Adaptronic eSel002 is a Select-series vehicle-specific programmable interceptor ECU that works alongside the retained factory ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-8 Series 1 (2003–2008) 13B-MSP and non-MSP RENESIS. Adaptronic eSel002 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel002 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel002 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector and header tables are transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Manufacturer connector schedules
Transcribed from the Adaptronic eSel002 installation guide. This interceptor retains the factory ECU. The column headed ‘Still connected to factory ECU?’ identifies circuits that are factory-only or shared with both ECUs. The source gives numbering from the loom side, looking into the ECU. The headers are inside the ECU. In the vehicle-connector tables, “NC” is the source's designation for no factory loom connection; a blank Adaptronic entry means no connection to the Adaptronic ECU. A dash in the table reproduces a blank source field.
Factory vehicle connectors: RX-8 Series 1
| Factory pin | Factory function | Adaptronic function | Still connected to factory ECU? | Comments |
|---|---|---|---|---|
| 1A | NC | — | — | — |
| 1B | Drive-By-Wire throttle control | — | Yes | — |
| 1C | Drive-By-Wire throttle control | — | Yes | — |
| 1D | SSV switch | — | Yes | — |
| 1E | NC | — | — | — |
| 1F | Knock sensor - | — | Yes | — |
| 1G | Knock sensor shield | — | Yes | — |
| 1H | NC | — | — | — |
| 1J | Throttle position sensor 1 | — | Yes | — |
| 1K | NC | — | — | — |
| 1L | SSV solenoid valve | Aux Output 4 | No | Secondary Side Valve |
| 1M | Throttle position sensor 2 | — | Yes | — |
| 1N | NC | — | — | — |
| 1O | Air solenoid valve | — | Yes | — |
| 1Q | Throttle Position Sensor power | — | Yes | — |
| 1R | NC | — | — | — |
| 1S | APV position sensor power | — | Yes | — |
| 1T | Knock sensor + | Knock signal input | Yes, shared with both ECUs | — |
| 1U | Sensor ground | Sensor Ground | Yes, shared with both ECUs | — |
| 1V | Front O2 sensor heater | — | Yes | — |
| 1W | VDI solenoid valve | Aux Output 3 | No | Variable Dynamic Intake |
| 1X | NC | — | — | — |
| 2A | Rear O2 sensor heater | — | Yes | — |
| 2B | O2 sensor ground | — | Yes | — |
| 2C | Front O2 sensor signal | — | Yes | — |
| 2D | Rear (Rotor 2) secondary injector | Injector Output 4 | No | Secondary injectors for rotors 1 and 2 fire together |
| 2E | Oil Pressure switch | — | Yes | — |
| 2F | Throttle Position Sensor ground | — | Yes | — |
| 2G | Front (Rotor 1) secondary injector | Injector Output 4 | No | Secondary injectors for rotors 1 and 2 fire together |
| 2H | Sensor shields | — | Yes | — |
| 2I | Generator control | — | Yes | — |
| 2J | Rear (Rotor 2) primary injector 1 | Injector Output 3 | No | — |
| 2K | Engine Coolant Temperature sensor | ECT signal input | Yes, shared with both ECUs | — |
| 2M | Front (Rotor 1) primary injector 1 | Injector Output 1 | No | — |
| 2N | Oil Metering Pump switch | — | Yes | — |
| 2O | Neutral switch | Digital Input 2 | Yes, shared with both ECUs | — |
| 2P | Purge solenoid valve | — | Yes | — |
| 2Q | Rear O2 sensor signal | O2/EGO signal input | Yes, shared with both ECUs | — |
| 2R | Oil Level switch | — | Yes | — |
| 2T | Generator control | — | Yes | — |
| 2U | Eccentric shaft position sensor + | CAS 1 input | Yes, shared with both ECUs | Reluctor trigger for ignition timing |
| 2V | Oil Metering Pump | — | Yes | — |
| 2W | Oil Metering Pump | — | Yes | — |
| 2X | Eccentric shaft position sensor - | — | Yes | — |
| 2Y | Oil Metering Pump | — | Yes | — |
| 2Z | Rear (Rotor 2) leading ignition | Ignition output 4 | No | Aux Output 1 cannot be used due to the fourth ignition output |
| 2AA | Front (Rotor 1) leading ignition | Ignition output 1 | No | — |
| 2AB | Oil Metering Pump | — | Yes | — |
| 2AC | Rear (Rotor 2) trailing ignition | Ignition output 3 | No | — |
| 2AD | Front (Rotor 1) trailing ignition | Ignition output 2 | No | — |
| 3A | Front (Rotor 1) primary 2 injector | Injector Output 2 | No | The Adaptronic ECU fires both primary 2 injectors together |
| 3B | APV position sensor | 0-5V Ext/Spare input | Yes | — |
