The Adaptronic eMod016 is an application-specific plug-in programmable engine-management ECU. Haltech's surviving Adaptronic downloads archive identifies the application as Mazda MX-5 NB8A. The part number identifies a family of applications, not an unconditional guarantee of vehicle compatibility. Haltech Adaptronic downloads archive.
Application and installation
Identify the vehicle, engine, connector and wiring variation before installation. Plug-in installation can still require additional sensor and actuator wiring, and tuning to suit the specific engine. The manufacturer archive provides the Adaptronic plug-in ECU startup guide and EUGENE tuning software.
Model-specific pinout
In the eMod016 section of the manufacturer download archive, find: NB8A_Pinout.zip. Open the matching vehicle-specific diagram; connector or pin functions cannot safely be inferred from a different eMod or a different application. The archive also lists the following basemap resource: eMod016_basemap.ecu.
MX-5 / Miata NB8A connector assignments
From Adaptronic’s eMod016 NB8A pinout archive, for 1999–2000 naturally aspirated BP engines without variable valve timing. The connector illustration is viewed looking into the ECU. Positions describe Adaptronic functions, not necessarily factory wiring; module positions depend on fitted hardware and NC means no connection per source. The source labels both 1E and 4D as check-light functions and 2A as a module position with an oil-temperature comment while 1M is also labelled oil temperature. Its 4R function says ignition output but its comment says spare input. Preserve these source inconsistencies and confirm the actual hardware before use.
| Position | Adaptronic function / notes |
|---|---|
| 1A | Alternator regulator sense (constant 12 V) |
| 1B | 12 V ignition power input |
| 1C | Fuel pressure |
| 1D | Fuel temperature |
| 1E | Ignition output 8 (check light) |
| 1F | Module 1; function depends on installed module |
| 1G | Digital input 3 (power steering load) |
| 1H | NC |
| 1I | Ignition output 6 (cooling fan relay 2) |
| 1J | TPS input 2 (spare) |
| 1K | CAN L |
| 1L | CAN H |
| 1M | Oil temperature |
| 1N | Oil pressure |
| 1O | Alternator control |
| 1P | Digital input 4 (A/C request) |
| 1Q | NC |
| 1R | Ignition output 5 (cooling fan relay 1) |
| 1S | Ignition output 7 (A/C relay) |
| 1T | NC |
| 1U | Power ground |
| 1V | Digital input 1 (neutral) |
| 2A | Module 1 (source comment says oil temperature sensor signal) |
| 2B | Module 1; function depends on installed module |
| 2C | Module 1; function depends on installed module |
| 2D | Module 1; function depends on installed module |
| 2E | Module 1; function depends on installed module |
| 2F | NC |
| 2G | Module 3; function depends on installed module |
| 2H | Module 3; function depends on installed module |
| 2I | Module 3; function depends on installed module |
| 2J | Module 3; function depends on installed module |
| 2K | Module 3; function depends on installed module |
| 2L | Module 3; function depends on installed module |
| 3A | External 0–5 V input 2 |
| 3B | Manifold air temperature |
| 3C | O2 input 1 (0–5 V) |
| 3D | VSS input |
| 3E | Engine coolant temperature |
| 3F | Knock |
| 3G | CAS 3 (flex fuel possible) |
| 3H | CAS 2 (cam sensor) |
| 3I | 5 V output |
| 3J | CAS 1 (crank sensor) |
| 3K | Tacho output |
| 3L | IMAP |
| 3M | Injector output 5 (spare) |
| 3N | Injector output 6 (spare) |
| 3O | Injector output 7 (spare) |
| 3P | Injector output 8 (spare) |
| 4A | Power ground |
| 4B | Power ground |
| 4C | Power ground |
| 4D | Ignition output 3 (check lamp in source) |
| 4E | TPS input 1 |
| 4F | Sensor ground |
| 4G | Ignition output 1 |
| 4H | Ignition output 2 |
| 4I | Digital input 2 (clutch switch) |
| 4J | O2 input 2 |
| 4K | Servo |
| 4L | Auxiliary output 4 (EGR purge valve) |
| 4M | 12 V power input |
| 4N | ECCS / fuel pump control output |
| 4O | Auxiliary output 1 (idle) |
| 4P | ECCS / fuel pump control output |
| 4Q | Auxiliary output 2 (VICS solenoid) |
| 4R | Ignition output 4 (source comment says spare input) |
| 4S | EMAP (spare input) |
| 4T | NC |
| 4U | Auxiliary output 3 (CDCV) |
| 4V | Power ground |
| 4W | Injector output 1 (cylinder 1) |
| 4X | Injector output 2 (cylinder 2) |
| 4Y | Injector output 3 (cylinder 3) |
| 4Z | Injector output 4 (cylinder 4) |
Documentation limits
Complete channel counts and additional variants have not been independently verified for this exact model. Haltech's Adaptronic notice records the end of Adaptronic operations in 2022; use the archived documentation and confirm present support before purchasing a used ECU.
Manufacturer connector diagram and ECU photograph
