Page organisation in this revision
- Page type
- Technical article
- Subject
- ABS / DSC
- Parent
- SCS Delta Motorsport ABS
- Applies to
- SCS Delta Motorsport ABS
- Tool groups
- None
- Manufacturers
- SCS Delta
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
ABS and traction systems · SCS Delta Motorsport ABS
Scope and identification
The Delta ABS technical data sheet labels the 38-pin 1928405167 connector allocation as SCS Delta ABS Gen 2 Rev. 3. The separate auxiliary DTM06-12S table is for the second-generation kit wiring loom described in the manual; its table does not separately identify Rev. 3. Confirm the exact module, loom, connector numbering and mating-face orientation with the manufacturer before wiring. Do not generalise these allocations to other Delta generations or ECU models. The system is intended for motorsport and is not approved for public-highway use. Delta ABS technical data sheet; Delta ABS user manual.
Main ABS unit: 38-pin 1928405167
Numbers follow the allocation document; confirm the mating-face orientation. Public and private CAN are distinct. Front, rear, left and right refer to the vehicle. Source: Delta ABS technical data sheet, ABS main unit pin-out.
PinDocumented function1Pump battery supply; 40 A fuse2Front-right wheel-speed output; 0.75 A open collector3ABS active output; 0.75 A open collector4Front-right wheel-speed sensor ground55 V reference for slip potentiometer; 200 mA maximum65 V reference for pressure sensors; 200 mA maximum7Slip-potentiometer sensor ground8Front-left wheel-speed sensor ground9Sensor ground10ABS warning-lamp output; 0.75 A open collector11Speedometer output; 0.75 A open collector12Rear-right wheel-speed output; 0.75 A open collector13Solenoid and wheel-speed sensor battery supply; 20 A fuse14Public CAN 2 low15Brake-light output; 0.5 A maximum open collector16Rear-left wheel-speed output; 0.75 A open collector17Front-left wheel-speed output; 0.75 A open collector18Rear-left wheel-speed sensor ground19Front-left wheel-speed sensor input; 14/7 mA Hall effect20Private CAN 1 low21Spare analogue input LF22Slip-potentiometer signal; 0–5 V23Analogue sensor ground24Spare analogue input RF25Pump ground; direct to battery negative26Public CAN 2 high27Spare analogue input RR28Ignition wake-up supply; 10 A fuse29Rear-right wheel-speed sensor ground30Spare analogue input LR31Rear-left wheel-speed sensor input; 14/7 mA Hall effect32Rear-right wheel-speed sensor input; 14/7 mA Hall effect33Private CAN 1 high34Front-right wheel-speed sensor input; 14/7 mA Hall effect35Off switch input; system active when switched to ground36Front brake-pressure input37Rear brake-pressure input38Power ground; direct to battery negative
Auxiliary loom connector: 12-pin DTM06-12S
This is the separate auxiliary connector, not the main HCU connector. The CAN pair is the public CAN bus. Wire colours below describe the supplied loom documented in the user manual. Source: Delta ABS user manual, Technical Information.
PinWire colourDocumented function1BlackGround2Yellow/blackCAN low; termination resistor not fitted3Black/yellowCAN high; termination resistor not fitted4Brown/redABS active output; 0.75 A open collector5Brown/yellowBrake-light output; 0.5 A maximum open collector; 2 bar on / 1 bar off6Green/purpleSpeedometer output; 0.75 A open collector7Orange/pinkFront-left wheel-speed output; 0.75 A open collector8Orange/blueFront-right wheel-speed output; 0.75 A open collector9Orange/redRear-left wheel-speed output; 0.75 A open collector10Orange/greenRear-right wheel-speed output; 0.75 A open collector11EmptyNot used12White/redIgnition-switched 12 V output for external devices; 5 A maximum; not ABS power input
Auxiliary pin 12 supplies switched power to external devices; the manual says it must not be used as the ABS system power input. Follow the current manufacturer installation guide for fusing, sensor compatibility, installation and commissioning.
Sources
Delta ABS technical data sheet: Gen 2 Rev. 3 main connector allocationDelta ABS user manual: second-generation unit and auxiliary connectorDelta ABS USA FAQ linking to the documentationSCS Delta Motorsport ABS product page
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: SCS Delta Motorsport ABS Gen 2 Rev 3 connector pinouts
ABS and traction systems · SCS Delta Motorsport ABS
Scope and identification
The Delta ABS technical data sheet labels the 38-pin 1928405167 connector allocation as SCS Delta ABS Gen 2 Rev. 3. The separate auxiliary DTM06-12S table is for the second-generation kit wiring loom described in the manual; its table does not separately identify Rev. 3. Confirm the exact module, loom, connector numbering and mating-face orientation with the manufacturer before wiring. Do not generalise these allocations to other Delta generations or ECU models. The system is intended for motorsport and is not approved for public-highway use. Delta ABS technical data sheet; Delta ABS user manual.