| 3C | NC | — | — | — |
| 3D | Rear (Rotor 2) primary 2 injector | Injector Output 2 | No | The Adaptronic ECU fires both primary 2 injectors together |
| 3E | NC | — | — | — |
| 3F | NC | — | — | — |
| 3G | APV motor control | Controlled by Aux Output 7 via additional high current circuitry inside the Adaptronic ECU | No | Auxiliary Port Valve |
| 3H | — | — | — | — |
| 3I | — | — | — | — |
| 3J | APV motor control | Controlled by Aux Output 8 via additional high current circuitry inside the Adaptronic ECU | No | Auxiliary Port Valve |
| 3K | NC | — | — | — |
| 3M | NC | — | — | — |
| 3N | NC | — | — | — |
| 3O | NC | — | — | — |
| 3P | NC | — | — | — |
| 3Q | NC | — | — | — |
| 3R | NC | — | — | — |
| 4A | Ground | Power Ground | Yes, shared with both ECUs | — |
| 4B | NC | — | — | — |
| 4C | Power from Drive-By- Wire relay | — | Yes | — |
| 4D | NC | — | — | — |
| 4E | Main Relay enable | — | Yes | — |
| 4F | Clutch switch | Digital Input 1 | Yes, shared with both ECUs | — |
| 4H | NC | — | — | — |
| 4I | NC | — | — | — |
| 4J | Ground | Power Ground | Yes, shared with both ECUs | — |
| 4K | Barometric sensor power | — | Yes | — |
| 4L | NC | — | — | — |
| 4M | Fuel pump speed control | — | Yes | — |
| 4N | NC | — | — | — |
| 4O | Air pump relay | — | Yes | — |
| 4P | Brake switch | — | Yes | — |
| 4Q | Ignition switch | +12V Ignition | Yes, shared with both ECUs | — |
| 4S | CAN low | — | Yes | — |
| 4T | Coolant Level switch | — | Yes | — |
| 4U | Sensor ground | — | Yes | — |
| 4V | CAN high | — | Yes | — |
| 4W | High/Low A/C control | — | Yes | — |
| 4X | APP sensor power 2 | — | Yes | — |
| 4Y | APP sensor power 1 | — | Yes | — |
| 4Z | Medium A/C control | — | Yes | — |
| 5A | Starter | — | Yes | — |
| 5B | NC | — | — | — |
| 5C | APP sensor 2 | — | Yes | — |
| 5D | Ground | Power Ground | Yes, shared with both ECUs | — |
| 5E | NC | — | — | — |
| 5F | APP sensor 1 | Aux temp input | Yes | — |
| 5H | Drive-By-Wire relay | — | Yes | — |
| 5I | NC | — | — | — |
| 5J | Constant power | — | Yes | — |
| 5K | Intake air temperature sensor | Air Temp signal input | Yes, shared with both ECUs | — |
| 5L | Fuel pump relay | — | Yes | — |
| 5M | NC | — | — | — |
| 5N | Air flow meter signal | MAP signal input | Yes, shared with both ECUs | AFM signal pin can be used for MAP signal when fitting an external MAP sensor |
| 5O | Ground | Power Ground | Yes, shared with both ECUs | — |
| 5P | Fuel pump relay | — | Yes | — |
| 5R | Ground | Power Ground | Yes, shared with both ECUs | — |
| 5S | Barometric pressure sensor | — | Yes | — |
| 5T | Ground | Power Ground | Yes, shared with both ECUs | — |
| 5U | Intake air temperature sensor ground | — | Yes | — |
| 5V | Cruise control switch | — | Yes | — |
| 5W | A/C amplifier | — | Yes | — |
| 5X | Cooling fan relay 1 | — | Yes | — |
| 5Z | VFAD solenoid valve | Aux Output 2 | No | Variable Fresh Air Duct |
| 5AA | Aircon relay | — | Yes | — |
| 5AB | APP sensor ground 2 | — | Yes | — |
| 5AC | Power from Main Relay | — | Yes | — |
| 5AD | Cooling fan relays 2 and 3 | — | Yes | — |
| 5AE | APP sensor ground 1 | — | Yes | — |
| 5AF | Power from Main Relay | — | Yes | — |
| 5AG | NC | — | — | — |
| 5AH | NC | — | — | — |
Internal 8-pin header
| Header pin | Description | Comments |
|---|---|---|
| 1 | Sensor 5V supply | — |
| 2 | Sensor Ground | — |
| 3 | MAP signal | Connected to the Air Flow Meter signal pin (pin 5N) |
| 4 | Air Temperature signal | Connected to pin 5K |
| 5 | MVSS1 (master vehicle speed sensor 1) | — |
| 6 | MVSS2 (master vehicle speed sensor 2) | — |
| 7 | SVSS1 (slave vehicle speed sensor 1) | — |
| 8 | SVSS2 (slave vehicle speed sensor 2) | — |
Internal 6-pin header
| Header pin | Description | Comments |
|---|---|---|
| 1 | CAS3 | Can be used for flex fuel sensor input |
| 2 | Aux Temperature signal | Temperature sensors must be wired with one wire to sensor ground and the other wire to the ECU signal input |
| 3 | Aux Output 5 | Low current, only suitable for low current loads such as relay coils |
| 4 | Aux Output 6 | Low current, only suitable for low current loads such as relay coils |
| 5 | Digital Input 7 | — |
| 6 | Digital Input 8 | — |
Manufacturer photograph
