A dynamometer controller regulates the load applied to the engine or vehicle and may also operate the throttle and record test data. It does not determine the dyno type by itself: an electronic controller can command an eddy-current brake, a water valve, a hydrostatic system or an electrical machine, each with different physical limits. Start with Dynamometers.
Manual and older controls
A basic manual system uses an operator, speed indication, a torque display and a valve or electrical field control. The operator changes the load while observing the engine. Mechanical linkages, separate analogue indicators and chart recorders can be found on older installations. Manual control can perform a steady test, but maintaining a repeatable target depends heavily on operator response.
Automatic feedback is not exclusively digital or new. A historical University of Edinburgh review describes a 1950 electronic road-load simulation using a speed generator, analogue control channels and an amplifier controlling dynamometer field current. It also discusses open-loop programmed cycles and feedback-based approaches. University of Edinburgh dynamometer control research.
Closed-loop operation
- A speed pickup and often a load cell or shaft-torque sensor report the current condition.
- The controller compares the measured value with the requested speed or torque (the setpoint).
- It adjusts an output such as field current, a water or oil valve, or an inverter torque command.
- The process repeats as the engine and absorber respond. A separate throttle actuator or operator controls engine output where required.
A proportional-integral (PI) or proportional-integral-derivative (PID) controller is one common approach; tuning affects response, overshoot and stability. Filtering, actuator limits, delays and changing operating conditions matter. Modern systems can use other strategies, scheduled control parameters or feed-forward. An actual eddy-current engine control study compares several approaches. Active control of an engine dynamometer.
Common test modes
- Manual load: operator sets the actuator; speed and torque result from the interaction of engine and absorber.
- Speed hold: absorber load is adjusted to maintain a chosen speed as the throttle or engine torque changes. Useful for steady-state fuel and ignition mapping when the absorber can supply the necessary torque.
- Torque or load hold: feedback targets the configured torque measurement. Engine throttle and load interact; the controller arrangement must provide a viable operating point rather than assume independent speed and torque control.
- Sweep or ramp: speed changes over a defined range and rate, or according to available power and inertia. The exact mode and compensation differ between systems.
- Road-load simulation: a model commands resistance based on speed and possibly acceleration or a recorded drive cycle. An absorber-only machine cannot reproduce every downhill, overrun or externally driven condition; motoring requires suitable hardware.
Measurements and safeguards
Torque transducers require zero and calibration checks; speed sensing, gearing, roller diameter, sample rate and channel timing must match the test. Load-cell reaction torque is not necessarily total engine torque during acceleration because rotating inertia and losses also matter. Report the measurement location, test mode, environmental correction and any estimated drivetrain losses with results.
Controller output is constrained by actuator, machine torque–speed and heat-rejection limits. A target outside the envelope cannot be held regardless of software. Overspeed, loss of cooling, sensor faults, failed communications and emergency stop need a machine-specific safe response. A dyno controller does not replace proper restraints, guarding, ventilation and manufacturer procedures.
Aftermarket dyno controllers and retrofit systems
There are many alternatives to the electronics originally supplied with a rolling road or engine dyno. Some packages combine data acquisition, software and closed-loop load control; others only measure speed and force. A system advertised for an existing dyno is not automatically a plug-in replacement: the number of independently controlled axles or hubs, brake interface, sensors and safety circuits must match the particular machine. The following are selected examples, not a ranking or complete market list. Product descriptions and links were checked on 17 November 2026; versions, options, support and availability can change.
Adaptable acquisition and load-control systems
| System | What the supplier describes | Retrofit points to check |
|---|---|---|
| YourDyno Standard v5 / Ultimate | Instrument boxes and PC software for inertia, chassis, engine and hub installations. Standard v5 provides speed and load-cell inputs and brake-control outputs; the supplier offers kits for eddy-current and water-brake systems. Chassis kit; Standard instructions. | Specify brake power supply or water-valve actuator and sensors. The Standard instructions describe two boxes in tandem or an Ultimate for a four-hub installation; confirm exact channels and options. |
| SportDevices SP1+, SP5 and SP6 | DAQ and brake-control families used with SportDyno software. The SP5 describes engine and chassis testing and optional AWD; the SP6 offers two-brake and four-hub configurations. | SP1 and SP1+ differ; SP5 AWD requires additional components and activation, and SP6 variants have different channel counts. Match the power supply, load cells and speed pickups to the installation. |
| PEREK DC2 / DC2L | Integrated controller/computer and Dyno2 software for inertial and braked installations. PEREK describes DC2 and DC2L variants and supports upgrades of existing hardware. | DC2 supports independently controlled 4WD chassis and four-hub layouts; DC2L has a more limited configuration range including mechanically synchronised 4WD chassis. A compatible eddy-current power module or valve actuator is separate from the control signal. |
