Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Denso
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

The gasoline engine ECU

Denso's gasoline engine control unit meters fuel and times the spark from the sensor signals. Denso's history of that product starts with electronic fuel injection research in 1967, independent injection for each cylinder, and semiconductors made in house. Toyota approved mass production in 1972. The current product page also describes injector-correction in the ECU: the unit watches each injector open and close, and corrects that cylinder's volume and timing. That correction is a control function. It is not a code printed on the injector.

The diesel systems that Denso calls ECD are on Denso diesel. A gasoline calibration does not belong on an ECD-V or common-rail diesel controller.

Toyota's number and Denso Ten

Toyota's engine-computer number, in the 89661 series, is the car maker's number. On a diesel bulletin it can sit beside a Denso 175800 number, as on the Prado 1KD. The same 89661 series is also used where the supplier is not identified. The Denso number, or the label, is what places the unit on this page.

A Denso Ten paper, Engine Control ECU Development for the 2005 standard model, says the work was done with Toyota and with Denso, and that this model moved the engine controller into the engine compartment. Denso Ten is a different author from the Denso diesel manuals. The paper does not make every Toyota engine computer a Denso ECU.

Sources

Denso, 75-year history. Electronic fuel injection from 1967 and Toyota approval in 1972. Electronic control history. Accessed 2026-11-13. Denso, engine ECU product page. Injection, ignition, and injector correction. Engine ECU. Accessed 2026-11-13. Denso Ten, Engine Control ECU Development for '05 Standard Model. Collaboration with Toyota and Denso, and the engine-compartment mounting. 2005 standard-model paper.

Volvo Drive-E tuning reference

See the Volvo Denso Drive-E ECU tuning guide for older SH72546 and newer Gen2 programming references and model-specific engine information.

A third-party file listing identifies a Range Rover 4.2 supercharged AJ33S as Denso MB279700, HW NNN500411 and SW NV502089. See the supercharged Land Rover petrol tuning guide; this family page does not establish a variant pinout or universal fitment.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Denso petrol

The gasoline engine ECU

Denso's gasoline engine control unit meters fuel and times the spark from the sensor signals. Denso's history of that product starts with electronic fuel injection research in 1967, independent injection for each cylinder, and semiconductors made in house. Toyota approved mass production in 1972. The current product page also describes injector-correction in the ECU: the unit watches each injector open and close, and corrects that cylinder's volume and timing. That correction is a control function. It is not a code printed on the injector.

The diesel systems that Denso calls ECD are on Denso diesel. A gasoline calibration does not belong on an ECD-V or common-rail diesel controller.

Toyota's number and Denso Ten

Toyota's engine-computer number, in the 89661 series, is the car maker's number. On a diesel bulletin it can sit beside a Denso 175800 number, as on the Prado 1KD. The same 89661 series is also used where the supplier is not identified. The Denso number, or the label, is what places the unit on this page.

A Denso Ten paper, Engine Control ECU Development for the 2005 standard model, says the work was done with Toyota and with Denso, and that this model moved the engine controller into the engine compartment. Denso Ten is a different author from the Denso diesel manuals. The paper does not make every Toyota engine computer a Denso ECU.

Sources

  • Denso, 75-year history. Electronic fuel injection from 1967 and Toyota approval in 1972. Electronic control history. Accessed 2026-11-13.
  • Denso, engine ECU product page. Injection, ignition, and injector correction. Engine ECU. Accessed 2026-11-13.
  • Denso Ten, Engine Control ECU Development for '05 Standard Model. Collaboration with Toyota and Denso, and the engine-compartment mounting. 2005 standard-model paper.

Volvo Drive-E tuning reference

See the Volvo Denso Drive-E ECU tuning guide for older SH72546 and newer Gen2 programming references and model-specific engine information.

Revision 3: Denso petrol

The gasoline engine ECU

Denso's gasoline engine control unit meters fuel and times the spark from the sensor signals. Denso's history of that product starts with electronic fuel injection research in 1967, independent injection for each cylinder, and semiconductors made in house. Toyota approved mass production in 1972. The current product page also describes injector-correction in the ECU: the unit watches each injector open and close, and corrects that cylinder's volume and timing. That correction is a control function. It is not a code printed on the injector.

The diesel systems that Denso calls ECD are on Denso diesel. A gasoline calibration does not belong on an ECD-V or common-rail diesel controller.

Toyota's number and Denso Ten

Toyota's engine-computer number, in the 89661 series, is the car maker's number. On a diesel bulletin it can sit beside a Denso 175800 number, as on the Prado 1KD. The same 89661 series is also used where the supplier is not identified. The Denso number, or the label, is what places the unit on this page.

A Denso Ten paper, Engine Control ECU Development for the 2005 standard model, says the work was done with Toyota and with Denso, and that this model moved the engine controller into the engine compartment. Denso Ten is a different author from the Denso diesel manuals. The paper does not make every Toyota engine computer a Denso ECU.

Sources

  • Denso, 75-year history. Electronic fuel injection from 1967 and Toyota approval in 1972. Electronic control history. Accessed 2026-11-13.
  • Denso, engine ECU product page. Injection, ignition, and injector correction. Engine ECU. Accessed 2026-11-13.
  • Denso Ten, Engine Control ECU Development for '05 Standard Model. Collaboration with Toyota and Denso, and the engine-compartment mounting. 2005 standard-model paper.

Volvo Drive-E tuning reference

See the Volvo Denso Drive-E ECU tuning guide for older SH72546 and newer Gen2 programming references and model-specific engine information.

A third-party file listing identifies a Range Rover 4.2 supercharged AJ33S as Denso MB279700, HW NNN500411 and SW NV502089. See the supercharged Land Rover petrol tuning guide; this family page does not establish a variant pinout or universal fitment.