Page organisation in this revision
- Page type
- Reference hub
- Subject
- ABS / DSC
- Parent
- RaceTCS traction control systems
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- RaceTCS
Changes from revision 3 to revision 4
Removed text is struck through; added text is highlighted.
ABS and traction systems · RaceTCS · Motorsport overview
RaceTCS V2 is a standalone traction controller that compares driven and reference wheel speeds and reduces engine output by cutting complete fuel-injector pulses. It does not modulate hydraulic brakes and is not ABS. RaceTCS V2 user manual, pp. 3–4.
Functions and applicability
The cited V2 manual lists a target-slip limiter and RPM limits, including configured launch and flat-shift functions. It describes sequential or batch/bank petrol injection subject to its stated electrical limits, and explicitly says fuel cut is not supported for direct-injection engines. It also specifies injector impedance and excludes PWM-controlled injectors; use the exact manual and supplier to establish compatibility. V2 manual, requirements.
Wheel-speed sensing and engine-output wiring must be checked for the particular vehicle. The manufacturer identifies V2 as motorsport equipment and warns that incorrect installation can damage components; verify class rules and commissioning procedures.
Documented vehicle examples
The manufacturer provides example installation schematics for Nissan 350Z and 300ZX, Opel Speedster/VX220 turbo, BMW E36 and E46, Mazda RX-8 and MX-5 NC (pre-facelift and 2012 onward), and fifth-generation Ford Mustang GT. These are aftermarket installation guides, not factory fitments; check the engine, ECU, connector and diagram for the specific car. Manufacturer manual: car-specific schematics.
Connector pinout
RaceTCS V2 connector pinout — model-specific manufacturer wiring reference.
V2 electrical and activation requirementsThe 2024-05-13 V2 manual specifies high-impedance fuel injectors of at least 10 ohms and excludes PWM-controlled injectors. It says a clutch-switch input is mandatory when the configured launch or flat-shift functions are required. Wheel-slip limiting operates above the configured activation speed and RPM, while launch and flat shift use separately configured RPM limits. These are requirements and behaviour from that manual, not proof of compatibility with an unverified engine or wiring configuration. Source: RaceTCS V2 user manual, pages 3–4 and 7.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: RaceTCS V2
ABS and traction systems · RaceTCS · Motorsport overview
RaceTCS V2 is a standalone traction controller that compares driven and reference wheel speeds and reduces engine output by cutting complete fuel-injector pulses. It does not modulate hydraulic brakes and is not ABS. RaceTCS V2 user manual, pp. 3–4.
Functions and applicability
The cited V2 manual lists a target-slip limiter and RPM limits, including configured launch and flat-shift functions. It describes sequential or batch/bank petrol injection subject to its stated electrical limits, and explicitly says fuel cut is not supported for direct-injection engines. It also specifies injector impedance and excludes PWM-controlled injectors; use the exact manual and supplier to establish compatibility. V2 manual, requirements.
Wheel-speed sensing and engine-output wiring must be checked for the particular vehicle. The manufacturer identifies V2 as motorsport equipment and warns that incorrect installation can damage components; verify class rules and commissioning procedures.
Documented vehicle examples
The manufacturer provides example installation schematics for Nissan 350Z and 300ZX, Opel Speedster/VX220 turbo, BMW E36 and E46, Mazda RX-8 and MX-5 NC (pre-facelift and 2012 onward), and fifth-generation Ford Mustang GT. These are aftermarket installation guides, not factory fitments; check the engine, ECU, connector and diagram for the specific car. Manufacturer manual: car-specific schematics.
Connector pinout
RaceTCS V2 connector pinout — model-specific manufacturer wiring reference.
Revision 4: RaceTCS V2
ABS and traction systems · RaceTCS · Motorsport overview
RaceTCS V2 is a standalone traction controller that compares driven and reference wheel speeds and reduces engine output by cutting complete fuel-injector pulses. It does not modulate hydraulic brakes and is not ABS. RaceTCS V2 user manual, pp. 3–4.
Functions and applicability
The cited V2 manual lists a target-slip limiter and RPM limits, including configured launch and flat-shift functions. It describes sequential or batch/bank petrol injection subject to its stated electrical limits, and explicitly says fuel cut is not supported for direct-injection engines. It also specifies injector impedance and excludes PWM-controlled injectors; use the exact manual and supplier to establish compatibility. V2 manual, requirements.
Wheel-speed sensing and engine-output wiring must be checked for the particular vehicle. The manufacturer identifies V2 as motorsport equipment and warns that incorrect installation can damage components; verify class rules and commissioning procedures.
Documented vehicle examples
The manufacturer provides example installation schematics for Nissan 350Z and 300ZX, Opel Speedster/VX220 turbo, BMW E36 and E46, Mazda RX-8 and MX-5 NC (pre-facelift and 2012 onward), and fifth-generation Ford Mustang GT. These are aftermarket installation guides, not factory fitments; check the engine, ECU, connector and diagram for the specific car. Manufacturer manual: car-specific schematics.
Connector pinout
RaceTCS V2 connector pinout — model-specific manufacturer wiring reference.
V2 electrical and activation requirements
The 2024-05-13 V2 manual specifies high-impedance fuel injectors of at least 10 ohms and excludes PWM-controlled injectors. It says a clutch-switch input is mandatory when the configured launch or flat-shift functions are required. Wheel-slip limiting operates above the configured activation speed and RPM, while launch and flat shift use separately configured RPM limits. These are requirements and behaviour from that manual, not proof of compatibility with an unverified engine or wiring configuration. Source: RaceTCS V2 user manual, pages 3–4 and 7.