Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Adaptronic standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

The Adaptronic eMod010 is an application-specific plug-in programmable engine-management ECU. Haltech's surviving Adaptronic downloads archive identifies the application as Mazda RX-7 FC Series 5. The part number identifies a family of applications, not an unconditional guarantee of vehicle compatibility. Haltech Adaptronic downloads archive.

Application and installation

Identify the vehicle, engine, connector and wiring variation before installation. Plug-in installation can still require additional sensor and actuator wiring, and tuning to suit the specific engine. The manufacturer archive provides the Adaptronic plug-in ECU startup guide and EUGENE tuning software.

Model-specific pinout

In the eMod010 section of the manufacturer download archive, find: RX7_S5_Pinout.zip. Open the matching vehicle-specific diagram; connector or pin functions cannot safely be inferred from a different eMod or a different application. The archive also lists the following basemap resource: eMod010_RX7S5_Basemap.ecu.

RX-7 Series 5 FC Turbo connector assignments

From Adaptronic’s eMod010 RX7 S5 pinout archive, for the RX-7 FC Series 5 13B turbo. Connector drawing is viewed looking into the ECU; these are Adaptronic functions, not necessarily factory functions. Module positions depend on the installed board. NC is no connection per source. The manufacturer lists both 1Q and 1R as digital input 1; verify against the actual ECU and manufacturer rather than assuming they are separate channels. “Bar” is retained from the manufacturer output names. Confirm connector, vehicle configuration and source diagram before wiring.

PositionAdaptronic function / notes
1ANC
1B12 V power input from ignition
1CModule 1; function depends on installed module
1DCAS 3 (flex-fuel input)
1EAuxiliary output 4 (check light)
1FFuel pressure
1GIgnition output 3 (trailing / trailing 1 direct fire)
1HIgnition output 1 (leading / leading 1 direct fire)
1IIgnition output 2 (direct-fire L2)
1JIgnition output 4 (trailing select / trailing 2 direct fire)
1KIgnition output 8 (fuel pump speed)
1LIgnition output 7 (A/C output)
1MVSS
1NDigital input 3 (power steering)
1ODigital input 4 (A/C request)
1PModule 1; function depends on installed module
1QDigital input 1 (clutch switch)
1RDigital input 1 (neutral switch)
1SOil pressure
1TModule 1; function depends on installed module
1UFuel temperature
1VOil temperature
2AModule 1; function depends on installed module
2BModule 1; function depends on installed module
2CModule 1; function depends on installed module
2DNC
2EModule 3; function depends on installed module
2FNC
2GModule 3; function depends on installed module
2HModule 3; function depends on installed module
2IModule 3; function depends on installed module
2JModule 3; function depends on installed module
2KModule 3; function depends on installed module
2LNC
3AServo / oil-metering pump position input (0–5 V)
3BSensor ground
3CO2 input 1 (0–5 V)
3DO2 input 2 (spare 0–5 V)
3EEngine coolant temperature
3FTPS 2 (spare input)
3GTPS 1
3HExternal intake MAP
3ITPS 5 V
3JPower ground
3KExternal exhaust MAP
3LManifold air temperature
3MKnock
3NInjector output 7 (port air bypass)
3OAuxiliary output 1 (switch solenoid)
3PInjector output 8 (relief solenoid)
4APower ground
4BPower ground
4CPower ground
4DSensor ground
4ECAS 1 (NE 24-tooth)
4FTacho (available for direct-fire conversion)
4GCAS 2 (G 2-tooth)
4HSensor ground
4IInjector output 5 (split-air solenoid)
4JInjector output 6 (AWS solenoid)
4KECCS (fuel pump or EFI relay)
4LDigital input 2 (headlights)
4MExternal 0–5 V input 1
4NExternal 0–5 V input 2
4OCAN L
4PCAN H
4QAuxiliary output 2 (idle air)
4RAuxiliary output 3 (boost control)
4SIgnition output 6 (oil-metering pump 2)
4TIgnition output 5 (oil-metering pump 1)
4UIgnition output 6 bar (oil-metering pump 2 bar)
4VIgnition output 5 bar (oil-metering pump 1 bar)
4WInjector output 1 (front primary)
4XInjector output 3 (front secondary)
4YInjector output 2 (rear primary)
4ZInjector output 4 (rear secondary)

Documentation limits

Complete channel counts and additional variants have not been independently verified for this exact model. Haltech's Adaptronic notice records the end of Adaptronic operations in 2022; use the archived documentation and confirm present support before purchasing a used ECU.

Manufacturer connector diagram and ECU photograph

Adaptronic eMod010 manufacturer ECU and connector pinout
Adaptronic eMod010 model-specific ECU photograph and connector diagram, looking into the ECU. Source: Adaptronic / Haltech archived pinout ZIP; reproduced with permission. Consult the original installation notes and confirm the vehicle and hardware variant.