuel pump speed control
—
Yes
—
4N
NC
—
—
—
4O
Air pump relay
—
Yes
—
4P
Brake switch
—
Yes
—
4Q
Ignition switch
+12V Ignition
Yes, shared with both ECUs
—
4S
CAN low
—
Yes
—
4T
Coolant Level switch
—
Yes
—
4U
Sensor ground
—
Yes
—
4V
CAN high
—
Yes
—
4W
High/Low A/C control
—
Yes
—
4X
APP sensor power 2
—
Yes
—
4Y
APP sensor power 1
—
Yes
—
4Z
Medium A/C control
—
Yes
—
5A
Starter
—
Yes
—
5B
NC
—
—
—
5C
APP sensor 2
—
Yes
—
5D
Ground
Power Ground
Yes, shared with both ECUs
—
5E
NC
—
—
—
5F
APP sensor 1
Aux temp input
Yes
—
5H
Drive-By-Wire relay
—
Yes
—
5I
NC
—
—
—
5J
Constant power
—
Yes
—
5K
Intake air temperature sensor
Air Temp signal input
Yes, shared with both ECUs
—
5L
Fuel pump relay
—
Yes
—
5M
NC
—
—
—
5N
Air flow meter signal
MAP signal input
Yes, shared with both ECUs
AFM signal pin can be used for MAP signal when fitting an external MAP sensor
5O
Ground
Power Ground
Yes, shared with both ECUs
—
5P
Fuel pump relay
—
Yes
—
5R
Ground
Power Ground
Yes, shared with both ECUs
—
5S
Barometric pressure sensor
—
Yes
—
5T
Ground
Power Ground
Yes, shared with both ECUs
—
5U
Intake air temperature sensor ground
—
Yes
—
5V
Cruise control switch
—
Yes
—
5W
A/C amplifier
—
Yes
—
5X
Cooling fan relay 1
—
Yes
—
5Z
VFAD solenoid valve
Aux Output 2
No
Variable Fresh Air Duct
5AA
Aircon relay
—
Yes
—
5AB
APP sensor ground 2
—
Yes
—
5AC
Power from Main Relay
—
Yes
—
5AD
Cooling fan relays 2 and 3
—
Yes
—
5AE
APP sensor ground 1
—
Yes
—
5AF
Power from Main Relay
—
Yes
—
5AG
NC
—
—
—
5AH
NC
—
—
—
Internal 8-pin header
Header pin
Description
Comments
1
Sensor 5V supply
—
2
Sensor Ground
—
3
MAP signal
Connected to the Air Flow Meter signal pin (pin 5N)
4
Air Temperature signal
Connected to pin 5K
5
MVSS1 (master vehicle speed sensor 1)
—
6
MVSS2 (master vehicle speed sensor 2)
—
7
SVSS1 (slave vehicle speed sensor 1)
—
8
SVSS2 (slave vehicle speed sensor 2)
—
Internal 6-pin header
Header pin
Description
Comments
1
CAS3
Can be used for flex fuel sensor input
2
Aux Temperature signal
Temperature sensors must be wired with one wire
to sensor ground and the other wire to the ECU
signal input
3
Aux Output 5
Low current, only suitable for low current loads
such as relay coils
4
Aux Output 6
Low current, only suitable for low current loads
such as relay coils