Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
DTAFast standalone engine management
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

DTAFast S-series family photograph, illustrating related S-series hardware; this is not a model-specific photograph of the ignition-only variant. Source: DTAFast. Permission to republish confirmed by the user.

DTAFast's S-series feature matrix states that an ignition-only S40 version was available. A distributor lists it as S40i; identify the exact case label and firmware rather than assuming that every S40 has functioning fuel outputs. Manufacturer document.

Identification and operating context

This is included for identification as an ignition controller. Record the exact product label, hardware, firmware and loom; do not assume compatibility with a similarly named fuel-and-ignition ECU. See DTAFast family overview.

Wiring

The manufacturer S40 Pro diagram is a family reference, not proof that every function is populated in an ignition-only ECU. Obtain the exact build information from DTAFast before wiring. DTAFast wiring reference. Establish fused supplies, grounds, sensor connections and coil-driver limits for the specific unit.

Documented gearshift controller connections (partial)

TTT Racing explicitly identifies the DTA S40 and S40 Ignition in its TTT802 interface guide, revision 8, pages 2–4. This is an application-specific connection list, not a complete ECU pinout. The descriptions below identify the TTT802 wire function rather than asserting the full electrical specification of each ECU pin; configure and verify the ECU and hardware before connection.

DTA ECU pinTTT802 connection described by the guide11Red — cut open-collector28Blue — cut ground26White — ignition pulse13 or 14Black — ignition pulse ground

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: DTAFast S40 ignition only
DTAFast S-series family ECU photograph
DTAFast S-series family photograph, illustrating related S-series hardware; this is not a model-specific photograph of the ignition-only variant. Source: DTAFast. Permission to republish confirmed by the user.

DTAFast's S-series feature matrix states that an ignition-only S40 version was available. A distributor lists it as S40i; identify the exact case label and firmware rather than assuming that every S40 has functioning fuel outputs. Manufacturer document.

Identification and operating context

This is included for identification as an ignition controller. Record the exact product label, hardware, firmware and loom; do not assume compatibility with a similarly named fuel-and-ignition ECU. See DTAFast family overview.

Wiring

The manufacturer S40 Pro diagram is a family reference, not proof that every function is populated in an ignition-only ECU. Obtain the exact build information from DTAFast before wiring. DTAFast wiring reference. Establish fused supplies, grounds, sensor connections and coil-driver limits for the specific unit.

Documented gearshift controller connections (partial)

TTT Racing explicitly identifies the DTA S40 and S40 Ignition in its TTT802 interface guide, revision 8, pages 2–4. This is an application-specific connection list, not a complete ECU pinout. The descriptions below identify the TTT802 wire function rather than asserting the full electrical specification of each ECU pin; configure and verify the ECU and hardware before connection.

DTA ECU pinTTT802 connection described by the guide
11Red — cut open-collector
28Blue — cut ground
26White — ignition pulse
13 or 14Black — ignition pulse ground
Revision 3: DTAFast S40 ignition only
DTAFast S-series family ECU photograph
DTAFast S-series family photograph, illustrating related S-series hardware; this is not a model-specific photograph of the ignition-only variant. Source: DTAFast. Permission to republish confirmed by the user.

DTAFast's S-series feature matrix states that an ignition-only S40 version was available. A distributor lists it as S40i; identify the exact case label and firmware rather than assuming that every S40 has functioning fuel outputs. Manufacturer document.

Identification and operating context

This is included for identification as an ignition controller. Record the exact product label, hardware, firmware and loom; do not assume compatibility with a similarly named fuel-and-ignition ECU. See DTAFast family overview.

Wiring

The manufacturer S40 Pro diagram is a family reference, not proof that every function is populated in an ignition-only ECU. Obtain the exact build information from DTAFast before wiring. DTAFast wiring reference. Establish fused supplies, grounds, sensor connections and coil-driver limits for the specific unit.

Documented gearshift controller connections (partial)

TTT Racing explicitly identifies the DTA S40 and S40 Ignition in its TTT802 interface guide, revision 8, pages 2–4. This is an application-specific connection list, not a complete ECU pinout. The descriptions below identify the TTT802 wire function rather than asserting the full electrical specification of each ECU pin; configure and verify the ECU and hardware before connection.

DTA ECU pinTTT802 connection described by the guide
11Red — cut open-collector
28Blue — cut ground
26White — ignition pulse
13 or 14Black — ignition pulse ground