Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
AEM EMS Series 2
Applies to
AEM EMS Series 2
Tool groups
None
Manufacturers
None

The AEM EMS Series 2 30-6050 is an application-specific plug-in engine management system. It uses the vehicle connector assignments shown in its own manufacturer installation manual; other Series 2 part numbers must not be assumed to share this schedule.

AEM 30-6052 shown as a Series 2 family illustration; connectors and applications can differ
AEM 30-6052 shown as a Series 2 family illustration; connectors and applications can differ. Source: AEM / Holley product listing; reproduced with permission.

Applications and identification

The manual cover identifies 2000–2001 Acura Integra and 1998–1999 Acura 2.3CL; the connector chart heading also mentions 1998–2002 Accord and 1999–2000 Civic. Because the cover and chart differ, verify the actual part number and vehicle application with AEM before installation.

Connector pin assignments

The following tables transcribe the connector schedule in the AEM 30-6050 installation manual, PDF pages 8, 9, 10, 11. The manufacturer labels each position with its original vehicle function and its EMS function, I/O direction and notes. Follow the connector diagram and viewing orientation in that manual. A dash reflects the manufacturer’s entry and does not by itself establish an unused or safe connection. Where a channel is configurable, its actual use also depends on the wiring and calibration.

Connector A

PinOriginal vehicle functionAEM EMS functionI/OManufacturer notes
A1---Coolant dash signalOutputDedicated, for use with S2000 dash
A2---Low Side Driver 1OutputAvail, Switched Ground, 1.5A Max
A3EVAP Bypass Solenoid ValveLow Side Driver 3OutputPnP For Bypass Solenoid
A4EVAP Control Canister VentLow Side Driver 5OutputPnP For Control Canister Vent
A5---EGT 1InputAvail, jumper set for 0–5V Input
A6EVAP Purge Control SolenoidLow Side Driver 4OutputPnP For EVAP Purge Control
A7---Sensor GroundOutputAvail, Sensor Ground
A8Secondary 02 Heater ControlLow Side Driver 12OutputAvail, Switched Ground, 1.5A Max
A9---T3 (Vehicle Speed)Input**This pin connects to C23 also**
A10Service Check SignalInjector 12OutputAvail, Switched Ground, 1.5A Max
A11---PW3OutputAvail, Switched Ground, 1.5A Max
A12---Injector 9OutputAvail, Switched Ground, 1.5A Max
A13---Coil 7OutputAvail, 0/5V falling edge signal
A14---Injector 11OutputAvail, Switched Ground, 1.5A Max
A15---Low Side Driver 11Output**This pin connects to A16 also**
A16Fuel Pump RelayLow Side Driver 11OutputPnP For Fuel Pump
A17A/C Clutch RelayLow Side Driver 6OutputPnP For A/C Clutch
A18Malfunction Indicator LightLow Side Driver 10OutputPnP For MIL
A19Engine Speed PulseTach Output (LS7)OutputPnP For Tach
A20Radiator Fan ControlLow Side Driver 8OutputPnP For Rad Fan Control
A21K-Line+12V SwitchedOutputDedicated, filtered 12V power
A22---Coil 8OutputAvail, 0/5V falling edge signal
A23Secondary O2 SensorLambda #2InputPnP For Lambda 32
A24Starter Switch SignalCrankingInputPnP For Starter Switch
A25---Idle #3OutputAvail, Switched Ground, 1.5A Max
A26P/S Pressure SwitchSwitch 5InputAvail, Switch must connect to ground
A27A/C Switch SignalSwitch 6InputPnP For A/C Request
A28---Idle #2OutputAvail, Switched +12V, 1.5A Max
A29Fuel Tank Pressure SensorMAFInputAvail, 0–5V Input
A30Electrical Load DetectorEGT #3InputAvail, jumper set for 0–5V Input
A31---Sensor GroundOutputAvail, Sensor Ground
A32Brake Switch SignalSwitch 1InputAvail, Switched Input