Main ABS unit: 38-pin 1928405167
Numbers follow the allocation document; confirm the mating-face orientation. Public and private CAN are distinct. Front, rear, left and right refer to the vehicle. Source: Delta ABS technical data sheet, ABS main unit pin-out.
| Pin | Documented function |
|---|
| 1 | Pump battery supply; 40 A fuse |
| 2 | Front-right wheel-speed output; 0.75 A open collector |
| 3 | ABS active output; 0.75 A open collector |
| 4 | Front-right wheel-speed sensor ground |
| 5 | 5 V reference for slip potentiometer; 200 mA maximum |
| 6 | 5 V reference for pressure sensors; 200 mA maximum |
| 7 | Slip-potentiometer sensor ground |
| 8 | Front-left wheel-speed sensor ground |
| 9 | Sensor ground |
| 10 | ABS warning-lamp output; 0.75 A open collector |
| 11 | Speedometer output; 0.75 A open collector |
| 12 | Rear-right wheel-speed output; 0.75 A open collector |
| 13 | Solenoid and wheel-speed sensor battery supply; 20 A fuse |
| 14 | Public CAN 2 low |
| 15 | Brake-light output; 0.5 A maximum open collector |
| 16 | Rear-left wheel-speed output; 0.75 A open collector |
| 17 | Front-left wheel-speed output; 0.75 A open collector |
| 18 | Rear-left wheel-speed sensor ground |
| 19 | Front-left wheel-speed sensor input; 14/7 mA Hall effect |
| 20 | Private CAN 1 low |
| 21 | Spare analogue input LF |
| 22 | Slip-potentiometer signal; 0–5 V |
| 23 | Analogue sensor ground |
| 24 | Spare analogue input RF |
| 25 | Pump ground; direct to battery negative |
| 26 | Public CAN 2 high |
| 27 | Spare analogue input RR |
| 28 | Ignition wake-up supply; 10 A fuse |
| 29 | Rear-right wheel-speed sensor ground |
| 30 | Spare analogue input LR |
| 31 | Rear-left wheel-speed sensor input; 14/7 mA Hall effect |
| 32 | Rear-right wheel-speed sensor input; 14/7 mA Hall effect |
| 33 | Private CAN 1 high |
| 34 | Front-right wheel-speed sensor input; 14/7 mA Hall effect |
| 35 | Off switch input; system active when switched to ground |
| 36 | Front brake-pressure input |
| 37 | Rear brake-pressure input |
| 38 | Power ground; direct to battery negative |
Auxiliary loom connector: 12-pin DTM06-12S
This is the separate auxiliary connector, not the main HCU connector. The CAN pair is the public CAN bus. Wire colours below describe the supplied loom documented in the user manual. Source: Delta ABS user manual, Technical Information.
| Pin | Wire colour | Documented function |
|---|
| 1 | Black | Ground |
| 2 | Yellow/black | CAN low; termination resistor not fitted |
| 3 | Black/yellow | CAN high; termination resistor not fitted |
| 4 | Brown/red | ABS active output; 0.75 A open collector |
| 5 | Brown/yellow | Brake-light output; 0.5 A maximum open collector; 2 bar on / 1 bar off |
| 6 | Green/purple | Speedometer output; 0.75 A open collector |
| 7 | Orange/pink | Front-left wheel-speed output; 0.75 A open collector |
| 8 | Orange/blue | Front-right wheel-speed output; 0.75 A open collector |
| 9 | Orange/red | Rear-left wheel-speed output; 0.75 A open collector |
| 10 | Orange/green | Rear-right wheel-speed output; 0.75 A open collector |
| 11 | Empty | Not used |
| 12 | White/red | Ignition-switched 12 V output for external devices; 5 A maximum; not ABS power input |
Auxiliary pin 12 supplies switched power to external devices; the manual says it must not be used as the ABS system power input. Follow the current manufacturer installation guide for fusing, sensor compatibility, installation and commissioning.
