
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Subaru 2006-2014 S7Plus, with product code S7Plus-SUB0614. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Subaru 2006-2014 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Subaru 2006-2014 S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Complete manufacturer connector schedule
The following is the ECU-side S7Plus A/B/C schedule and corresponding Impreza loom connections from the Syvecs Subaru Impreza 2006–2014 manual v1.2, page 5. ECU letters A/B/C are not the same as the vehicle's four connector letters A/B/C/D; identify both using the manual diagrams. Blank entries mean the source leaves the application column blank, not proof that a pin is electrically unused. Asterisks reproduce source markings; check their meaning with Syvecs. The manufacturer specifies high-impedance injectors for the fuel outputs, and hardware jumpers or solder bridges for selected outputs. Verify pull-ups, flyback protection, wiring orientation and ECU/harness revision against the manual.
Syvecs connector A: 34-way (4-1437290-0, key 1)
| Syvecs pin | Syvecs signal | Impreza connection | Application / notes |
|---|---|---|---|
| A1 | PWR CTR OUT | B23 | Main relay |
| A2 | H-Bridge1 | D4* | DBW+ |
| A3 | H-Bridge2 | D5* | DBW− |
| A4 | H-Bridge3 | B20 | Starter relay |
| A5 | H-Bridge4 | B22 | Tacho |
| A6 | H-Bridge5 | D12 | Tumble generator open LH |
| A7 | H-Bridge6 | D13 | Tumble generator close LH |
| A8 | H-Bridge7 | D22 | Tumble generator open RH |
| A9 | H-Bridge8 | D23 | Tumble generator close RH |
| A10 | FUEL1 | D8 | Injector 1 |
| A11 | FUEL2 | D9 | Injector 2 |
| A12 | FUEL3 | D10 | Injector 3 |
| A13 | FUEL4 | D11 | Injector 4 |
| A14 | FUEL5 | — | — |
| A15 | FUEL6 | — | — |
| A16 | FUEL7 | — | — |
| A17 | FUEL8 | — | — |
| A18 | PWM1 *FUEL9-SB20 (12V 470R pullup) | B18 | Rad fan |
| A19 | PWM2 *FUEL10-SB23 (12V 470R pullup) | B29 | Rad fan 2 |
| A20 | PWM3 *FUEL11-SB24 (5V 470R pullup) | B10 (5V pullup) | Alternator |
| A21 | PWM4 *FUEL12-SB26 (5V 470R pullup) | B9 | A/C relay |
| A22 | PWM5-SB27 (flyback diode) | D14 (diode) | VVT OCV LH inlet |
| A23 | PWM6-SB29 (flyback diode) | D16 (diode) | VVT OCV RH inlet |
| A24 | PWM7-SB32 (flyback diode) | D30 (diode) | VVT OCV LH exhaust |
| A25 | PWM8-SB35 (flyback diode) | D24 (diode) | VVT OCV RH exhaust |
| A26 | IGN1 | D18 | Ignition coil 1 |
| A27 | IGN2 | D19 | Ignition coil 2 |
| A28 | IGN3 | D20 | Ignition coil 3 |
| A29 | IGN4 | D21 | Ignition coil 4 |
| A30 | IGN5 | B12 | Fuel pump control |
| A31 | IGN6 | D27 | Wastegate; IGBT |
| A32 | PWRGND | A35, B6 | Airflow shield, PPS shield |
| A33 | PWRGND | D1, D2, D3 | Power ground |
| A34 | PWRGND | D6, D7, D26, C24, C25 | Power ground |
Syvecs connector B: 26-way (3-1437290-7, key 1)
| Syvecs pin | Syvecs signal | Impreza connection | Application / notes |
|---|---|---|---|
| B1 | PWRGND | A1, C5 | Power ground |
| B2 | EGT2+ | — | — |
| B3 | EGT2− | — | — |
| B4 | KNOCK | C15 | Knock signal |
| B5 | KNOCK2 | — | — |
| B6 | PVBAT | A5 | Constant 12V supply |
| B7 | IVBAT | A2 | Linked 12V feed, normally from main relay |
| B8 | LAM1A | Grey NTK | Denso lambda; Nernst cell |
| B9 | LAM1B | White NTK | Denso lambda; ion pump |
| B10 | LAM1C | A20 | Brake switch 1; cal trim resistor |
| B11 | LAM1D | Black NTK | Virtual ground |
| B12 | LAM1HEATER | Blue NTK | Denso lambda |
| B13 | IVBAT | Yellow NTK | — |
| B14 | LAM2A | C16 | Tumble generator signal LH; solder bridge |
| B15 | LAM2B | — | — |
| B16 | LAM2C | C26* | Solder bridge |
| B17 | LAM2D | — | — |
| B18 | LAM2HEATER | B4 | — |
| B19 | IVBAT | D15, D17, D25, D31 | VVT OCV + LH inlet, VVT OCV + RH inlet; linked 12V feed |
| B20 | KLINE | B16 | K-line interface for OBDII |
| B21 | RS232RX | — | RS232 receive |
| B22 | RS232TX | — | RS232 transmit |
| B23 | LANRX− | — | Orange/white |
| B24 | LANRX+ | — | White/orange |
| B25 | LANTX− | — | Green/white |
| B26 | LANTX+ | — | White/green |
Syvecs connector C: 34-way (4-1437290-1, key 2)
| Syvecs pin | Syvecs signal | Impreza connection | Application / notes |
|---|---|---|---|
| C1 | KNOCK GROUND | — | Knock ground |
| C2 | ANGND | A29, A30, A34 | PPS ground, MAF ground |
| C3 | ANGND | C14, C22, C29 | Crank ground |
| C4 | ANGND | — | Accelerator pedal shield/ECU ground |
| C5 | 5V OUT | A21, A22 | — |
| C6 | 5V OUT | C19 | TPS 5V |
| C7 | 5V OUT | — | — |
| C8 | CAN L | B35 | — |
| C9 | CAN H | B27 | — |
| C10 | AN01 | C13 | Crank signal |
| C11 | AN02 | C6 | MAP signal |
| C12 | AN03 | A4 | Rear O2 |
| C13 | AN04 | A26* | Air flow signal |
| C14 | AN05 | C21 | Intake cam signal LH |
| C15 | AN06 | C11 | Intake cam signal RH |
| C16 | AN07 | C31 | Exhaust cam signal LH |
| C17 | AN08 | C12 | Exhaust cam signal RH |
| C18 | AN09 | A23 | Pedal sensor 1 |
| C19 | AN10 | A31 | Pedal sensor 2 |
| C20 | AN11 | C18 | TPS1 |
| C21 | AN12 | C28 | TPS2 |
| C22 | AN13 | C34 | Coolant temperature |
| C23 | AN14 | A18 | Air charge temperature |
| C24 | AN15 | B31 | Neutral switch |
| C25 | AN16 | C33 | Power steering switch |
| C26 | EGT1− | — | — |
| C27 | EGT1+ | — | — |
| C28 | PWR CTR IN | A19 | Ignition switch; main relay input switch supply |
| C29 | AN S1 / Slave An01 | B25 | Clutch switch |
| C30 | AN S2 / Slave An02 | A12 | Cruise main switch |
| C31 | AN S3 / Slave An03 | A28 | Brake switch 2 |
| C32 | AN S4 / Slave An04 | B24 | A/C switch |
| C33 | AN S5 / Slave An05 | A24 | Cruise command switch |
| C34 | AN S6 / Slave An06 | B13 | A/C middle switch |