Removed text is struck through; added text is highlighted.
Syvecs S12 standalone ECU shown as a family illustration. This vehicle-specific kit and its adapter or wiring are not pictured and may differ. Image: Syvecs, reproduced with permission.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi R8 Gen2 2016 onward V10 S12, with product code S12-R8V1017. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi R8 Gen2 2016 onward V10 S12 installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Audi R8 Gen2 2016 onward V10 S12 product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer S12 ECU connector schedule
From the Syvecs Huracán / R8 Gen2 kit installation guide, pages 9–11. This covers the 121 S12 ECU positions and manufacturer descriptions; the separate DI12 and factory vehicle connectors are not fully tabulated here. The chart's guide identifies the R8 Gen2 interface as 2017 onward, while the article's product range begins in 2016; confirm a 2016 vehicle and loom with Syvecs. A dash reproduces an empty entry in the chart.
Open each version to inspect formatting, tables and photographs.
Revision 3: Syvecs Audi R8 Gen2 2016 onward V10 S12 Plug-in ECUSyvecs S12 standalone ECU shown as a family illustration. This vehicle-specific kit and its adapter or wiring are not pictured and may differ. Image: Syvecs, reproduced with permission.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi R8 Gen2 2016 onward V10 S12, with product code S12-R8V1017. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi R8 Gen2 2016 onward V10 S12 installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Huracán / R8 Gen2 kit installation guide, pages 9–11. This covers the 121 S12 ECU positions and manufacturer descriptions; the separate DI12 and factory vehicle connectors are not fully tabulated here. The chart's guide identifies the R8 Gen2 interface as 2017 onward, while the article's product range begins in 2016; confirm a 2016 vehicle and loom with Syvecs. A dash reproduces an empty entry in the chart.
S12 pin
Syvecs function
Kit description
1
PWRGND
—
2
IGN01
Ignition Coil Cyl 1
3
IGN02
Ignition Coil Cyl 2
4
IGN03
Ignition Coil Cyl 3
5
IGN04
Ignition Coil Cyl 4
6
IN25
Throttle Position 1a
7
KNOCK 4
Knock + 4
8
KNOCKGND
Knock Ground
9
THERMO 2 + _
—
10
IN21
MAF Air Temp 1
11
IN18
Pedal Position 1a
12
IN14
Cam Position ‐ Exhaust 1
13
IN11
Cam Position ‐ Intake 1
14
IN07
Crank Position
15
IN04
Starter Signal
16
IN01
—
17
LAM 1 I
—
18
CAN 2 LO
—
19
RS232 TX
—
20
LAN RX‐
Orange/White
21
FUEL07
Sec Fuel Injector 1
22
FUEL03
Sec Fuel Injector 2
23
VBAT
—
24
PWRGND
—
25
IN26
Throttle Position 1b
26
5V OUT
—
27
KNOCK 1
Knock + 1
28
THERMO 1 ‐ _
—
29
IN22
MAF Air Temp 2
30
IN19
Pedal Position 1b
31
IN15
Cam Position ‐ Exhaust 2
32
IN12
Cam Position ‐ Intake 2
33
IN08
External Map Sensor
34
ANGND
Tank Pressure, Cam Sensor,
35
IN02
—
36
LAM 1 V
Nernst Cell V
37
CAN 3 HI
