Audi's 0GC is a seven-speed transverse DQ381 transmission; its 0DL is a seven-speed DQ500 application. Audi's A3 powertrain training identifies 0GC as DQ381, and its Q3 training identifies 0DL as DQ500-7A. They are different gearbox families even though some diagnostic bulletins discuss both. Identify the vehicle, transmission, mechatronic assembly, TCM hardware and software; a component part number beginning 0GC does not by itself prove that the complete gearbox is a DQ381.
Clutch position-sensor electrical faults
Audi's historical North American TSB 35 20 37 / 2058504/1 covers listed 2017–2020 A3, A3 Cabriolet, S3, RS3 and TT RS, and listed 2019–2020 TTS and TT Roadster vehicles with 0GC/0DL. It describes shudder, a gearbox warning or a restricted odd- or even-gear mode together with P173500 and symptom code 10666 for clutch-position sensor 1 and/or P173600 and symptom code 10668 for sensor 2. Audi described a mechatronic hardware issue for the documented combination. The code and symptom suffix, actual model and gearbox all matter; the same warning or a base code alone does not establish this fault.
Audi's separate TSB 35 23 44 / 2070217/1 covers specified later model ranges and lists additional clutch, selector, input-speed and control-module fault combinations for 0GC/0DL. Its historical service path first requires the TCM software part number and software version to match its table, then differentiates the mechatronic index and control-unit parts. An 0DL gearbox can have a mechatronic unit with an 0GC index in that bulletin. Neither the code family nor the prefix alone is a replacement-parts verdict. Audi's 2020 and 2023 service procedures are distinct historical instructions; consult the latest vehicle-specific guided test and repair information before choosing a path.
Revision to the fault list: Audi later issued TSB 35 24 52 / 2070217/3, July 2024, superseding the May 2024 revision of 2070217. Its revision history states that the workshop fault list was updated: the shown 0GC/0DL entries are P173500 with symptom 10666 and P173600 with symptom 10668. The broader 2023 list above is retained as historical context and must not be treated as the applicability list for the 2024 revision. The newer note still requires matching the listed software part number and version. Verify the latest Audi guided procedure and the complete vehicle and fault information before applying any historical bulletin.
Clutch-wear pattern: 0GC example
For listed 2017–2020 A3 and A3 Cabriolet, 2018–2020 S3 and 2019–2020 TT-family 0GC vehicles, Audi TSB 30 20 29 / 2060560/1 describes possible take-up slip, a gearbox warning or shudder on shifts into odd-numbered gears. Its specific workshop findings combine a very high calculated maximum K1 temperature, dark burnt-smelling transmission fluid and relevant faults; it first directs a check of another applicable bulletin. Audi identifies K1 wear in that documented case. An odd-gear symptom, dark fluid or a calculated temperature alone is not proof of a worn clutch. Check all specified conditions and current guided diagnosis; the stored calculated value is not an independent direct temperature measurement.
Diagnostic and service boundaries
- Record the VIN, gearbox designation, TCM software number and version, previous programming or component work, symptoms, gear, temperature and complete DTCs with their manufacturer symptom codes before clearing or adapting.
- Use the vehicle-specific guided test to compare requested and actual gear, clutch and shaft speeds, pressure and temperature data where supported, supply and electrical communication. An odd/even pattern helps organise evidence but can reflect different sensor, hydraulic, mechanical or control causes.
- Follow current manufacturer procedures for fluid identification and level, mechatronic repairs, programming and basic settings. Identical fault-code labels do not establish identical fluid, hardware or repair strategy for 0GC and 0DL. A reset or adaptation cannot fix a hardware defect or a worn clutch.
See DQ500 identification and shift selection, DQ250 diagnosis and the electronic gearbox index.