Page organisation in this revision
- Page type
- Technical article
- Subject
- ABS / DSC
- Parent
- Racelogic Traction Control
- Applies to
- Racelogic Traction Control
- Tool groups
- None
- Manufacturers
- Racelogic
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
Racelogic Traction Control · Racelogic systems
This connector reference is for the separate legacy Racelogic Traction Control system described in the manufacturer's Traction Control Manual v3.2, section 1.13, printed page 28; v3.2 identifies the manual revision, not a hardware generation. Confirm the box, loom and variant against the source before wiring. The system controls traction using engine intervention; it is not a hydraulic ABS controller.
Connector A
Pin numbering, designations and colours follow the manufacturer's table. A dash means the table does not specify a colour; N/C is printed as such.
PinManual designationManual wire colour1GNDBlack2VIGNRed3POTGreen4WSPA1Red5WSPA2Blue6WSPA3Yellow7WSPA4Green8I/P 1Red9I/P 2Orange10I/P 3Yellow11O/P 1Red/Black12O/P 2Orange/Black13O/P 3Yellow/Black14GNDBlack155VRed16GNDBlue17ON/OFFN/C18RPMWhite/Black19GNDYellow/Green20CSWITCH—21I/P 6Pink22I/P 5Grey23I/P 4Green24O/P 4Green/Black25O/P 5Grey/Black26O/P 6Pink/Black
Connector B
PinManual designationManual wire colour1I/P 7White/Red*2I/P 8Orange/Red*3GND—4CONT1—5DIAG TXBlue6DIAG RXRed7GNDGreen8O/P 7Green/Red*9O/P 8Grey/Blue*10GND—11CSWITCH*—12CONT3—13CONT2—14GSHIFTBlue1512VRed1612V—
* The manufacturer marks these entries as TC8 only. The manual's pinout does not provide colours for the cells shown as a dash. CONT, GSHIFT and other unexplained labels are retained as printed instead of assigning assumed functions.
Injector and wheel-speed connections
I/P is the input from the engine ECU side of an injector signal; its matching O/P returns to the injector side. Manual page 27 pairs A8→A11, A9→A12, A10→A13, A23→A24, A22→A25, A21→A26, and for TC8 B1→B8 and B2→B9. The four- and six-cylinder versions do not use all eight channels. Racelogic manual.
WSPA1–4 are wheel-speed channels, not fixed vehicle corners. Assign and calibrate their positions, tyre sizes and pulses per revolution for the installation. Racelogic specifies saturated injector signals, and warns against peak-and-hold or PWM injector drive and injectors under 4 ohms; confirm the actual ECU and injectors before installation. Manufacturer fitting instructions; calibration instructions.
A20 CSWITCH must not be connected to a 12 V clutch feed; Racelogic calls for an independent switch between this input and ground. The manufacturer warns that applying 12 V causes hardware damage. Racelogic full-throttle shift instructions.
Documented installation examples
Racelogic's fitting guide shows its launch button and manual slip adjuster installed in a Nissan 300ZX and a manual slip adjuster in a Holden HSV. These are examples of aftermarket installations, not evidence of factory fitment or compatibility across every engine and variant. The manual also discusses Nissan 200SX installations with a single differential-mounted rear speed sensor: automatic calibration is unavailable in that configuration and software setup is required. Racelogic fitting examples; manual, section 1.11, printed pages 25–26.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Racelogic traction control connector A and B pinout
Racelogic Traction Control · Racelogic systems
This connector reference is for the separate legacy Racelogic Traction Control system described in the manufacturer's Traction Control Manual v3.2, section 1.13, printed page 28; v3.2 identifies the manual revision, not a hardware generation. Confirm the box, loom and variant against the source before wiring. The system controls traction using engine intervention; it is not a hydraulic ABS controller.
Connector A
Pin numbering, designations and colours follow the manufacturer's table. A dash means the table does not specify a colour; N/C is printed as such.
| Pin | Manual designation | Manual wire colour |
|---|
| 1 | GND | Black |
| 2 | VIGN | Red |
| 3 | POT | Green |
| 4 | WSPA1 | Red |
| 5 | WSPA2 | Blue |
| 6 | WSPA3 | Yellow |
| 7 | WSPA4 | Green |
| 8 | I/P 1 | Red |
| 9 | I/P 2 | Orange |
| 10 | I/P 3 | Yellow |
| 11 | O/P 1 | Red/Black |
| 12 | O/P 2 | Orange/Black |
| 13 | O/P 3 | Yellow/Black |
| 14 | GND | Black |
| 15 | 5V | Red |
| 16 | GND | Blue |
| 17 | ON/OFF | N/C |
| 18 | RPM | White/Black |
| 19 | GND | Yellow/Green |
| 20 | CSWITCH | — |
| 21 | I/P 6 | Pink |
| 22 | I/P 5 | Grey |
| 23 | I/P 4 | Green |
| 24 | O/P 4 | Green/Black |
| 25 | O/P 5 | Grey/Black |
| 26 | O/P 6 | Pink/Black |
Connector B
| Pin | Manual designation | Manual wire colour |
|---|
| 1 | I/P 7 | White/Red* |
| 2 | I/P 8 | Orange/Red* |
| 3 | GND | — |
| 4 | CONT1 | — |
| 5 | DIAG TX | Blue |
| 6 | DIAG RX | Red |
| 7 | GND | Green |
| 8 | O/P 7 | Green/Red* |
| 9 | O/P 8 | Grey/Blue* |
| 10 | GND | — |
| 11 | CSWITCH* | — |
| 12 | CONT3 | — |
| 13 | CONT2 | — |
| 14 | GSHIFT | Blue |
| 15 | 12V | Red |
| 16 | 12V | — |
* The manufacturer marks these entries as TC8 only. The manual's pinout does not provide colours for the cells shown as a dash. CONT, GSHIFT and other unexplained labels are retained as printed instead of assigning assumed functions.
