Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

Syvecs S-GDI4. Image: Syvecs, reproduced with permission.

Syvecs S-GDI4 is an alternate manufacturer designation for the Syvecs GDI4 standalone ECU. The complete 88-way manufacturer connector schedule, model details and source discrepancies are maintained on the Syvecs GDI4 model page.Vehicle-specific kits can use different assignments. For the Ford Fiesta ST application, consult the Fiesta kit's ECU and loom schedule.The Syvecs S-GDI4 (product code SYV-GDI4, also called SDI or GDi4 in Syvecs materials) is a standalone controller for gasoline direct injection, with an 88-position connector. Syvecs describes integrated control for four-cylinder GDI engines, Ethernet, RS232 and CAN communications, and support for auxiliary sensors and outputs. Confirm actual hardware and firmware against the manufacturer product listing.Manufacturer 88-way pin scheduleThe following is the manufacturer’s GDi4 Pinouts and Wiring Info, dated 3 February 2014, pages 2–3. These are hardware terminal labels and functions for the documented build; wiring and configuration for a particular vehicle kit can differ. In particular, the separately documented Fiesta ST kit describes a different function at terminal 45. Verify the kit, serial, board revision, connector view and calibration before applying a table.PinManufacturer signalFunction1PWRGNDPower ground2IGN8Ignition output 83IGN7Ignition output 74IGN6Ignition output 65IGN5Ignition output 56FUEL10Fuel injector / PWM output 107KNK2Knock sensor 28AN16Configurable analogue / speed / frequency input 169AN14Configurable analogue / speed / frequency input 1410AN12Configurable analogue / speed / frequency input 1211AN10Configurable analogue / speed / frequency input 1012H BRIDGE5H-bridge 513H BRIDGE6H-bridge 614AN7Configurable analogue / speed / frequency input 715AN5Configurable analogue / speed / frequency input 516AN3Configurable analogue / speed / frequency input 317AN1Configurable analogue / speed / frequency input 118LAM1VNTK UEGO sensor 1 Nernst voltage19AN21Thermistor input 2120FUEL15Fuel injector / PWM output 1521RS232#1TXRS232 transmit22FUEL7Fuel injector / PWM output 723FUEL5Spare output with flyback diode24GDI #4 +GDI injector 4 positive25GDI #3 +GDI injector 3 positive26GDI #2 +GDI injector 2 positive27GDI #1 +GDI injector 1 positive28PWRGNDECU power ground29PWRGNDECU power ground30FUEL14Fuel injector / PWM output 1431FUEL13Fuel injector / PWM output 1332FUEL12 / GDI PUMP −Fuel output / GDI pump negative33FUEL11Fuel injector / PWM output 1134FUEL9Fuel injector / PWM output 935KNKKnock sensor 136AN15Configurable analogue / speed / frequency input 1537AN13Configurable analogue / speed / frequency input 1338AN11Configurable analogue / speed / frequency input 1139AN9Configurable analogue / speed / frequency input 940EGT1−K-type thermocouple 1 negative41AN8Configurable analogue / speed / frequency input 842AN6Configurable analogue / speed / frequency input 643AN4Configurable analogue / speed / frequency input 444AN2Configurable analogue / speed / frequency input 245LAM#2VNTK UEGO sensor 2 Nernst voltage46AN22Thermistor input 2247FUEL16Fuel injector / PWM output 1648RS232#1RXRS232 receive49FUEL8Fuel injector / PWM output 850FUEL6Spare output with flyback diode51GDI #4 −GDI injector 4 negative52GDI #3 −GDI injector 3 negative53GDI #2 −GDI injector 2 negative54GDI #1 −GDI injector 1 negative55PWRGNDECU power ground56VBATECU +12 V switched supply57VBATECU +12 V switched supply58GDI PUMP +GDI pump positive59H BRIDGE2H-bridge 260H BRIDGE3H-bridge 3 / DBW +61H BRIDGE4H-bridge 4 / DBW −6210VOUTProgrammable low-current sensor output635VOUT25 V sensor supply 2645VOUT15 V sensor supply 165KNKGNDKnock sensor ground66AN205 V analogue input 2067ANGND2Sensor ground; source calls this ground 168AN195 V analogue input 1969ANGND1Sensor ground; source calls this ground 270EGT1+K-type thermocouple 1 positive71AN185 V analogue input 1872ANGND2Sensor ground 273AN175 V analogue input 1774ANGND1Sensor ground 175LAM2INTK UEGO sensor 2 ion pump76LAMINTK UEGO sensor 1 ion pump77LAMGNDLambda sensor signal ground78COMGNDRS232 communications ground79CAN2LOCAN 2 low80CAN2HICAN 2 high81CAN1LOCAN 1 low82CAN1HICAN 1 high83AN24Thermistor input 2484AN23Thermistor input 2385LANRX+Ethernet receive positive86LANRX−Ethernet receive negative87LANTX+Ethernet transmit positive88LANTX−Ethernet transmit negativeIn the 2014 source, pins 67 and 69 use ANGND2 and ANGND1 labels respectively, but their adjacent ground-number descriptions are reversed; both descriptions are retained and require manufacturer confirmation. The table refers to six H-bridge labels, whereas the product listing summarises four H-bridge outputs; treat the installed ECU’s revision and actual capabilities as unverified until confirmed. The manufacturer lists the injector-high-side connections for solenoid-type GDI injectors.See the Fiesta ST180 plug-in page for its vehicle-specific wiring, and the Syvecs manufacturer index.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Syvecs S-GDI4
Syvecs S-GDI4 standalone engine controller
Syvecs S-GDI4. Image: Syvecs, reproduced with permission.