Connector B

PinOriginal vehicle functionAEM EMS functionI/OManufacturer notes
B1Power Source 1+12V SwitchedBothDedicated
B2Power Ground 1Power GroundBothDedicated
B3Injector 2Injector 2OutputPnP For Injector 2
B4Injector 3Injector 3OutputPnP For Injector 3
B5Injector 4Injector 4OutputPnP For Injector 4
B6Idle Air Control Valve +PW 1iOutputPnP For Idle Control Solenoid
B7---High Side Driver 2OutputAvail, Switched +12V, 1.5A Max
B8---Idle #5OutputAvail, Switched Ground, 1.5A Max
B9Power Source 2+12V SwitchedBothDedicated
B10Power Ground 2Power GroundBothDedicated
B11Injector 1Injector 1OutputPnP For Injector 1
B12VTEC solenoid ValveHigh Side Driver 1OutputPnP For VTEC Solenoid
B13Ignition Control ModuleCoil 1OutputPnP Coil 1, Rising Edge trigger
B14---------Not Used
B15Idle Air Control Valve -PW1OutputPnP For Idle Control Solenoid
B16Intake Air Bypass SolenoidInjector 8OutputPnP For IAB Solenoid
B17---Idle #6OutputAvail, Switched +12V, 1.5A Max
B18---Idle #7OutputAvail, Switched Ground, 1.5A Max
B19---Injector 6OutputAvail, Switched Ground, 1.5A Max
B20Logic Ground 1Power GroundBothDedicated
B21Voltage Back UpPermanent +12VInputPnP For Perm Power
B22Logic Ground 2Power GroundBothDedicated
B23Idle Air Control ValvePW1OutputPnP For Idle Control Motor
B24---Knock 2InputAvailable, software knock filter
B25---Idle #8OutputAvail, Switched +12V, 1.5A Max

Connector C

PinOriginal vehicle functionAEM EMS functionI/OManufacturer notes
C1Primary O2 Heater ControlLow Side Driver 2OutputAvail, Switched Ground, 1.5A Max
C2Alternator Control------Not Used
C3Knock Sensor 1Knock 1InputPnP For Knock 1
C4---Coil 1Output**This pin connects to B13 also**
C5Alternator FR SignalEGT #4InputAvail, jumper set for 0–5V Input
C6---ADCR11InputAvailable, 0–5V in
C7Sensor Ground 1Sensor GroundOutputDedicated, Sensors only
C8CKP +Crank SensorInputPnP For Crank Sensor
C9CKP -Timing GroundOutputPnP For Timing Ground
C10VTEC Pressure Switch SignalSwitch 4InputPnP For VTEC Oil Press Sw
C11---Injector 10OutputAvail, Switched Ground, 1.5A Max
C12---Coil 2OutputAvail, Coil Output
C13---Coil 3OutputAvail, Coil Output
C14---Coil 4OutputAvail, Coil Output
C15---Lambda 2InputAvail, 0–5V Lambda 2 input
C16Primary O2 SensorLambda 1InputAvail, 0–5V Lambda 1 input
C17MAP SensorMAPInputPnP For 0-5V MAP Sensor
C18Sensor Ground 2Sensor GroundOutputDedicated, Sensors only
C19Sensor Voltage 1+5V SensorOutputDedicated, Sensors only
C20TDC +T4 (Spare Speed)InputAvail, Speed Input
C21TDC -Timing GroundOutputAvail, Speed Ground
C22Crank Fluctuation SensorKnock #2InputAvail, Knock Sensor
C23Vehicle Speed SensorT3 (Vehicle Speed)InputPnP Vehicle Speed Sensor
C24---ADCR13InputAvailable, 0–5V in, 100k pull up to 5V
C25Intake Air Temp SensorAITInputPnP AIT Sensor
C26Engine Coolant Temp SensorCoolantInputPnP ECT Sensor
C27Throttle Position SensorTPSInputPnP TPS Sensor
C28Sensor Voltage 2+5V SensorOutputPnP Sensor Vcc
C29CYP +CamInputDedicated, Cam Sensor
C30CYP -Timing GroundOutputDedicated
C31Timing GroundTiming GroundOutputDedicated

Connector D

PinOriginal vehicle functionAEM EMS functionI/OManufacturer notes
D1---Injector 5OutputAvail, Switched Ground, 1.5A Max
D2---Injector 7OutputAvail, Switched Ground, 1.5A Max
D3---Idle #1OutputAvail, Switched Ground, 1.5A Max
D4---High Side Driver 4OutputAvail, Switched +12V, 1.5A Max
D5---Idle #4OutputAvail, Switched +12V, 1.5A Max
D6---+5V SensorOutputAvail, 5V sensor reference power
D7---EGT #2InputAvail, jumper set for 0–5V Input
D8---ADCR14InputAvailable, 0–5V in, 100k pull up to 5V
D9---Sensor GroundOutputAvail, Sensor Ground
D10---CAN1H---Dedicated
D11---Switch 2InputAvail, Switched GND Input
D12---Switch 3InputAvail, Switched GND Input
D13---High Side Driver 3OutputAvail, Switched +12V, 1.5A Max
D14---CAN1L---Dedicated
D15---Baro Volts---Avail, 0–5V input
D16---PW 2OutputAvail, Boost Solenoid Output

Documentation

AEM 30-6050 Series 2 installation instructions and wiring chart. AEM engine management support archive.