| Dynostar DAS A801 | Roller-chassis upgrade kit with Dyno Station software, data-acquisition and junction boxes, remote, drum-speed sensor and load cell. The published kit also lists an eddy-current brake power supply and calibration weight. | Confirm brake voltage/current, axle arrangement and whether the supplied power stage and sensor interfaces suit the old dyno. The listing describes roller-chassis retrofits, not every dyno layout. |
| Accudyno Forza DS | Acquisition and digital brake control for absorber dynos, including hydraulic and eddy-current applications; the supplier describes automatic control through voltage, PWM or servo outputs. Accudyno overview. | The eddy-current brake power supply is not included in the cited product. Check the available speed/load channels and the separate hub-specific option for the intended arrangement. |
| Performance Trends Dyno DataMite | DataMite hardware and software for engine or chassis inertia and absorber measurements. The supplier describes retrofits to several dyno brands; its controller guide describes an eddy-current control setup. | DAQ size, software edition, controller and brake power box are distinct choices. Confirm whether the quotation includes automatic load control and the appropriate power stage or water-valve drive. |
| Dastek upgrades through Advanced Dyno Solutions | ADS lists Dastek controller upgrade packages for existing 2WD and 4WD dynos, plus SportDevices accessories. See the Dastek profile. | Request the package's supported dyno, channels, brake driver, software and installation details. The listing alone does not establish every feature or compatibility with every make. |
| SuperFlow WinDyn5 conversions | Configurable control and acquisition conversions for engine and chassis test cells. SuperFlow's brochure names its own machines and several third-party makes, including Froude, Stuska, Maha, Dynojet and Dynocom. | This is a configured test-cell conversion; confirm the exact model, brake, valve arrangement, sensors and integration with SuperFlow. A listed make is not a guarantee for every machine. |
| 6DM REO-dEC R2 / REO-dCA R2 | The dEC R2 is an engine-dyno controller; dCA R2 expands it into a test-bed control and acquisition system. The supplier offers output modules for hydraulic, eddy-current and AC applications. | Intended for engineered engine-test installations and upgrades. Specify the actual absorber, throttle, transducer box and interfacing; confirm any particular chassis-dyno application separately. |
| Hydra-Test HTC-S | Modular acquisition and control system which the supplier says can be adapted to transmission stands, engine and chassis dynos; it lists configurable inputs, outputs and closed-loop modes. | Discuss the application with the supplier. Channel capacity, wiring, control strategy and brake interface depend on the engineered configuration; do not assume a universal drop-in kit. |
| dynoKRAFT ADAQ | ADAQ software and ADAQbase hardware are described with manual, semi-automatic and PID or non-PID brake modes; the supplier describes four-hub support using two base controllers. | Offered with dynoKRAFT equipment; ask the supplier whether an existing third-party machine can be converted and which hardware and brake power electronics are required. |


Measurement-only, older and other options
- SportDevices SP3 is a useful older retrofit example: its published instructions explicitly say it measures a braked dyno but does not control the brake. An existing brake controller is required.
- DTec DYNertia3 supports inertia measurement and open-loop brake measurement. Its manual states that it does not automatically vary brake load to hold a selected RPM. A separately controlled absorber remains necessary.
- Accudyno Gyra DS is the maker's inertia-measurement system; Forza DS is the separate absorber-dyno system. Do not assume a Gyra inertia kit supplies load control.
- Precision DynoTech describes DAQ products and RevBench software for digitising older dynos. Confirm automatic brake-control hardware and supported operating modes with the supplier.
- SAJ DCATS and Dyna Pro brake upgrades are examples tied to the supplier's own dyno families. Dyna Pro describes adding an actual eddy-current brake to specified inertia dynos, not simply changing software.
- DIY-Dyno is an open-source ESP32 measurement and control project for builders. Its repository describes an alpha-stage project; check the current implementation and validation before relying on any brake-actuation or safety function.
What to specify before replacing a controller
Identify the mechanical dyno and absorber separately from its existing electronics. Record the roller or hub count, axle linkage, absorber torque and speed envelope, field voltage and current or hydraulic-valve type, load-cell range and wiring, speed-pickup signals, engine-RPM source and power supply. Confirm whether the intended job needs inertia-only runs, steady-state hold, controlled sweeps, independent axle control, logging, CAN or a particular correction method.
Ask the supplier which power electronics or actuators, sensors, licences, wiring, calibration tools, emergency-stop interface, software, installation and support are included. Set up and verify roller inertia, speed and load-cell calibration and the response of the entire control and safety chain using the equipment maker's procedures. Replacing the electronics does not increase the brake's mechanical or cooling rating and does not give an absorption-only brake motoring capability.

Sources
- University of Edinburgh: dynamometer control research, historical review.
- Active control of an engine dynamometer, feedback and PI/PID comparison.
- Closed-loop torque and speed control on an eddy-current dynamometer, throttle and absorber control example.
Integrated manufacturer-specific controls
COSBER / DynoCosber describes its own software, handheld controller and PID load control as part of its chassis-dyno systems. The available sources do not establish a separately sold universal retrofit for other makes; confirm compatibility directly. COSBER dyno catalogue.
Related company profiles
SportDevices · YourDyno · PEREK · Dastek · Froude.