Page organisation in this revision
- Page type
- Technical article
- Subject
- ABS / DSC
- Parent
- Delphi DBC 7 ABS
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Delphi
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
ABS and traction systems · System reference
Scope and connector
Daewoo U-145/173 BL2,3 export ABS EBCM harness connector. The Daewoo manual names DBC 7 in section 4F-3 and labels the connector drawing as a harness end view in section 4F-103. This is a vehicle/export-configuration-specific table, not a generic DBC 7 pinout. C11 is a vent tube, not an electrical terminal.
Documented terminal assignments
TerminalDocumented connectionABattery supply, hot at all timesBBattery supply, hot at all timesCEBCM groundDPump motor groundA3Rear-left wheel-speed sensor highA4Rear-left wheel-speed sensor lowA5Rear-right wheel-speed sensor lowA6Rear-right wheel-speed sensor highA7Front-right wheel-speed sensor highA8Front-right wheel-speed sensor lowA9Front-left wheel-speed sensor lowA10Front-left wheel-speed sensor highA11Switched ignitionB3Brake warning lamp outputB6Serial data input/outputB8ABS warning lamp outputC3Buffered wheel-speed signal to Siemens ECMC7Brake switch inputC9PWM rough-road signal to Delphi MR-140 ECMC11Vent tube; not an electrical contact
Only the listed assignments are included here; omission does not prove a terminal is unused. Compare the source and the exact vehicle wiring diagram before connection or testing. The source describes a specific application or controller variant, not a universal family pinout.
Sources
Daewoo U-145/173 ABS manual, sections 4F-3 and 4F-103
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Daewoo U145 U173 DBC 7 export EBCM connector pinout
ABS and traction systems · System reference
Scope and connector
Daewoo U-145/173 BL2,3 export ABS EBCM harness connector. The Daewoo manual names DBC 7 in section 4F-3 and labels the connector drawing as a harness end view in section 4F-103. This is a vehicle/export-configuration-specific table, not a generic DBC 7 pinout. C11 is a vent tube, not an electrical terminal.
Documented terminal assignments
| Terminal | Documented connection |
|---|
| A | Battery supply, hot at all times |
| B | Battery supply, hot at all times |
| C | EBCM ground |
| D | Pump motor ground |
| A3 | Rear-left wheel-speed sensor high |
| A4 | Rear-left wheel-speed sensor low |
| A5 | Rear-right wheel-speed sensor low |
| A6 | Rear-right wheel-speed sensor high |
| A7 | Front-right wheel-speed sensor high |
| A8 | Front-right wheel-speed sensor low |
| A9 | Front-left wheel-speed sensor low |
| A10 | Front-left wheel-speed sensor high |
| A11 | Switched ignition |
| B3 | Brake warning lamp output |
| B6 | Serial data input/output |
| B8 | ABS warning lamp output |
| C3 | Buffered wheel-speed signal to Siemens ECM |
| C7 | Brake switch input |
| C9 | PWM rough-road signal to Delphi MR-140 ECM |
| C11 | Vent tube; not an electrical contact |
Only the listed assignments are included here; omission does not prove a terminal is unused. Compare the source and the exact vehicle wiring diagram before connection or testing. The source describes a specific application or controller variant, not a universal family pinout.
Sources
Revision 1: Daewoo U145 U173 DBC 7 export EBCM connector pinout
ABS and traction systems · System reference
Scope and connector
Daewoo U-145/173 BL2,3 export ABS EBCM harness connector. The Daewoo manual names DBC 7 in section 4F-3 and labels the connector drawing as a harness end view in section 4F-103. This is a vehicle/export-configuration-specific table, not a generic DBC 7 pinout. C11 is a vent tube, not an electrical terminal.
Documented terminal assignments
| Terminal | Documented connection |
|---|
| A | Battery supply, hot at all times |
| B | Battery supply, hot at all times |
| C | EBCM ground |
| D | Pump motor ground |
| A3 | Rear-left wheel-speed sensor high |
| A4 | Rear-left wheel-speed sensor low |
| A5 | Rear-right wheel-speed sensor low |
| A6 | Rear-right wheel-speed sensor high |
| A7 | Front-right wheel-speed sensor high |
| A8 | Front-right wheel-speed sensor low |
| A9 | Front-left wheel-speed sensor low |
| A10 | Front-left wheel-speed sensor high |
| A11 | Switched ignition |
| B3 | Brake warning lamp output |
| B6 | Serial data input/output |
| B8 | ABS warning lamp output |
| C3 | Buffered wheel-speed signal to Siemens ECM |
| C7 | Brake switch input |
| C9 | PWM rough-road signal to Delphi MR-140 ECM |
| C11 | Vent tube; not an electrical contact |
Only the listed assignments are included here; omission does not prove a terminal is unused. Compare the source and the exact vehicle wiring diagram before connection or testing. The source describes a specific application or controller variant, not a universal family pinout.
Sources