—
38
RS232 RX
—
39
LAN RX+
White/Orange
40
FUEL08
Sec Fuel Injector 3
41
FUEL04
Sec Fuel Injector 4
42
VBAT
—
43
PWRGND
—
44
IN27
Throttle Position 2a
45
5V OUT
—
46
KNOCK 2
Knock + 2
47
THERMO 1 + _
—
48
IN23
—
49
IN20
Fuel Pressure ‐ Low Side1
50
IN16
Sec Air Pressure ( MAP 1)
51
ANGND
—
52
IN09
Sec Air Pressure ( MAP 2)
53
IN05
Brake Light Switch
54
ANGND
—
55
LAM 2 V
Neret Cell V
56
CAN 3 LO
—
57
RS232 GND
—
58
CAN 1 HI
—
59
LAN TX‐
Green/White
60
FUEL05
Sec Fuel Injector 5
61
FUEL01
Sec Fuel Injector 6
62
HBRIDGE 6
DBW 1b ‐
63
IN28
Throttle Position 2b
64
10VOUT
—
65
KNOCK 3
Knock + 3
66
THERMO 2 ‐ _
—
67
IN24
Coolant Temp 1
68
ANGND
—
69
IN17
Fuel Pressure ‐ Low Side2
70
IN13
Fuel Pressure ‐ High Side 1
71
IN10
Fuel Pressure ‐ High Side2
72
IN06
—
73
IN03
Oil Pressure SWiTCH
74
LAM 2 I
—
75
LAM GND
—
76
CAN 2 HI
—
77
CAN 1 LO
—
78
LAN TX+
White/Green
79
FUEL06
Sec Fuel Injector 7
80
FUEL02
Sec Fuel Injector 8
81
HBRIDGE 5
DBW 1 +
82
HBRIDGE 2
DI Spill Valve 2 ‐ 12V
83
PWM4
Lambda Heater B1
84
PWM8
Lambda Heater B2
85
FUEL12
Sec Fuel Injector 9
86
FUEL16
Sec Fuel Injector 10
87
FUEL20
Cam Adjuster B1 Intake
88
FUEL24
Cam Adjuster B1 Exhaust
89
VBAT
—
90
HBRIDGE 1
DI Spill Valve 1 ‐ 12v
91
PWM3
Starter Relays
92
PWM7
Brake Servo Relay
93
FUEL11
Cam Adjuster B2 Intake
94
FUEL15
Cam Adjuster B2 Exhaust
95
FUEL19
DI12 Injector 1
96
FUEL23
DI12 Injector 2
97
PWRGND
—
98
HBRIDGE 4
DBW 2 ‐
99
PWM2
—
100
PWM6
Boost control Sol
101
FUEL10
DI12 Injector 3
102
FUEL14
DI12 Injector 4
103
FUEL18
DI12 Injector 5
104
FUEL22
DI12 Injector 6
105
PWRGND
—
106
HBRIDGE 3
DBW 2 +
107
PWM1
FuelPump
108
PWM5
Cooling Fans
109
FUEL09
DI12 Injector 7
110
FUEL13
DI12 Injector 8
111
FUEL17
DI12 Injector 9
112
FUEL21
DI12 Injector 10
113
PWRGND
—
114
IGN05
Ignition Coil Cyl 5
115
IGN06
Ignition Coil Cyl 6
116
IGN07
Ignition Coil Cyl 7
117
IGN08
Ignition Coil Cyl 8
118
IGN09
Ignition Coil Cyl 9
119
IGN10
Ignition Coil Cyl 10
120
IGN11
DI Spill Valve 1
121
IGN12
DI Spill Valve 2
Revision 3: Syvecs Audi R8 Gen2 2016 onward V10 S12 Plug-in ECUSyvecs S12 standalone ECU shown as a family illustration. This vehicle-specific kit and its adapter or wiring are not pictured and may differ. Image: Syvecs, reproduced with permission.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi R8 Gen2 2016 onward V10 S12, with product code S12-R8V1017. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi R8 Gen2 2016 onward V10 S12 installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Huracán / R8 Gen2 kit installation guide, pages 9–11. This covers the 121 S12 ECU positions and manufacturer descriptions; the separate DI12 and factory vehicle connectors are not fully tabulated here. The chart's guide identifies the R8 Gen2 interface as 2017 onward, while the article's product range begins in 2016; confirm a 2016 vehicle and loom with Syvecs. A dash reproduces an empty entry in the chart.