Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Ford Fiesta Mk7 ST180, with product code SGDI-MK7ST. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Ford Fiesta Mk7 ST180 installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Ford Fiesta Mk7 ST180 product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer SGDI4 ECU and Fiesta loom mapping
From the Syvecs Ford Fiesta ST Mk7 guide, version 1.0, ECU wiring pages 6–7. The first pin column identifies the Syvecs ECU terminal; the Ford B/E references and loom labels are copied from the guide’s application chart. Empty cells mean the source gives no connection; they do not establish that a cavity is electrically unused. Some labels describe wiring moved between factory positions; verify the installed patch-harness revision and the original diagram.
| SGDI4 pin | Syvecs function | Ford connector / harness reference | Vehicle function |
|---|---|---|---|
| 1 | Power ground | B96 | Power ground |
| 2 | Ignition 8 | E53 | Ign 4 |
| 3 | Ignition 7 | E52 | Ign 3 |
| 4 | Ignition 6 | E51 | Ign 2 |
| 5 | Ignition 5 | E50 | Ign 1 |
| 6 | Fuel 10 | E2 | Bypass solenoid |
| 7 | Knock 2 | E57 | Knock 2 |
| 8 | Input 16 (5V/TH/BI/FREQ) | — | — |
| 9 | Input 14 (5V/TH/BI/FREQ) | — | — |
| 10 | Input 12 (5V/TH/BI/FREQ) | — | — |
| 11 | Input 10 (5V/TH/BI/FREQ) | E36 | Intake cam |
| 12 | Thermo − 2 | — | — |
| 13 | Thermo + 2 | — | — |
| 14 | Input 7 (5V/TH/BI/FREQ) | B8 | MAF |
| 15 | Input 5 (5V/TH/BI/FREQ) | — | — |
| 16 | Input 3 (5V/TH/BI/FREQ) | — | — |
| 17 | Input 1 (5V/TH/BI/FREQ) | E35 | MAP |
| 18 | Lambda V1 | E26 | Lambda V |
| 19 | Input 21 (TH) | E23 | ECT |
| 20 | Fuel 15 | B22 | Canister purge |
| 21 | RS232 1 TX | — | — |
| 22 | Fuel 7 | E1 | Lambda heater |
| 23 | Fuel 5 | E16, moved from 30 | Cooling fan high speed |
| 24 | Ignition 4 | E86 | GDI 4+ |
| 25 | Ignition 3 | E92 | GDI 3+ |
| 26 | Ignition 2 | E87 | GDI 2+ |
| 27 | Ignition 1 | E91 | GDI 1+ |
| 28 | Power ground | B97 | Ground |
| 29 | Power ground | B99 + CAN bridge V2 pin 3 | Ground |
| 30 | Fuel 14 | B5, moved from 23 | VVT exhaust |
| 31 | Fuel 13 | B43, moved from 50 | VVT intake |
| 32 | Fuel 12 / GDI pump − | E78 | Fuel volume control − |
| 33 | Fuel 11 | E48 | Turbo bypass |
| 34 | Fuel 9 | — | — |
| 35 | Knock 1 | E59 | — |
| 36 | Input 15 (5V/TH/BI/FREQ) | E42 | Oil pressure switch |
| 37 | Input 13 (5V/TH/BI/FREQ) | B45 | PPS (PWM) |
| 38 | Input 11 (5V/TH/BI/FREQ) | E37 | Exhaust cam |
| 39 | Input 9 (5V/TH/BI/FREQ) | E49 | Crank |
| 40 | Thermo − 1 | — | — |
| 41 | Input 8 (5V/TH/BI/FREQ) | B30 | Clutch switch |
| 42 | Input 6 (5V/TH/BI/FREQ) | B66 | Brake switch |
| 43 | Input 4 (5V/TH/BI/FREQ) | B52 | A/C pressure |
| 44 | Input 2 (5V/TH/BI/FREQ) | E38 | FP |
| 45 | CAN low 3 | — | — |
| 46 | Input 22 (TH) | — | — |
| 47 | Fuel 16 | E47 | Boost solenoid |
| 48 | RS232 RX | — | — |
| 49 | Fuel 8 | B2 | A/C clutch |
| 50 | Fuel 6 | E31, moved from 31 | Starter relay ground |
| 51 | Fuel 4 | E83 | GDI 4− (spare) |
| 52 | Fuel 3 | E82 | GDI 3− |
| 53 | Fuel 2 | E81 | GDI 2− |
| 54 | Fuel 1 | E84 | GDI 1− |
| 55 | Power ground | Relay 30 & 86 | — |
| 56 | Battery supply | B101, B102 | VBATT |
| 57 | Battery supply | B103; CAN bridge V2 pin 12 | VBATT |
| 58 | H-bridge 1 | E94 | DBW+ |
| 59 | H-bridge 2 | E89 | DBW− |
| 60 | H-bridge 3 | B39 | Fuel pump ECU |
| 61 | H-bridge 4 | E79 | Fuel volume control + |
| 62 | 10 V output | — | — |
| 63 | 5 V output 2 | — | — |
| 64 | 5 V output 1 | B14; E3, E5, E7 | A/C, MAP, brake vacuum, crank, TPS |
| 65 | Knock ground | E58, E60 | — |
| 66 | Input 20 (5V/knock 4) | B71 | Low fuel pressure |
| 67 | Sensor ground 2 | B9, B17, B19 | A/C, clutch switch, MAF |
| 68 | Input 19 (5V/knock 3) | — | — |
| 69 | Sensor ground 1 | — | — |
| 70 | Thermo + 1 | — | — |
| 71 | Input 18 (5V) | E34 | TPS2 |
| 72 | Sensor ground 2 | — | — |
| 73 | Input 17 (5V) | E33 | TPS1 |
| 74 | Sensor ground 1 | E10, E18, E19, E20, E22, E54 | TPS, MAP, VVT, FP |
| 75 | CAN high 3 | — | — |
| 76 | Lambda I1 | E39 | — |
| 77 | Lambda ground | E25 | — |
| 78 | Communications ground | — | — |
| 79 | CAN low 2 | — | — |
| 80 | CAN high 2 | — | — |
| 81 | CAN low 1 | CAN bridge pin 6 | — |
| 82 | CAN high 1 | CAN bridge pin 15 | — |
| 83 | Input 24 (TH) | B75 | IAT |
| 84 | Input 23 (TH) | B32 | ACT |
| 85 | LAN RX+ | White/orange | Ethernet socket |
| 86 | LAN RX− | Orange/white | Ethernet socket |
| 87 | LAN TX+ | White/green | Ethernet socket |
| 88 | LAN TX− | Green/white | Ethernet socket |
The diagram also uses a CAN bridge, with the bridge version noted in the relevant rows; the guide depicts vehicle connector positions separately and should be consulted for wire routing and connector orientation.