Injector and wheel-speed connections
I/P is the input from the engine ECU side of an injector signal; its matching O/P returns to the injector side. Manual page 27 pairs A8→A11, A9→A12, A10→A13, A23→A24, A22→A25, A21→A26, and for TC8 B1→B8 and B2→B9. The four- and six-cylinder versions do not use all eight channels. Racelogic manual.
WSPA1–4 are wheel-speed channels, not fixed vehicle corners. Assign and calibrate their positions, tyre sizes and pulses per revolution for the installation. Racelogic specifies saturated injector signals, and warns against peak-and-hold or PWM injector drive and injectors under 4 ohms; confirm the actual ECU and injectors before installation. Manufacturer fitting instructions; calibration instructions.
A20 CSWITCH must not be connected to a 12 V clutch feed; Racelogic calls for an independent switch between this input and ground. The manufacturer warns that applying 12 V causes hardware damage. Racelogic full-throttle shift instructions.
Documented installation examples
Racelogic's fitting guide shows its launch button and manual slip adjuster installed in a Nissan 300ZX and a manual slip adjuster in a Holden HSV. These are examples of aftermarket installations, not evidence of factory fitment or compatibility across every engine and variant. The manual also discusses Nissan 200SX installations with a single differential-mounted rear speed sensor: automatic calibration is unavailable in that configuration and software setup is required. Racelogic fitting examples; manual, section 1.11, printed pages 25–26.
Revision 1: Racelogic traction control connector A and B pinout
Racelogic Traction Control · Racelogic systems
This connector reference is for the separate legacy Racelogic Traction Control system described in the manufacturer's Traction Control Manual v3.2, section 1.13, printed page 28; v3.2 identifies the manual revision, not a hardware generation. Confirm the box, loom and variant against the source before wiring. The system controls traction using engine intervention; it is not a hydraulic ABS controller.
Connector A
Pin numbering, designations and colours follow the manufacturer's table. A dash means the table does not specify a colour; N/C is printed as such.
| Pin | Manual designation | Manual wire colour |
|---|
| 1 | GND | Black |
| 2 | VIGN | Red |
| 3 | POT | Green |
| 4 | WSPA1 | Red |
| 5 | WSPA2 | Blue |
| 6 | WSPA3 | Yellow |
| 7 | WSPA4 | Green |
| 8 | I/P 1 | Red |
| 9 | I/P 2 | Orange |
| 10 | I/P 3 | Yellow |
| 11 | O/P 1 | Red/Black |
| 12 | O/P 2 | Orange/Black |
| 13 | O/P 3 | Yellow/Black |
| 14 | GND | Black |
| 15 | 5V | Red |
| 16 | GND | Blue |
| 17 | ON/OFF | N/C |
| 18 | RPM | White/Black |
| 19 | GND | Yellow/Green |
| 20 | CSWITCH | — |
| 21 | I/P 6 | Pink |
| 22 | I/P 5 | Grey |
| 23 | I/P 4 | Green |
| 24 | O/P 4 | Green/Black |
| 25 | O/P 5 | Grey/Black |
| 26 | O/P 6 | Pink/Black |
Connector B
| Pin | Manual designation | Manual wire colour |
|---|
| 1 | I/P 7 | White/Red* |
| 2 | I/P 8 | Orange/Red* |
| 3 | GND | — |
| 4 | CONT1 | — |
| 5 | DIAG TX | Blue |
| 6 | DIAG RX | Red |
| 7 | GND | Green |
| 8 | O/P 7 | Green/Red* |
| 9 | O/P 8 | Grey/Blue* |
| 10 | GND | — |
| 11 | CSWITCH* | — |
| 12 | CONT3 | — |
| 13 | CONT2 | — |
| 14 | GSHIFT | Blue |
| 15 | 12V | Red |
| 16 | 12V | — |
* The manufacturer marks these entries as TC8 only. The manual's pinout does not provide colours for the cells shown as a dash. CONT, GSHIFT and other unexplained labels are retained as printed instead of assigning assumed functions.
Injector and wheel-speed connections
I/P is the input from the engine ECU side of an injector signal; its matching O/P returns to the injector side. Manual page 27 pairs A8→A11, A9→A12, A10→A13, A23→A24, A22→A25, A21→A26, and for TC8 B1→B8 and B2→B9. The four- and six-cylinder versions do not use all eight channels. Racelogic manual.
WSPA1–4 are wheel-speed channels, not fixed vehicle corners. Assign and calibrate their positions, tyre sizes and pulses per revolution for the installation. Racelogic specifies saturated injector signals, and warns against peak-and-hold or PWM injector drive and injectors under 4 ohms; confirm the actual ECU and injectors before installation. Manufacturer fitting instructions; calibration instructions.
A20 CSWITCH must not be connected to a 12 V clutch feed; Racelogic calls for an independent switch between this input and ground. The manufacturer warns that applying 12 V causes hardware damage. Racelogic full-throttle shift instructions.
Documented installation examples
Racelogic's fitting guide shows its launch button and manual slip adjuster installed in a Nissan 300ZX and a manual slip adjuster in a Holden HSV. These are examples of aftermarket installations, not evidence of factory fitment or compatibility across every engine and variant. The manual also discusses Nissan 200SX installations with a single differential-mounted rear speed sensor: automatic calibration is unavailable in that configuration and software setup is required. Racelogic fitting examples; manual, section 1.11, printed pages 25–26.