Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Adaptronic standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

The Adaptronic eMod012 is an application-specific plug-in programmable engine-management ECU. Haltech's surviving Adaptronic downloads archive identifies the application as Mazda RX-7 FD Series 7 and Series 8. The part number identifies a family of applications, not an unconditional guarantee of vehicle compatibility. Haltech Adaptronic downloads archive.

Application and installation

Identify the vehicle, engine, connector and wiring variation before installation. Plug-in installation can still require additional sensor and actuator wiring, and tuning to suit the specific engine. The manufacturer archive provides the Adaptronic plug-in ECU startup guide and EUGENE tuning software.

Model-specific pinout

In the eMod012 section of the manufacturer download archive, find: RX7_S8_Pinout.zip. Open the matching vehicle-specific diagram; connector or pin functions cannot safely be inferred from a different eMod or a different application. The archive also lists the following basemap resource: eMod012_Series8_Basemap.ecu.

RX-7 Series 8 FD Twin Turbo connector assignments

From Adaptronic’s eMod012 RX7 S8 pinout archive, covering the Series 8 FD 13B REW twin-turbo application shown in that diagram. Viewed looking into the ECU; these are Adaptronic functions. Module positions depend on installed hardware; NC means no connection per source. Eleven positions shown in the connector illustration, 4AC and 4AE–4AN, are not described in its function table. The introductory turbo-control paragraph refers to 4R, 4S, 4T and 4V in a way inconsistent with this same diagram’s table; do not use those references without manufacturer confirmation. Both 3C and 4S are labelled digital input 1, and 4K/4L injector output 8. Verify actual configuration and source before wiring.

PositionAdaptronic function / notes
1AModule 2; function depends on installed module
1BModule 2; function depends on installed module
1CAuxiliary output 2 (idle)
1DInjector output 5 (port air bypass)
1EAuxiliary output 4 bar (charge control)
1FModule 1; function depends on installed module; secondary relief valve comment
1GInjector output 6 (purge solenoid)
1HIgnition output 8 (fan 1)
1IAuxiliary output 4 (charge relief)
1KAuxiliary output 1 (turbo precontrol)
1LPower ground
1MAuxiliary output 4 (twin turbo)
1OAuxiliary output 3 (wastegate control)
1QInjector output 1 (front primary)
1RModule 2; function depends on installed module
1SIgnition output 6 (oil metering pump 1)
1UInjector output 2 (rear primary)
1WIgnition output 5 (oil metering pump 2)
1XPower ground
1YInjector output 3 (front secondary)
1AAIgnition output 6 bar (oil metering pump 1 inverse)
1ABPower ground
1ACInjector output 4 (rear secondary)
1ADModule 2; function depends on installed module
1AEIgnition output 5 bar (oil metering pump 2 inverse)
1AFPower ground
1AHOil pressure input
1AJPower ground
2AModule 2; function depends on installed module
2BModule 2; function depends on installed module
2CModule 2; function depends on installed module
2DModule 2; function depends on installed module
2EModule 2; function depends on installed module
2FModule 2; function depends on installed module
2GModule 2; function depends on installed module
2HModule 2; function depends on installed module
2IModule 2; function depends on installed module
2KModule 2; function depends on installed module
2LModule 2; function depends on installed module
2MModule 2; function depends on installed module
2OModule 2; function depends on installed module
2PModule 2; function depends on installed module
2RModule 2; function depends on installed module
2TModule 2; function depends on installed module
3A5 V output
3BO2 input 2 (spare 0–5 V)
3CDigital input 1 (neutral)
3DO2 input 1 (0–5 V)
3ECAN L
3FCAN H
3GModule 1; function depends on installed module
3HServo (0–5 V, oil metering pump position)
3ITPS 1
3KTPS 2 (spare)
3MExternal 0–5 V input 1
3OKnock
3QModule 1; function depends on installed module
3RCAS 1 (12 tooth)
3SSensor ground
3TManifold air temperature
3UCAS 2 (1 tooth)
3VFuel temperature
3WEngine coolant temperature
3XOil temperature
3ZModule 1; function depends on installed module
3ABSensor ground
4A12 V power input
4BNC
4CIgnition switch input
4DNC
4ENC
4FInjector output 7 (pump speed)
4GECCS / fuel pump control output
4HNC
4IIgnition output 7 (A/C relay)
4KInjector output 8 (fan 2 and 4)
4LInjector output 8 (fan 3)
4MTacho output
4OIgnition output 2 (direct-fire L2)
4PModule 1; function depends on installed module
4QVSS
4RModule 1; function depends on installed module
4SDigital input 1 (clutch)
4UModule 3; function depends on installed module
4VDigital input 4 (A/C switch)
4WDigital input 3 (power steering)
4YCAS 3 (flex fuel)
4AAExternal exhaust MAP
4ABModule 3; function depends on installed module
4ACNot listed in source table
4AENot listed in source table
4AFNot listed in source table
4AGNot listed in source table
4AHNot listed in source table
4AINot listed in source table
4AJNot listed in source table
4AKNot listed in source table
4ALNot listed in source table
4AMNot listed in source table
4ANNot listed in source table

Documentation limits

Complete channel counts and additional variants have not been independently verified for this exact model. Haltech's Adaptronic notice records the end of Adaptronic operations in 2022; use the archived documentation and confirm present support before purchasing a used ECU.

Manufacturer connector diagram and ECU photograph

Adaptronic eMod012 manufacturer ECU and connector pinout
Adaptronic eMod012 model-specific ECU photograph and connector diagram, looking into the ECU. Source: Adaptronic / Haltech archived pinout ZIP; reproduced with permission. Consult the original installation notes and confirm the vehicle and hardware variant.