Sources
Revision 1: SCS Delta Motorsport ABS Gen 2 Rev 3 connector pinouts
ABS and traction systems · SCS Delta Motorsport ABS
Scope and identification
The Delta ABS technical data sheet labels the 38-pin 1928405167 connector allocation as SCS Delta ABS Gen 2 Rev. 3. The separate auxiliary DTM06-12S table is for the second-generation kit wiring loom described in the manual; its table does not separately identify Rev. 3. Confirm the exact module, loom, connector numbering and mating-face orientation with the manufacturer before wiring. Do not generalise these allocations to other Delta generations or ECU models. The system is intended for motorsport and is not approved for public-highway use. Delta ABS technical data sheet; Delta ABS user manual.
Main ABS unit: 38-pin 1928405167
Numbers follow the allocation document; confirm the mating-face orientation. Public and private CAN are distinct. Front, rear, left and right refer to the vehicle. Source: Delta ABS technical data sheet, ABS main unit pin-out.
| Pin | Documented function |
|---|
| 1 | Pump battery supply; 40 A fuse |
| 2 | Front-right wheel-speed output; 0.75 A open collector |
| 3 | ABS active output; 0.75 A open collector |
| 4 | Front-right wheel-speed sensor ground |
| 5 | 5 V reference for slip potentiometer; 200 mA maximum |
| 6 | 5 V reference for pressure sensors; 200 mA maximum |
| 7 | Slip-potentiometer sensor ground |
| 8 | Front-left wheel-speed sensor ground |
| 9 | Sensor ground |
| 10 | ABS warning-lamp output; 0.75 A open collector |
| 11 | Speedometer output; 0.75 A open collector |
| 12 | Rear-right wheel-speed output; 0.75 A open collector |
| 13 | Solenoid and wheel-speed sensor battery supply; 20 A fuse |
| 14 | Public CAN 2 low |
| 15 | Brake-light output; 0.5 A maximum open collector |
| 16 | Rear-left wheel-speed output; 0.75 A open collector |
| 17 | Front-left wheel-speed output; 0.75 A open collector |
| 18 | Rear-left wheel-speed sensor ground |
| 19 | Front-left wheel-speed sensor input; 14/7 mA Hall effect |
| 20 | Private CAN 1 low |
| 21 | Spare analogue input LF |
| 22 | Slip-potentiometer signal; 0–5 V |
| 23 | Analogue sensor ground |
| 24 | Spare analogue input RF |
| 25 | Pump ground; direct to battery negative |
| 26 | Public CAN 2 high |
| 27 | Spare analogue input RR |
| 28 | Ignition wake-up supply; 10 A fuse |
| 29 | Rear-right wheel-speed sensor ground |
| 30 | Spare analogue input LR |
| 31 | Rear-left wheel-speed sensor input; 14/7 mA Hall effect |
| 32 | Rear-right wheel-speed sensor input; 14/7 mA Hall effect |
| 33 | Private CAN 1 high |
| 34 | Front-right wheel-speed sensor input; 14/7 mA Hall effect |
| 35 | Off switch input; system active when switched to ground |
| 36 | Front brake-pressure input |
| 37 | Rear brake-pressure input |
| 38 | Power ground; direct to battery negative |
Auxiliary loom connector: 12-pin DTM06-12S
This is the separate auxiliary connector, not the main HCU connector. The CAN pair is the public CAN bus. Wire colours below describe the supplied loom documented in the user manual. Source: Delta ABS user manual, Technical Information.
| Pin | Wire colour | Documented function |
|---|
| 1 | Black | Ground |
| 2 | Yellow/black | CAN low; termination resistor not fitted |
| 3 | Black/yellow | CAN high; termination resistor not fitted |
| 4 | Brown/red | ABS active output; 0.75 A open collector |
| 5 | Brown/yellow | Brake-light output; 0.5 A maximum open collector; 2 bar on / 1 bar off |
| 6 | Green/purple | Speedometer output; 0.75 A open collector |
| 7 | Orange/pink | Front-left wheel-speed output; 0.75 A open collector |
| 8 | Orange/blue | Front-right wheel-speed output; 0.75 A open collector |
| 9 | Orange/red | Rear-left wheel-speed output; 0.75 A open collector |
| 10 | Orange/green | Rear-right wheel-speed output; 0.75 A open collector |
| 11 | Empty | Not used |
| 12 | White/red | Ignition-switched 12 V output for external devices; 5 A maximum; not ABS power input |
Auxiliary pin 12 supplies switched power to external devices; the manual says it must not be used as the ABS system power input. Follow the current manufacturer installation guide for fusing, sensor compatibility, installation and commissioning.
Sources