The Syvecs S-GDI4 (product code SYV-GDI4, also called SDI or GDi4 in Syvecs materials) is a standalone controller for gasoline direct injection, with an 88-position connector. Syvecs describes integrated control for four-cylinder GDI engines, Ethernet, RS232 and CAN communications, and support for auxiliary sensors and outputs. Confirm actual hardware and firmware against the manufacturer product listing.

Manufacturer 88-way pin schedule

The following is the manufacturer’s GDi4 Pinouts and Wiring Info, dated 3 February 2014, pages 2–3. These are hardware terminal labels and functions for the documented build; wiring and configuration for a particular vehicle kit can differ. In particular, the separately documented Fiesta ST kit describes a different function at terminal 45. Verify the kit, serial, board revision, connector view and calibration before applying a table.

PinManufacturer signalFunction
1PWRGNDPower ground
2IGN8Ignition output 8
3IGN7Ignition output 7
4IGN6Ignition output 6
5IGN5Ignition output 5
6FUEL10Fuel injector / PWM output 10
7KNK2Knock sensor 2
8AN16Configurable analogue / speed / frequency input 16
9AN14Configurable analogue / speed / frequency input 14
10AN12Configurable analogue / speed / frequency input 12
11AN10Configurable analogue / speed / frequency input 10
12H BRIDGE5H-bridge 5
13H BRIDGE6H-bridge 6
14AN7Configurable analogue / speed / frequency input 7
15AN5Configurable analogue / speed / frequency input 5
16AN3Configurable analogue / speed / frequency input 3
17AN1Configurable analogue / speed / frequency input 1
18LAM1VNTK UEGO sensor 1 Nernst voltage
19AN21Thermistor input 21
20FUEL15Fuel injector / PWM output 15
21RS232#1TXRS232 transmit
22FUEL7Fuel injector / PWM output 7
23FUEL5Spare output with flyback diode
24GDI #4 +GDI injector 4 positive
25GDI #3 +GDI injector 3 positive
26GDI #2 +GDI injector 2 positive
27GDI #1 +GDI injector 1 positive
28PWRGNDECU power ground
29PWRGNDECU power ground
30FUEL14Fuel injector / PWM output 14
31FUEL13Fuel injector / PWM output 13
32FUEL12 / GDI PUMP −Fuel output / GDI pump negative
33FUEL11Fuel injector / PWM output 11
34FUEL9Fuel injector / PWM output 9
35KNKKnock sensor 1
36AN15Configurable analogue / speed / frequency input 15
37AN13Configurable analogue / speed / frequency input 13
38AN11Configurable analogue / speed / frequency input 11
39AN9Configurable analogue / speed / frequency input 9
40EGT1−K-type thermocouple 1 negative
41AN8Configurable analogue / speed / frequency input 8
42AN6Configurable analogue / speed / frequency input 6
43AN4Configurable analogue / speed / frequency input 4
44AN2Configurable analogue / speed / frequency input 2
45LAM#2VNTK UEGO sensor 2 Nernst voltage
46AN22Thermistor input 22
47FUEL16Fuel injector / PWM output 16
48RS232#1RXRS232 receive
49FUEL8Fuel injector / PWM output 8
50FUEL6Spare output with flyback diode
51GDI #4 −GDI injector 4 negative
52GDI #3 −GDI injector 3 negative
53GDI #2 −GDI injector 2 negative
54GDI #1 −GDI injector 1 negative
55PWRGNDECU power ground
56VBATECU +12 V switched supply
57VBATECU +12 V switched supply
58GDI PUMP +GDI pump positive
59H BRIDGE2H-bridge 2
60H BRIDGE3H-bridge 3 / DBW +
61H BRIDGE4H-bridge 4 / DBW −
6210VOUTProgrammable low-current sensor output
635VOUT25 V sensor supply 2
645VOUT15 V sensor supply 1
65KNKGNDKnock sensor ground
66AN205 V analogue input 20
67ANGND2Sensor ground; source calls this ground 1
68AN195 V analogue input 19
69ANGND1Sensor ground; source calls this ground 2
70EGT1+K-type thermocouple 1 positive
71AN185 V analogue input 18
72ANGND2Sensor ground 2
73AN175 V analogue input 17
74ANGND1Sensor ground 1
75LAM2INTK UEGO sensor 2 ion pump
76LAMINTK UEGO sensor 1 ion pump
77LAMGNDLambda sensor signal ground
78COMGNDRS232 communications ground
79CAN2LOCAN 2 low
80CAN2HICAN 2 high
81CAN1LOCAN 1 low
82CAN1HICAN 1 high
83AN24Thermistor input 24
84AN23Thermistor input 23
85LANRX+Ethernet receive positive
86LANRX−Ethernet receive negative
87LANTX+Ethernet transmit positive
88LANTX−Ethernet transmit negative

In the 2014 source, pins 67 and 69 use ANGND2 and ANGND1 labels respectively, but their adjacent ground-number descriptions are reversed; both descriptions are retained and require manufacturer confirmation. The table refers to six H-bridge labels, whereas the product listing summarises four H-bridge outputs; treat the installed ECU’s revision and actual capabilities as unverified until confirmed. The manufacturer lists the injector-high-side connections for solenoid-type GDI injectors.

See the Fiesta ST180 plug-in page for its vehicle-specific wiring, and the Syvecs manufacturer index.

Revision 2: Syvecs S-GDI4 alternate designation
Syvecs S-GDI4 standalone ECU
Syvecs S-GDI4. Image: Syvecs, reproduced with permission.

Syvecs S-GDI4 is an alternate manufacturer designation for the Syvecs GDI4 standalone ECU. The complete 88-way manufacturer connector schedule, model details and source discrepancies are maintained on the Syvecs GDI4 model page.

Vehicle-specific kits can use different assignments. For the Ford Fiesta ST application, consult the Fiesta kit's ECU and loom schedule.