
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi RS3 8Y1 Pre Facelift S7D, with product code S7D-RS38Y!YDF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
The manufacturer product page displays the code S7D-RS38Y!YDF, including an exclamation mark. Treat this transcription as uncertain and confirm the part number with Syvecs before ordering.
Wiring and pinout
Syvecs Audi RS3 8Y1 Pre Facelift S7D installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Audi RS3 8Y1 Pre Facelift S7D product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer S7D and accessory connector schedules
From Syvecs' RS3 8Y1 S7D kit guide, pages 8–10. The tables describe the Syvecs-side connectors and accessory plug, alongside the manual's OEM function column; they are not the full factory harness pinout. Blank cells reproduce unspecified entries. Accessory B positions belong to the separate accessory plug and must not be confused with ECU connector B. Confirm model, board and loom revision before use. The manuals for 8Y1 and 8Y2 have differing C-connector mappings, including MAP and pedal inputs.
ECU connector A: 34-way, key 1
| Pin | Syvecs signal | Function | OEM / kit function |
|---|---|---|---|
| A1 | PWR CTR OUT | Main relay output | — |
| A2 | H-Bridge 1 | H-Bridge 1 | DBW + |
| A3 | H-Bridge 2 | H-Bridge 2 | DBW − |
| A4 | H-Bridge 3 | H-Bridge 3 | Wastegate solenoid |
| A5 | H-Bridge 4 | H-Bridge 4 | EVAP |
| A6 | H-Bridge 5 | H-Bridge 5 | Spare output |
| A7 | H-Bridge 6 | H-Bridge 6 | Starter relay |
| A8 | H-Bridge 7 | H-Bridge 7 | Intake manifold flap (N316) |
| A9 | H-Bridge 8 | H-Bridge 8 | Coolant switch pump |
| A10 | GDI LS1 | Fuel 1 / low side GDI 1 | Spare output |
| A11 | GDI LS2 | Low side GDI 2 | Injector 4 − |
| A12 | GDI LS3 | Fuel 3 / low side GDI 3 | Port injector 1 (N532) |
| A13 | GDI LS4 | Low side GDI 4 | Injector 2 − |
| A14 | GDI LS5 | Fuel 5 / low side GDI 5 | Port injector 2 (N533) |
| A15 | GDI LS6 | Low side GDI 6 | Injector 5 − |
| A16 | GDI LS7 | Fuel 7 / low side GDI 7 | Port injector 3 (N534) |
| A17 | GDI LS8 | Low side GDI 8 | Injector 3 − |
| A18 | GDI HS1/2 | GDI high side 1–2 | Injector 4 + |
| A19 | GDI HS3/4 | GDI high side 3–4 | Injector 2 + |
| A20 | GDI Pump 1 HS | GDI pump 1 high side | GDI pump HS |
| A21 | GDI HS5/6 | GDI high side 5–6 | Injector 5 + |
| A22 | GDI HS7/8 | GDI high side 7–8 | Injector 3 + |
| A23 | GDI Pump 2 HS | GDI pump 2 high side | Injector 1 + |
| A24 | GDI Pump 1 LowSide | GDI pump 1 low side / fuel 15 | GDI pump LS |
| A25 | GDI Pump 2 LowSide / Injector LS | GDI pump 2 low side / fuel 16 | Injector 1 − |
| A26 | IGN1 | Cylinder 1 ignition output | IGN1 (N70) |
| A27 | IGN2 | Cylinder 2 ignition output | IGN2 (N127) |
| A28 | IGN3 | Cylinder 3 ignition output | IGN3 (N291) |
| A29 | IGN4 | Cylinder 4 ignition output | IGN4 (N292) |
| A30 | IGN5 | Cylinder 5 ignition output | IGN5 (N292) |
| A31 | IGN6 | Cylinder 6 ignition output | Tacho sync |
| A32 | PWRGND | Power ground | PwrGnd |
| A33 | PWRGND | Power ground | PwrGnd |
| A34 | PWRGND | Power ground | PwrGnd |
ECU connector B: 26-way, key 1
| Pin | Syvecs signal | Function | OEM / kit function |
|---|---|---|---|
| B1 | PWRGND | Power ground | PwrGnd |
| B2 | CAN2 L | CAN 2 | — |
| B3 | CAN2 H | CAN 2 | — |
| B4 | KNOCK 1 | Knock 1 | — |
| B5 | KNOCK 2 | Knock 2 | — |
| B6 | PVBAT | Constant 12 V | — |
| B7 | IVBAT | 12 V | — |
| B8 | LAM1A | LamV / LamD1+ / LamLun1 | — |
| B9 | LAM1B | LamI / LamD1− / LamIP1 | — |
| B10 | LAM1C | LamLIA1 | — |
| B11 | LAM1D | LamGND / LamLVM1 | — |
| B12 | LAM1HEATER | Lambda heater | — |
| B13 | IVBAT | 12 V | — |
| B14 | LAM2A | LamV / LamD1+ / LamLun1 | — |
| B15 | LAM2B | LamI / LamD1− / LamIP1 | — |
| B16 | LAM2C | LamLIA1 | — |
| B17 | LAM2D | LamGND / LamLVM1 | — |
| B18 | LAM2HEATER | Lambda heater | — |
| B19 | IVBAT | 12 V | — |
| B20 | KLINE | KLINE | — |
| B21 | RS232RX | RS232 RX | — |
| B22 | RS232TX | RS232 TX | — |
| B23 | LANRX− | Cat5 pin 2 | — |
| B24 | LANRX+ | Cat5 pin 1 | — |
| B25 | LANTX− | Cat5 pin 6 | — |
| B26 | LANTX+ | Cat5 pin 3 | — |
ECU connector C: 34-way, key 2
| Pin | Syvecs signal | Function | OEM / kit function |
|---|---|---|---|
| C1 | KNOCKGND | Knock ground | Knock − |
| C2 | ANGND | Sensor ground | Tested |
| C3 | ANGND | Sensor ground | Tested |
| C4 | ANGND | Sensor ground | — |
| C5 | 5V OUT | 5 V out | Tested |
| C6 | 5V OUT | 5 V out | Tested |
| C7 | 5V OUT | 5 V out | — |
| C8 | CAN1 L | CAN 1 low | Powertrain CAN |
| C9 | CAN1 H | CAN 1 high | Powertrain CAN |
| C10 | AN01 | Bi-polar input | Start request |
| C11 | AN02 | Bi-polar input | DI pressure |
| C12 | AN03 | Bi-polar input | — |
| C13 | AN04 | Bi-polar input | — |
| C14 | AN05 | Uni-polar input | VVT1 intake position |
| C15 | AN06 | Uni-polar input | VVT1 exhaust position |
| C16 | AN07 | Uni-polar input | Crank sensor |
| C17 | AN08 | Uni-polar input | Brake light switch |
| C18 | AN09 | Volt input | TPS1A |
| C19 | AN10 | Volt input | TPS1B |
| C20 | AN11 | Volt input | PPSA |
| C21 | AN12 | Volt input | PPSB |
| C22 | AN13 | Resistive input | Coolant temperature (G62) |
| C23 | AN14 | Resistive input | Intake air temperature |
| C24 | AN15 | Resistive input | EGT1 |
| C25 | AN16 | Resistive input | EGT2 |
| C26 | EGT1− | EGT1 − | — |
| C27 | EGT1+ | EGT1 + | — |
| C28 | PWR CTR IN | Main relay input switch | Key on signal (15) |
| C29 | AN S1 | Uni-polar input | Intake position flap |
| C30 | AN S2 | Uni-polar input | Fuel pressure low side |
| C31 | AN S3 | Uni-polar input | SENT MAP |
| C32 | AN S4 | Uni-polar input | SENT ACT |
| C33 | AN S5 | Uni-polar input | Pre-throttle MAP |
| C34 | AN S6 | Uni-polar input | Intermediate shaft speed |
ECU connector D: 26-way, key 2
| Pin | Syvecs signal | Function | OEM / kit function |
|---|---|---|---|
| D1 | DVBAT1 | GDI power supply | — |
| D2 | DVBAT2 | GDI power supply | — |
| D3 | DVBAT3 | GDI power supply | — |
| D4 | DVBAT4 | GDI power supply | — |
| D5 | FUEL9 | PWM / fuel output | Port injector 4 (N535) |
| D6 | FUEL10 | PWM / fuel output | Port injector 5 (N536) |
| D7 | FUEL11 | PWM / fuel output | Fuel pump PWM |
| D8 | FUEL12 | PWM / fuel output | Cooling fan PWM |
| D9 | FUEL13 | PWM / fuel output | Turbo recirc (N249) |
| D10 | FUEL14 | PWM / fuel output | Exhaust cam solenoids A |
| D11 | LSO1 | PWM output | VVT1 intake (N205) |
| D12 | LSO2 | PWM output | VVT1 exhaust (N316) |
| D13 | LSO3 | PWM output | Oil pressure valve |
| D14 | LSO4 | PWM output | Crank case breather |
| D15 | LSO5 | PWM output | Coolant shut-off valve |
| D16 | LSO6 | PWM output | Coolant pump PWM |
| D17 | EGT2− | EGT2 − | — |
| D18 | EGT2+ | EGT2 + | — |
| D19 | NC | NC | — |
| D20 | NC | NC | — |
| D21 | NC | NC | — |
| D22 | NC | NC | — |
| D23 | CAN3L | CAN3L | CAN3L |
| D24 | CAN3H | CAN3H | CAN3H |
| D25 | PWRGND | Power ground | — |
| D26 | PWRGND | Power ground | — |
Accessory connector: 26-way key 1
| Accessory pin | Signal | Documented use |
|---|---|---|
| B1 | GND | Ground |
| B2 | Fuel 1 | Spare output |
| B3 | LSO3 | Spare output − slave 1 out 13 |
| B4 | LSO4 | Spare output − slave 1 out 14 |
| B5 | LSO5 | Spare output − slave 1 out 15 |
| B6 | LSO6 | Spare output − slave 1 out 16 |
| B7 | 12 V | — |
| B8 | H-Bridge 5 | Spare output − slave 1 out 5 |
| B9 | CAN2L | Spare CAN |
| B10 | CAN2H | Spare CAN |
| B11 | RS232RX | — |
| B12 | RS232TX | — |
| B13 | LAM2A | Spare input − S1AN08 |
| B14 | EGT1− | K-type EGT |
| B15 | EGT1+ | K-type EGT |
| B16 | AN03 | Spare input − bipolar |
| B17 | AN04 | Spare input − bipolar |
| B18 | AN15 | Spare input |
| B19 | AN16 | Spare input |
| B20 | S1AN4 | Spare input if non-SENT MAP is used |
| B21 | ANGround | Sensor ground |
| B22 | 5V Out | 5 V output for sensors |
| B23 | Cat5 pin 2 | Ethernet |
| B24 | Cat5 pin 1 | Ethernet |
| B25 | Cat5 pin 6 | Ethernet |
| B26 | Cat5 pin 3 | Ethernet |
The Syvecs source labels both IGN4 and IGN5 as N292 in its OEM column and repeats Lambda 1-style names for the second lambda bank. Those labels are reproduced as printed and should be checked with Syvecs before wiring.